No video :(

Pt.2 ATV CV Boot Replacement At D-Ray's Shop

Подписаться 44 тыс.

Просмотров 361 тыс.

50% 1

All modern ATVs use CV shafts in one form or another, this Yamaha 660 Grizzly has a total of ten! They are easily torn, and if left un checked will ruin the CV joint. They are not hard to replace, as you will see.
Thanks for watchin' Don't miss Parts 1 and 3
I created this video and I own all rights to all content in the video.
Music provided by : Kevin MacLeod incompetech.com...
Name of tune "Cold Funk", and "Delay Rock" Kevin MacLeod (incompetech.com) Licensed under Creative Commons "Attribution 3.0" creativecommons...

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 95

@KimCook-cd1fs 3 года назад

Ray, you did an excellent job of how to, from start to finish

@BWWGL9 7 лет назад

Thanks D. RAY,,,,,,,, very professional presentation, without all the UNNECESSARY ANNOYING MUSIC.... I can hear you clearly and see what you were doing.

@darthnatas953 Год назад

As far as I am concerned, you sir are a frickin surgeon.

@palmettofarmer 8 лет назад

Mr. D-Ray....I found your instructional very informative and easy to follow along. Thanks for such a positive attitude and enthusiasm that makes you listen even if you don't have a project. Enjoyed sharing with my 17yo son without tensing waiting on the next group of curse words to being blurted out. Great work! 5 ☆minimum, more like 10!!

@palmettofarmer 8 лет назад

Where do your recommend buying Honda ATV parts?

@chocolate_squiggle 2 года назад

If you're worried about your 17yo hearing curse words at that age you're setting him up for a lot of bigger problems later on in life.

@johnsmith-qh3vq 6 лет назад

perfect I like the whey you show every step. thankyou very informitive

@susiehill7316 25 дней назад

Great tutorial. I just replaced my axle cause I did t know how to do this. Could’ve saved a pile of money

@scottmccormick2565 Год назад

Great vid D-Ray.If you teach Gods word the way u explained the cv axle repair oh boy.

@mikviss5711 8 лет назад

D-Ray, great video… very helpful Thank You!

@user-rv1he6vt4c 6 лет назад

That's what the doctor ordered! Thanks a lot for your sharing.

@garyclagett1848 5 лет назад

Great video build of the cv boot repair! Your instructions are clear and understandable, thanks!

@eclipser2004 6 лет назад

Great and helpful video. I would not reuse either boot if I went through all that to take it all apart. I figure if one boot is gone the other must be close to going.

@Joel3436 5 лет назад

not if you ripped it on sticks

@furfeelings 11 месяцев назад

Same here! If I'm going that far it'll all be new when it goes back on!

@timjones1878 5 лет назад

Great video!! it really helped me replace my c.v. boot's..would have been tough without your help..thanks..

@franksenter9838 9 лет назад

Other then some difficultly removing the inner bearing without use of vice, all went well. Great demo! thanks..

@MichaelAyers-jj9hx 4 месяца назад

Thank you. You make it look easy!

@davidgower6170 10 лет назад

Top notch vid, many thanks

@FlightSergeantRose 8 лет назад

Excellent video. Everything is explained quite well.

@insaneasylum7898 4 года назад

Excellent job explaining everything in detail. I'm hooked

@derekperkins4420 8 лет назад

thanks Jason , that was very helpful because I am working on a Yamaha wolverine right now.

@rustycherry12 3 года назад

Best video on this subject... thank you!

@wademoulton5109 4 года назад

Thanks great video. I wish I could understand what made 44 people dislike this video. How can you dislike something made to help people.

@aristofilosa9854 8 лет назад

thank you D-ray ,it was very helpful your video !! i have SYM 600 quadrider i'll use your informations ....

@Ranger42 6 лет назад

Like the fact that you started working on a clean ATV with no mud or dirt on the axel as it makes it so much clear for us amateurs to observe and learn. One Q...what did you use to remove and clean old grease?

@jchefboyardee 3 года назад

Very informative and attention to detail video! Thanks

@michaellight3060 6 лет назад

D Ray, i just pull the bottom shock bolt and the bottom knuckle nut then the axel comes right out. Alot faster

@JasonBreeland 6 лет назад

These videos were so much help. Thank you for sharing!

@fredanderson1753 8 лет назад

Excellent attention to the details...Helped alot, Thanks

@franksenter9318 9 лет назад

Honda Rancher, 2010 front axle. Can't remove or slip the beirngs race off. Pounded it with a 2x4 with no luck.

@2499Michael 4 года назад

Thanks mate! (from Australia).

@johnhenderson299 2 года назад

Super great video

@maquisard2b266 5 лет назад

Thanks a lot from France, i was very interesting by your movies. instructional are very informative and i can do that now on my engine. thanks for your time to make that.

@nathansanders9559 8 лет назад

great video. very good on the camera.

@cordchoppers8202 4 года назад

Your Videos are always Super Helpful Keep up the Good Work 👍 Cheers 🍻

@zx8401ztv 11 лет назад

Looks like a brand new one now :-) Nicely done mate :-))

@trikerjon 3 года назад

Great instructions , thanks 👍

@kbro7484 7 лет назад

Why worry about if you get grease on the inside of the boot. The grease will eventually work it's way off where you placed it and onto the boot?

@nightrod2237 5 месяцев назад

Thank you

@brockoleary8377 10 лет назад

Great Video thanks D -Ray!

@Cj-ph2ky 8 лет назад

Very nice instruction. Thanks!

@point223 8 лет назад

Awesome Video D-ray. I have a torn boot and the cv started clicking. How easily are the CVs ruined? is it something you can clean, regrease and reboot and be ok or is the cv ruined pretty quickly if its not taken care of immediately? Great Video by the way. You do a great job explaining all the little things to look for when doing this job. Thanks

@ezechielroy859 3 года назад

this video is very great ,thanks man.

@royfoley2591 Год назад

Ray, How is it your inter joint race and bearings stayed together, my ball bearings fell out all over the table when I removed them from the inter joint cup.. what did I do wrong ?

@DOMINION4x4 6 лет назад

Thanks for such detailed video

@gordonwoodson6921 5 лет назад

Awesome video!

@sugargoldy 6 лет назад

Excellent video sir thank you job well done

@Smngorin 7 лет назад

Thank you! I'm definitely subscribing and liking this video.

@adamj1168 9 лет назад

Fantastic videos, man!

@MrTexaspete30 4 года назад

Thank you for the video good sir

@stricklandxmr190 3 года назад

Can someone tell me if it matters how the c-clips are facing

@riv1950 7 лет назад

Very good video, thanks.

@Gunnypauly73 4 года назад

THanks Man , Great video

@cardinaldom574 5 лет назад

Please, can worn-out or bad inner cv joint cause ABS light on? I asked because immediately I changed the cv axle joint, I began to hear like cracking nose. Please, what could be the problem?

@nathanmorris2029 4 года назад

Good video man

@judyhile8551 3 года назад

are there after market cv boots for Kubota RTV x 1120D If yes, where--thanks for excellent video

@hannahkiesling6907 8 лет назад

This was very helpful Thanks

@hrivera929 8 лет назад

Great video !!

@dianeconnell5111 10 лет назад

It appears our bearings may be toast. They are falling out of the chase, or is this normal?

@jaredsingleton9611 10 лет назад

How do I get the cv axle out of the rear plunging joint on a 2003 Polaris Sportsman 700 Twin? There's no retaining ring, and it doesn't seem to rock far enough to release the balls.

@alimashaaleh7980 5 лет назад

thank you so much

@jeanmimeault6936 7 лет назад

Excellent!

@rubendario7441 10 лет назад

super bueno el video asi es que nesesitamos un profesor

@edwardguinn332 8 лет назад

thanks for putting out the video ... ! question got a catvo 6 inch lift eagle turner axles cv boots getting to hot destroying the boot is there better grease ? or can I simply put in more grease ? any ideas ? again thanks for the video

@gooddrugsfarm9105 6 лет назад

Dude you rock! Thanks!

@Sparkynutz81 10 лет назад

Didn't look like you got clamps very tight. Know wonder they spin if grease gets on them

@armedfarm3429 Год назад

Thats right. I noticed it also, need to throw them into the garbage for one thing & get the notch clamps. I would & have used 75lb zip-ties many times, much better than these pull through & fold overs. He at least should have pulled them tight with a vice-grip then fold.