Put Aluminum Foil on Led Bulb Brightness Will Increase 100% 

New generation clickbait

Do the smart thing and use solder. The graphite will cause resistance heating. The alunium foil will break down and possibly catch fire.

The scares on the left hand of this dude indicate where his way of solving problems leads. I am surprised that he still has both hands.

This is pretty unsafe. Led Bulbs do in fact get pretty warm. The normal heating and cooling cycles when used will break down the adhesive of the tape and it could lift, weakening the aluminum's connection. Now what you have is a small pocket of hot air with kindling (the paper) and an ignition source, the electric arc from a barely touching tinfoil connection. Surrounded by plastic which is most likely flammable. Fire takes 3 things: Heat, Fuel, Oxygen. (a spark creates enough heat to start the process). The graphite seems better, but not much... for the same reasons. Solder it!

The load will increase on the rest of the remaining worms, and they will burn one after the other... It is a temporary and non-permanent solution... Thank you..

Никогда не лезьте во включённую лампу неизолированным инструментом - Вас может запросто убить электричеством, хоть напряжение на одном светодиоде и невелико, но так как источник питания в лампе не имеет галванической развязки от сети 220В, то Вы можете попасть под потенциал сети.

It s like telling people they can learn to fly by jumping from a bridge...

Harmful video, nice time catching fire. 👍

But removing one or more LEDs will increase the current in the electrical circuit, which will soon cause other LEDs and other components to burn out. The correct thing is, if you need an LED lamp with more brightness, buy another one with greater power. Só que retirando um ou mais leds ira aumentar a corrente do circuito elétrico, que logo mais vai causar a queima de outros leds como também de outros componentes. O correto é, se necessita de uma lampada led com mais luminosidade é comprar outra de maior potencia.

i find that sticking a fork into the socket also works well.

For the brightest effect, the foil should be wrapped all over the screw of the bulb

OK. This might technically work. But be aware that depending on the lamp design you may risk to get an electrical shock that may kill you! This should only be done by people that are aware of the danger working with electricity. If you ever do it it would be better to replace the burnt out LED by one of the same type. And even though I like the idea to save money and produce less waste it might be better to spent $2 for a new lamp. That's much more environmental friendly than a burning house!

Looks a great idea. Ihope it really works👍👍. But I will use solder. Corr the amount of bulbs I’ve thrown away.

And while your house goes up in flames you smile because you saved a bunch of bucks on a light bulb.

I've been getting my LED bulbs to work again the same way. I got the idea from the Christmas lights that failed in the same way back in the day😅. Leave the cap off so they don't overheat tell everyone to keep their friggin hands away from them. They all still work many years later.😮 No problem I'm just getting my money's worth😂.

Licking the diodes whilst plugged in also makes it brighter.

doesnt make the bulb brighter... this is just a how to fix a broken led lightbulb. smh

Hot damn! I just this minute tried it and it works completely. But I think I'll go the way of solder instead of the foil. THANK YOU FOR THIS FIX!!!

Learn how to solder! With aliexpress it's never been easier to invest in good soldering tools, and learning how to solder is a ton of fun.

Dude could’ve went to the dollar store and gotten a new one for the amount of time it took 😂

use a resistor or they will blow even quicker as they are in series. When he says increase brightness by 100% it's because they go from not working to working lol. Use a resistor or another led. Problem is the heat sink it's not easy to get enough heat into the board to solder them due to the built in heat sink or ground plane.

I still find these sort of videos, useful, and entertaining in the sense that even a partially good idea can help save your ass in a pinch, especially on a busy movie set. So while I agree with the general sentiment on here, that is being put forth by most of the residential electricians: (Recoiling in horror that someone would hap-hazardously modify a lightbulb for installation : (potentially in someone’s household without their knowledge or consent) When your job description specifically calls for “quick, dirty, creative yet EXTREMELY TEMPORARY engineering “ - SOME of these tricks could save your whole career when you manage to “Save the Day” : AGAIN!!!! Cheers, SIXSTRINGSPACEBOY

Every light has it's unique look n rich lighting

والله انك شخص راءع سيدي شكرا لك

Instructions unclear. Facing multiple arson charges.

The LED connection is in series if are going to short the busted LED the good LED will overload. Correct me if i'm wrong

Видео неправильного ремонта. Правильно это надо паяльником припаивать новый светодиод

你要用鉛筆的鉛來做 導電目標 久了也是會因高溫而脫落(用錫箔紙亦同)，用錫焊接不是更好!最好的方式還是買相同 燈珠 做更換壽命才長，要不然其他 燈珠 受電增加，整體燈珠壽命也會跟著縮短~

С синей изолентой можно было даже фольгу не подкладывать. С синей изолентой все работает! 😂😂😂

save yourself time and just go buy a new bulb with more wattage. Good lord.

Good video, but misleading thumbnail

it's not a good solution, because this way the other leds have a higher voltage and thus the others will be destroyed sooner.

The last time I used pencil lead as a conductor I was in prison!!! And that was to make a lighter. I am not saying it can't be done, what I am saying is,why not just use some solder and repair the light a more effective and efficient way? Solder would be the absolute right way to go for this repair.

why not just replace the led?

current limited at the DC convertor chip.......the Brightness of each LED are no change

This looks completely safe…

THIS ISNT HOW TO MAKE THEM BRIGHTER THIS IS HOW TO FIX BROKEN LEDS

LED칩을 교체하고 납땜 할거라 생각했더니 그냥 포기하고 은박으로 붙였네요. 잘했습니다.

The rubber tape will melt and fall off. The current through the remaining LEDs will increase and the will burn out.

The heat will reduce with every smd until your more in the dark every failed smd. How do we restrict heat without R 10 ohms ?

How to burn your house down with graphite and tin foil modifications to a cheap light bulb. Yeah, I think I got it now... Thanks.

It's not 100% brighter if you remove one of the COB elements 😅

To add radiating aluminium particles are the biggest cause of cancer. Please research further.. also can correct me if I'm wrong. Thank you..

Do the smart thing and go buy a new $2 bulb ... how cheap are you? Something like this is what intelligent people call "a fire hazard waiting to happen" ...

You will get a free light show if you screw a ball of foil into the light socket. Dumb people: if you havent burned your house down yet, dont try this its a joke.

recipe for fire in your house?

bord ısınınca bant gevşeyerek devreyi keser. board gets hot and tape loosens and it cuts off

This just means they are going to blow even quicker. If you are going to try it this way put a resistor in.

Awesome idea to cause fire

considering the price of these bulbs it’s not worth the fire risk.

....I'll pass, i don't feel like setting my house on fire today.

Человечество давно создало паяльник. 😊

Hope everyone is doing good and staying safe

Regardless, these things are theown away i. Masses because they are not easily servicable. Responsible production needs to be enforced. Too much wastage is going on for corporate greed

It was a great fix until my house burned down.

Синяя изолента - это то что надо!

olá bom dia parabéns gostei muito Eusou Antônio de viçosa Minas Gerais

Dont mess with live socket voltage

I'll just go with a higher lumen bulb for an extra couple of bucks.

Forgot to put on tin foil hat

You just put it on OFF. 100 % Result !!

Just buy a new lamp. You will live longer 👍

This is why removing the dislikes was a bad idea.

The thumbnail😅😂😂😂

Bro don't use the graphite method. Just put some solder on it.

Bravo..bravo..BRAVISSIMO😂 CIAO

Thanks my house is on fire. But at least it's pretty bright here now.

Totally nonsense solutions with graphite and aluminum foil. Solder both ends instead

Độ sáng thì phải nói là sáng hơn nhiều nhưng độ bền thì lại giảm xuống cũng k ít. Nếu làm như vậy thì thắp sáng đc mấy canh h là bị cháy thôi à. Vậy thì sáng hơn để rồi vứt thì sáng hơn làm cái gì chứ😅😅😅

The thumbnail lied to me.

If you remove 1 led bulb from series after someday another led will burnt

Very unsafe. PLEASE DON'T DO IT. Could burn and happen a disaster.

Look at how burned up the inside of his left hand is on the second segment…

I do not understand why you do not use soldering iron. i repaired my bulbs always but i see this video. what for you trying with pencil and aluminium? go solder it.

Why not solder new led in 🤔

Ok good trick but looks pretty unsafe but my question is, how does this increase brighteness 100%????? Clickbait or what!!

i hear you loud and clear

This might cause fire.

more current for the remaining bulbs-If overload led life is reduced.........

Wouldn't it be cheaper to buy a new bulb?

Do try this at home

1D10T !!

All he is doing is just increasing the current amount. He will be paying more money now!🤔😜

You know what; to hell with all that. I've got a few bucks, I'll just go buy a couple of new ones. OK...?

Just buy a bulb with higher wattage. Who has the time for all of this?

If you don't want your house burn down, don't do any of those craps. put a new bulb in.

best way is solder it, this is so stupid

Nice work. Thanks.

А если убрать два светодиода то яркость увеличится в 200 раз? А если три? 🤯 А для увеличения яркости если нужно то можно просто снять колпак.

Неужели вы не можете купить новую? Всё они одноразовые и тратить время неразумно.

LED драйвер ограничивает ток, даже, если останется лишь один светодиод, он не перегорит от якобы перегрузки, как здесь многие пишут. Нагрев драйвера возможно увеличится, и только.

i can feel how it murders eyes

Most graphite in pencils will not do what is claimed, though it could act as a resistor if there is enough carbon content. Note that doing it live is EXTREMELY dangerous as some LED lights have mains voltage across the LEDs. I would definitely NOT Follow any advice is this video. It's too dangerous. LED globes are cheap enough to just replace if they fail, or if you know what you are doing, properly solder a resistor in place to bridge a failed one. If you do what is claimed in this video and manage to get it work, well just remember the carbon poweder from a pencil just falls off and because no connections are soldered, they will fail very quickly, if they work at all to start with. Fire risk is very high

All the time and effort into 'hacking' that bulb, just to kill it faster, I could have gone to the store and back in screwed in a new one for less cost...

you have shorted out this one led, the others will overheat very quickly.

Tape got hot, dry up & fall off

Just buy some solder

Is people's safety less important to you than view count!?

No time for Thomas Edison work!

this is some major click baiting, not to mention that methods used are extremely dangerous. I highly a browser ex called DeArrow. It combats these click bait channels by allowing users to change the title of videos to something more accurate, and also allows users to change the video thumbnails to something more appropriate. Anyone else with the ex installed can then see these changes, and make a more educated decision on whether the video is worth watching or not.