Problems Spraying With Your Graco Magnum X5? Graco Magnum Troubleshooting Guide

Подписаться 9 тыс.

Просмотров 49 тыс.

50% 1

Having problems priming or spraying with your Graco Magnum airless sprayer?
Follow this simple guide to help identify and troubleshoot any issue that you might be having with your sprayer.
00:00 - Intro
00:20 - Pre Troubleshooting steps
00:46 - Which Magnum Units
00:56 - What Tools are needed
01:24 - Step 1, Outlet Valve
02:44 - Step 2, Inlet Valve
07:04 - Outro
Graco Magnum Range
► goind.com.au/collections/magn...
Lightweight project sprayers - goind.com.au/collections/magn...
Midsized project sprayers - goind.com.au/collections/magn...
Major project sprayers - goind.com.au/collections/magn...
[Article] Airless Spray Tips Made Simple - A step-by-step guide to choosing the right spray tip
► goind.com.au/blogs/articles/a...
[Video] Graco Magnum ProX17 Paint Sprayer
► • Graco Magnum ProX17 Pa...
Connect with us
Website ► goind.com.au/
Instagram ► / go_industrial
Pinterest ► www.pinterest.com.au/go_indus...

Хобби

Опубликовано:

10 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@alexisdiaz6137 Год назад

I couldn’t fix mi e till I find you video ! You the man!!! Thank you !!!

@GOIndustrial Год назад

Glad we could help!

@diazedvin04 Год назад

Thank you bro! I have my x5 working back again

@juba-9042 3 месяца назад

Thank you, it fixed the issue

@vjhuerta81 Год назад

great video !! right in the point very technical and good breakdown 👍

@vjhuerta81 Год назад

mine wouldn’t suck the clean water while priming havent used it in a while so all i did it hit soffly in the metal valve and worked right away so great the ball was probably stucked

@armanm5465 8 месяцев назад

Thank u buddy it helps me lol 😊

@probuilder961 2 года назад

Nice video. I have a year 2000 Magnum XR7 sprayer with no more than probably 40hrs on it. I can't get it to prime. I'm doing this with water for starters. The pump runs & prime/spray valve is set correctly but it only sucks water to top of filler tube and no further. I watched Graco's failure to prime troubleshooting video and checked all the filters, inlet valve etc.. I even tried power flushing it. Funny thing, my inlet check valve has a ball & washer but no spring.

@Juanesverde33 Год назад

Perfecto 👌🏻 Thanks You

@LeslieWood-qb8do 6 месяцев назад

Thanks 👍

@henleyont Месяц назад

Great video. But how to free the pin if seized, like I have, obviously caused by not cleaning properly.

@ernestovazquez9517 Год назад

Thanks for the videos. The problem that I have is that the spryer pops the Circuit breaker when it's turned on. It all started when I was priming the machine for cleaning the breaker popped please help

@jragster Год назад

Thanks

@djbosox Месяц назад

I have a refurbished X5 that I bought about 9 months ago. I just tried using it this weekend. It primes just fine but when I switch over to spray, it makes one little noise and then nothing. No spray at all no matter where I put the pressure knob. I tried it last weekend, cleaned it up and tried again this weekend and nothing. When I take the spray hose off, nothing is in it. Any suggestions?

@Texasknowhow Год назад

My graco machine is running non stop and with tons of pressure at the gun. There is also some paint by-passing through the smaller exit tube back into my paint can. Shooting interior latex trim paint. Is it not sensing the pressure at the regulator and just running away with itself?

@Johnsrt2023 2 месяца назад

Hey man mines doing the same plz help!!! Haha. Did you ever figure out what it was doing??

@karlaelvis9815 2 года назад

Does the Graco Magnum DX also allow for the inlet valve to be removed? I can prime my unit but when I switch to the paint bucket, depress the trigger, and move to "spray", the pump immediately cuts out. All screen are clean and I have a new tip. I watched your video and went to clean the inlet valve, but I can't get it off... I can use a "cheater bar" on the handle of my socket wrench, but I don't want to break something if it isn't meant to come apart - thanks! Great video - I learned a lot.

@daniellegarrett4130 2 года назад

Same thing happening to me

@kathleens6770 Год назад

Ditto. I also can't get the inlet valve off.

@patriciar7202 Год назад

You mention “cleaning it up” … what would be best way to do this? Would a wire brush be too abrasive? Or soak + clean with a specific type of cleaner / solution? Thanks in advance, and thank you for the great videos!!

@GOIndustrial Год назад

Thanks for your comment! Definitely a mix of a soft bristle brush, hot soapy water and thorough flushing of the machine is the way to go. Hope this helps!

@OfficialTuneIn 11 месяцев назад

is the o ring necessary?

@gilhoi 2 года назад

How are you cleaning this parts? And are you lubricating it? Thanks

@GOIndustrial 2 года назад

Hey, great question! I would typically just soak the parts in a white spirit like methylated spirits and then use a bottle brush to brush debris off the parts. I would then rinse them under water and install them. When you prime the unit with Graco Pump Armour that will lubricate the internals. Hope this helps!

@MrC9Oh3 4 месяца назад

Does his pump have a filter?

@descimalowe4144 Год назад

Power coming to sprayer but it's not coming on

@bobpboston 5 месяцев назад

I'm trying to troubleshoot a product that has its vids here. Does RU-vid really believe I wan to sit thru minutes of crap adverts first??????

@GOIndustrial 5 месяцев назад

Ads like this do help the channel, and allow us to make more videos for troubleshooting and giving out this advice to save you money from taking it to a repair centre 🤝

@phantomxmods3095 Год назад

After 25 minutes of spraying for the very first time worked great, got 2 ceilings done and moved on to 3rd, halfway through the pressure went out on my gun. The Magnum X7 wouldn't suck paint, motor just ran....went through 2 hours of videos, followed all the steps and no help. New paint, new machine, parts were all good to go, not sure why it just stopped working??

@maribelramirez4545 Год назад

Any luck with it?

@phantomxmods3095 Год назад

@@maribelramirez4545 No, was told by Graco to take it in to be serviced...as soon as I find the time...which means I'll never get it fixed and just end up buying a new sprayer.

@MyKonaRC Год назад

Be a man and put the machine upside down when reinstalling the spring and ball! My god dude! "Get your dinky punch to help line up the spring and do this sideways...."