Power Injection to Stop Flickering - Govee Outdoor Lights - Walkthrough 

☑ Check out my sponsor to begin your FREE 14 day trial to Aura: aura.com/chrismaher 🚨 UPDATED DAILY! BEST TECH DEALS on AMAZON: bit.ly/48FGnUv ***Thanks @Mrrazvyyo for pointing out the reason the power injection didn't work when I tried doing it right after the power supply! The gnd is the wire that has the black line on it. The Data is still the middle and the Voltage is the wire that has nothing written or marked on it. In the video I incorrectly said the wire with the black line on it was voltage and the gnd was the one that had nothing on it. Govee Permanent Outdoor Lights: amzn.to/3ZV9LD6 Govee Permanent Outdoor Lights Pro: amzn.to/3twvs0h Govee Christmas String Lights: amzn.to/45Cp98K Govee Curtain Lights: amzn.to/3tz5fOE Wire Stripper: amzn.to/3M1LzcE Wago Connectors: amzn.to/3N8uRsD 18 Gauge Silicone Wire: amzn.to/46IcQbA Other Permanent Outdoor Lights Video's I've Done: Splitting / Y Connect Govee Outdoor Lights: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-cG0xsnRm-As.html Cut, Extend, Waterproof Govee Outdoor Lights: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-b2Pc0BzKIk8.html Govee Permanent Outdoor Lights Pro Setup: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7JBUI4SF5sI.html Cutting Off Extra Lights: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-eG4sKOmZW9k.html DreamView Sync for Govee Lights: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-a_haIayX1gc.html Eufy Outdoor Permanent Lights: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-aesOK3DBr1Q.html The best way to help support my channel is to like, comment, make sure your subscribed and share my videos with as many people as you can. The other way is to use my links above as I get a small % at no extra cost to you if you buy something. Thank you all for the support!

I ordered some leds from btf I was gonna use for my Christmas tree. I remembered you had a video on which wire was which and you answered my question in this video.

As always... your vids save a lot of headaches from happening!!! Thanks for the info

As someone from a past video said “You are out here doing gods work”

Chris, glad I ran into your videos. I do have a question, you have mentioned that it does matter where you can cut the lights. I cut 3 lights after the connector and added an extension, it worked for a bit now they don’t work. What could be the issue? I jumped that section to another connector and it works but only the first three.

Thank you Chris.

Chris your videos are the best out there regarding Govee lights. Have you tried to power inject 9 segments? Is it something that can be done using your method? Will the app re-adjust to recognize 11 segments knowing that the limit is 9?

IDEA FOR VIDEO: On the PRO 200 feet version the power brick gets pretty warm when running all the lights. What if you made a power injection video, but utilized a separate 36V power injector.

Love the channel. Can you feed power to the middle of a strip and power both sides of the strip. Say you have a 6 foot long strip and feed the single source power in at the middle of the strip with a power supply , will it light the whole strip or only half.

Is it possible for you to go through a wiring diagram for a video that shows your testing of where a Y is possible, length of extension cables, and where you injected power from/to? Would be great to have this documentation for people working on their houses with these lights. I have a 200ft kit. and I just got support to respond to my plan where they say "Yes its possible": I want 50ft of lighting, 24 ft of extension cable, the Govee driver module, another 25ft extension, and then 100ft of lighting. Theoretically, this works. but your power injection and Y split videos give me hope I could run cable differently. Thanks again for all the work!

Hello Chris loved the video by watching your videos I just bought 15meter 5v ws2821b and esp32 for my room but what I can't figure out is how much power do I need. Please Help

Chris I said it once and I'll say it again you've been my favorite channel since I came across it. I watch your videos all the time and it's made me a better contractor. I understand I am not a licensed electrician but I do have a HICL I install Permanent Lighting I'd say as a career now. I wouldn't want to take the shine away from the licensed electricians out there so I'll say that again - I am not a licensed electrician - I just wanna ask, at what point do you think the line is crossed when going from DIY to Electrician work when doing this as a career? As soon as you make the 1st cut into the wires and do any sort of modification? Ik your channel is a DIY channel not intended for commercial use. But I'd probably state that in your videos. I always think God forbid something happened with a bad connection I made and now I have lives at stake and me and my company were the last ones on that property. Not saying you're doing anything wrong either tho. I just do this as a profession now but also don't want to break any rules considering it's been going very well for me. Anyway, you're the fucking goat and I always enjoy watching your videos, always, please don't stop what you love doing. You deserve everything you ask for and I hope nothing but the best for you and your family bro. Keep being an A1 dude and 1 thing I wanted to mention: you're usually out of frame in your videos, so the 1st time I seen you in your video it was funny idk why 😂😂😂 like holy shit there he is, the man behind the camera ... idk not making fun or jokes it was just funny. Keep killing it dude and I've said this before too, you've inspired me to keep pursuing this shit. - Ed, Absolutely Dialed Pools, Absolutely Dialed Graphics 🦖🦍🦄🦈🐙

I have the 150 ft GOVEE (comes with 2 12 ft extensions). I am planning on using just about all 150 ft but planning on splicing multiple areas with smaller 4 ft runs to hop levels. I wasn't planning on using the 2 extensions but using 16/3 wire for small ones. Do you think this will hurt my build? This video has me a little worried now.

I used 18 gauge copper wire and cabt really push far. Is silcone wire better for these lights?

Are you using the same power supply? Or you did use a different power supply for the injection as im having this issue with my 150ft govee light

Tnk u broo. Please 🙏 Can I extend the control module "the controller" in order to put it like a switch on the wall? To make a chain between the controller and the strip? Thanks in advance. I use rgbic pro 20m

Please help!!! I connected 11 strands together on the 150’ Govee kit. The last two strands don’t light up. What can I do to fix that.

Does splicing a set of 2 leds and connecting them back in reverse order cause any issues?

I installed a set of the new pro lights today. We used all but two segments. Even without using two of the segments, the last two segments are flickering. I'm hoping it's just a bad connection. None of my jumps are really that long. But if I have to inject power, does it have to be from the same initial power supply or can it come from another power supply?

What if you had a spare power supply from a second kit? Could you use that instead of a jumper?

1 have (3) 24ft COB LED light strips that are all connected to a 24v power supply. They all turn on but the color changes as it gets further away from the power source. But oddly only when i try to do a "white" color or some variation of white or yellow. It goes from white to almost orange at the end of the lights. Is that a power supply issue? Been thinking of connecting all these lights to that already WLED loaded purple little thing that you made a video about. Would that work?

any idea how many strands/ feet of lights you could safely utilize injection from one power supply ? Say I wanted to use one power supply for 600 feet of lights. TY in advance.

Dude this is so awesome! Thank you so much! Question though, can you just run the power injection to the end of the last light instead of the beginning of the second to last strand?

How many volts do the LEDs need to work? The power supply produces 36V, but by the end of my third strand I am reading 34V and the strand doesn't light up at all.

HEY CHRIS IM HAVING TROUBLE WITH MY VERY LAST STRAND..... I HAVE A 150' SET AND HAVE ALREADY USED BOTH FACTORY JUMPERS. I HAVE A GAP BETWEEN MY 6TH AND 7TH SET OF LIGHTS THAT IS ABOUT 18'.... ARE YOU SAYING THAT I NEED TO RUN THE TWO "BOOST CABLES" FROM THE FIRST SET OF LIGHTS TO THE SEVENTH SET? IM ONLY GETTING 2 LIGHTS LIT UP ON MY 7TH SET WHEN I HARD WIRE THE 6TH AND 7TH TOGETHER. PLEASE HELP. THANK YOU

How is it a solution to power inject from the power supply all the way to end of the strips? The distance demonstrated is also only a few feet.

Where did you get the injectors?

Hi how can i use ws2811 with esp32

I cut a section and than added a 10ft section of wire but than no power to the sections after the cut and the last few lights before the cut only stay on with a white wont change colors. What can i do to fix it.

Chris please help me. I’ve tried following your 50ft led video and I’m losing my mind.

So the solution is to power inject all the way from the first strip to the 6th?

My flickering has gotten worse. First it was only the last string of lights, now its the three last strings. What could be causing this?

Dude, in one of your old vids (the one with wled i think) you mentioned that the wire with black on the back is negative....now is positive ??? I wired mine today with the black lines as negative....😅 they still work tho 😅

Instead of injecting at the beginning could you inject at the end of the 7th string for the same effect?

i understand a lot about a lot of things but no matter how many times it's explained to me I'll never understand electricity 😞... fun watch though👍

On mine the black line is on the middle wire not the bottom 😂 I have something rigged up but I'm afraid to try for fear of shorting things out

I am trying to add leds to a brick retaining wall, I am running into all sorts of aesthetic options, first is I am seeing the individual leds (60/m) when looking from the side, how do I hide these? I don't need to fully difuse them and I also have a curve that aluminium channel isn't a good fit for.a Also, do you know of any RGBWW IC controllers that have google home integration? I can't seem to find one. I can find the strips (SK6812 or WS2811) but can't find a good controller... Thanks!

I want to run more than 150ft of lights on the same controller. What power driver should I use for power injection?

The worst flickering I get is because the power here is very dirty. AC bulbs flicker regularly, electronics connected to mains can die, and any LED powered by a regular power supply will flicker as well. Important things are plugged in to line-filtering UPS units, but I’m still on the hunt for the equivalent in 5v and 12v power supplies so that none of my LEDs will flicker any more.

Second comment

Does splicing a set of 2 leds and connecting them back in reverse order cause any issues?