poulan pro pp4218a chainsaw carburetor fuel line repair kit install HIPA 

I watched four other videos that were trial and error and made the job look so much more difficult. Yours was no fluff, no background music, no editing parts out, and the job only took 20 minutes. Perfectly done. Thank you for showing the RIGHT way to make a how-to video! 💯

Worked for me. I just replaced the fuel lines and bulb and cleaned the carb. Now it stays running at idle once again! Thanks so much!

Thank you sir. This was my first time changing a carb on a chainsaw. Your video made it easy to do. Two pulls and it fired right up.

You made it so easy my little sister could do it ! Thanks...

Great video, easy to follow and covers all the bases. Thanks!

Great video, very informative and straightforward. My loose fuel lines are now secure and my chainsaw is running great...but now you have me wanting to change my entire carburetor. When that times comes this will be my guide. Keep Crushing Brother!

Excellent video. My PP4218A quit. Have the kit on order. Will be doing the job. Thanks for taking the time to do this video! It's a great help!

THANK YOU so much for this video!!! Excellent job of explaining carb out and reassembly.

Man, I cannot express enough how well done this video is. I have no idea how you managed to get such a good angle on the inside of that gas tank for showing how to feed the lines (which is the hardest part, really). Outstanding content that saves so many of us time and money.

Love video. I wish I had found it before I started. Once I started the video and followed along, it was simple. Thank you!

Thank you! Very clear instructions. A common sense approach at repairs with teaching and no lecturing.

The fuel lines on my Poulan Pro PP4218AVX 42cc chainsaw were rotten and this video helped me replace them. Every step was explained and shown really well. Thank you so much!!!

OUTSTANDING video. I have minimal technical skills and was able to perform this repair. Thank you.

Thanks for showing how those fuel hoses go. Mine were missing and I was lost. Thanks a lot!!

I was ready to throw mine away it had gotten so bad. Now it runs like a new machine. THANKYOU!

Awesome video man! Great point about the carburetor gasket lining up with the impulse hole. I recently did this exact repair on the same saw and couldn't get the saw to start because the carb gasket impulse hole wasn't drilled properly and covered the hole

Thank you for this video and the link to the carb kit. I bought the kit from your link and it came the next day. Impressed with the kit. 🇺🇲👍

Thank you for this video! I went step by step and my saw is up and running! I linked your video on mine also. 😁

Best video I’ve ever seen on fuel lines replacement

Thank you for sharing this! It helped. Salute!

It was a pleasure watching you work... thank you

Thanks. Great video. Worked perfect.

Thank you for the great video! Fired up 1st try.

Hipa has really good parts and fair prices, never had a problem with there stuff yet Plus they have the parts in stock and fast shipping 😊😊

THank you - helped me to fix mine :)

Thank you very much for this video. Very good presentation. 👍

LEARNED A LOT THANK YOU

I ordered the carb for my pp4218A. Installed and pulled the choke out it fired the first pull. Pushed the choke in halfway pulled it again it started but didn't idol. Turned the screw out about 3/4 of a turn started and ran perfect. The carb on it was supposed to be new but wouldn't run right. Now the problem I have is when you put the top cover on the throttle cable get hung on the choke and you can't pull the choke all the way out to where it locks in place. Guess I'll have to figure that out next.

Hey dude. You make it look so easy! But you should slow down and explain what you are doing and why. Some of us are dummies and have never replaced a carb! You probably do it all the time. Thanks!

I pull the intake off to do that job , it gives you a lot more elbow room and makes it easier to see what you are doing

9:06 sometimes i have to swedge the tubing with a phillips so it will fit.

Awesome video! You definitely helped me today! Thank you

This video was very helpful, thank you

Love you’re voices .great job mate

Good job on that

Very well done.

Great video bro, I have a question. My throttle cable keeps slipping making the carb not engage. I have to reach in the little crack in the saw between the carb breather and handle and slide it forward, but it won’t stay to engage the carb. How do I make it stay? Thank you for the straight up explanational video.

thank you

Thank you, your video made it easy and it fired right up. It does shut down after running a few minutes and I assume that a carburetor adjustment will remedy the problem. I'm curious, the second carburetor screw, the one furthest from the air filter, what does it adjust and what is the proper way to adjust it? Also, which screw should I be adjusting , given my description?

Good video. However, I have one complaint. When describing the fuel lines and where they go, do one line at a time instead of getting ahead of yourself and mixing them up. I wasn't able to easily determine which fuel line (small diameter or large) ran where and why. Good video, but could have been broken down in steps more simply. Apologies for the whining...it was still VERY helpful. I've only ever used a chainsaw a few times before, nevermind replacing a complete fuel delivery system. BTW, my efforts (and yours) resulted in success. Thanx again.

I have this same saw I'm trying to repair for a tenant. I plan on replacing the carb but first I need to figure out how to get the brake lever to disengage. I've taken it apart enough to where I should be able to get to the brake assembly but this model it appears you have to take the chassis apart. Do you have any videos related to this. Any info would be appreciated

OK thanks

You will.eventually learn that "slight" difference in choke linkage on the aftermarket carbs is a critical issue that can and has caused saws to fail to accelerate. The metal rod and lever used on the after market carbs can skip and prevent the upper butterfly to open. The upper port is the engine acceleration, high speed port and without it the saw cannot be used. The plastic lever used on the OEM carb functions like a trigger, locking carb linkage in position until the trigger is depressed, at which time the locked linkage is released.

There was a thicker and a thin line for the primer and fuel pump. Did you not use the thinner of the two for anything? Also the rope chord won’t budge when I assembled it back together.

The old brittle gas lines broke off in the gas line holes. I'm trying to figure out how to the get the old lines out of the holes. The fuel line holes on my saw are right next to the engine instead of behind the primer bulb like the saw in your video and the holes are also much smaller. I don't think the larger line will even go through them. I know now that I need much longer needle nose plyers.

What are the high and low settings supposed to be set at

Mine started pouring fuel. I replaced everything with this kit, and new 50:1 fuel pre mixed and it popped like it wanted to start and then that’s it. Any ideas?

👏👏👏

my replacement kit came w/ 2 tubes of different sizes, are you using different size tubes?

I can appreciate a straight to the point, no filler instructional video like this one! Obviously you've spent a lot of time around these pieces and it shows! I was confused about the long/short fitting at the p-bulb and that's what put me here. You cleared it up for me. I also like that you changed the routing of the fuel supply and suction lines at the fuel tank! Love the use of the term "stab" that you like to use 😂. Overall, I greatly appreciate your knowledge and the time you took out of your day to help me and other viewers out!!! Thanks brother!!!! You're awesome but Joe Biden Sucks!

Hello, I have watched your videos a number of times and decided to take a stab at it myself.Im working with a Poulon Pro PP4218AVHD, 42cc Chainsaw. It ran prior to doing what I did and now it won't start at all. I replaced the fuel lines, gaskets and Carb along with a new spark plug gapped at .030. I have rerouted the fuel lines and adjusted the carb as you as prescribed ?????? What do you think I should try next? Thanks: Bob

How much for a carburetor kit now! (2024) Should you put a new carburetor in always are just fuel lines? One of my lines just broke. I will replace the primer bulb. Great video!

Спасибо за это видео. Мне тоже не понравилось, расположение топливных линий. Хотел пределывать, но лень. Ведь производитель, зачем то сделал так. Ваше видео, добавило уверенности, что надо переделывать. С наилучшими пожеланиями из России.

Don't you want to make carb adjustments WITH the air filter in place? It restricts airflow (slightly) and will affect the fuel/air mixture. You had to richen up the mixture likely because you were getting too much air in the carb (compared to having the air filter in place).

I have this exact saw, bought it for a steal from someone who said he replaced the carb last season & drained it. Worked great the first time I used it 3 months ago, now it starts for a min but dies after a few seconds whether I use throttle or not... wondering if I should go ahead & do this repair for good measure?

So instead of pushing fuel through with the primer, you're suckling it through? Not sure I trust my primer bulb to do that reliably. But good video explaining everything you're doing. .

Hi what’s the size of the fuel lines? Thanks

How the heck did you get the fuel line through the hole?!

The saw I'm working on has the two different size lines I hate that.

does Hipa just sell carb gaskets and diaphrams

What is the carb kit number The link is closed 😢😢😢

Wonder what it cost to have it fixed ??😮

Poolawn lol😂

Did the exact same procedure, and now it will not start to save my ass.

no offense to the customer but how much of a puts do you have to be that you just globbed silicone all over the gasket thinking that would be kosher?

Best way to work on a poulan is throw it in the trash and buy a Stihl