Quick Look: Precision 6.5 Creedmoor Reloading Start to Finish

Подписаться 358 тыс.

Просмотров 189 тыс.

50% 1

Please consider supporting Ultimate Reloader on Patreon: / ultimatereloader
-------------------------------------------
Important: See disclaimer at end of video description.
-------------------------------------------
Full Story: bit.ly/2EcNPZD
As a part of a series loading 6.5 Creedmoor using the Forster Co-Ax press, this video is a condensed view of the entire precision reloading process. Be sure to catch the next story in this series: 10 shot load development- be sure you're subscribed!
*Note: L.E. Wilson suggests that you trim brass before priming for safety reasons
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this RU-vid channel (gavintoobe).
Any reloading data supplied on this RU-vid channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this RU-vid channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this RU-vid channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this RU-vid channel (gavintoobe) or in this video.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- Hornady
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: ultimatereload...

Опубликовано:

17 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 132

@dragmorian6347 Год назад

Dude, I’m just getting into 6.5cm loading, and this was super helpful. Been loading 308, 556, and 300blk for years. But, somehow, I was really misled by friends on the 6.5. Thanks a lot for the tips

@gary5051 6 лет назад

Thanks for the video...I assume you'd tumble the brass after sizing-especially since you lube'd the inside of the case neck. I know its a very broad overview but seems like all the key steps should be mentioned. Controlling headspace, neck tension, and concentricity could be mentioned but not shown. Same with less universal practices like annealing, neck turning, etc. This would be valuable to someone new to reloading. Thank you!

@charlesgutzwiller5988 2 года назад

I tryed going up the powder scale to find my nodes . I just returned from the shooting range for seating depth .man that system works great I'm a beleaver! Great info .

@dghboy315 6 лет назад

Thanks for doing this video. So great to see the entire process.

@Ultimatereloader 6 лет назад

dghboy315 you are welcome!

@Chris-tw4jm 6 лет назад

Awesome video! Cannot wait to see the ten shot ladder vid!

@kevinjoyner9755 6 лет назад

just a little tip. For those who use presses and separate primer tools, Using a small magnet with "L" or "S" stickers helps you remember the last configuration of the press or tool. Great for those who use the Forster Co-Ax press which has "S" and "LS" plates with small and large ends.

@leroyjenkins1511 6 лет назад

I always place my loaded rounds in the LE Wilson case gauge to double check sizing to ensure the rounds will chamber. It is a must to reduce feed issues.

@Ultimatereloader 6 лет назад

Leroy Jenkins cheap insurance!

@Jeff_Seely 2 года назад

Lots of medium-high-end goodness on that bench. LE Wilson is the best at what they do and they are certainly aware of that. Buy once, cry once and you can't go wrong with this set up!

@leefeatherston7014 6 лет назад

good video 👍 can't wait for the shooting test now that is a great press

@tomlarue654 2 года назад

This video is very helpful. Thanks.

@neilharris4462 6 лет назад

Im not sure if you've ever wondered why primer companies store their primers isolated in the package, but dumping them all into a bin like that is asking for issues if one was ever to detonate.

@jeffreyvictor3678 6 лет назад

Always great info and video!

@The4GunGuy 5 лет назад

Man, I'm getting ready to reload my 6.5 creedmoor and so glad I found this basic video of yours...concise and to the point. You primed, then trimmed, is it OK to trim THEN prime? On to your 10 shot load vid!

@jimbeeler9471 6 лет назад

I have always prepped the case (sized, de-prime and trimmed) and THEN cleaned it to remove all traces of lube rather than cleaning, lubing and loading. I'm interested in your comments about going about it in this order rather than the order you're doing it.

@nunyabisness4300 10 месяцев назад

I’ve never reloaded but really want to and your method makes sense to me.

@dirtmerc8511 5 лет назад

How much did that whole setup cost? Thanks

@johnwallace1729 3 года назад

Less than buying loaded ammo if you are into shooting . That forster press is slick no threading and turning in dies ,nice .

@zrbsrbija 3 года назад

About 1200 doll

@JimmyMakingitwork 3 года назад

Wish I would have picked up some of these supplies a year ago. Feel naked.

@adelmomew 3 года назад

Exactly, once this is over i will imvest about 4k in equipment and supplies, my coworker says pre corona his 556 rounds came about 10c a round

@derekkonosky3559 3 года назад

Would have been nice to see all the steps from a fired case to sizing. What do you do for brass prep in those steps?

@marcoscancel7693 4 года назад

Hi! I’m a fan of your channel. Recently reloading 6.5 Creedmoor for my Tikka T3x Tac A1, but have a fundamental question, primers. It’s kind of a split opinion on large rifle primers going cci250 VS cci200. What’s your opinion? Recommend Magnum on some powders?? I’m reloading 123, 140, 147 grains and have R17, Hybrid 100, H4350 and Superformance at home. Kindly appreciate your expertise. Keep up the excellent work!!

@breakintips9896 4 года назад

Marcos Cancel I have the same question. He’s not the only reloader that went with a small primer. I wonder why? All of the factory ammo I’ve looked at all has large prime. I see you are using cci primer. Isn’t that like a military grade primer that is a bit hard to prevent bump fire? Is there any advantage of using a hard primer? Thanks

@richiejohnson2743 4 года назад

Any responses on this? ALL the guys I know that shoot and home load 6.5 use the Lapua small primer brass.

@johngeddes7894 Год назад

Small primers are safer, and originally, it was recommended to Hornady to go with 58,000 piezo pressure, but they went with 62,000, knowing absolute redline was a little over 63,000. That’s why some want the small primer, but in cold weather, there are known failures with the small primer. The best solution would seem to be a slow burning powder, like H4350 or similar, with the large rifle primer, and going conservative with the charge weight in grams. Start with minimum and work up slowly until good accuracy or max load is reached. There is a favored distance off the lands, maybe .040”, but it varies from each barrel and chamber.

@frankjohns2892 Год назад

Hello community, Gavin, another awesome video. Thank you. I've watched several videos by you, as well as others. I think I'm ready to start reloading. I own several handguns and rifles that I want to start reloading. It appears the steps are the same however, where is my best source to find information and supplies? For example, I own a 6.5 PRC and I know there are differences between Creedmoor, PRC and Grendel. However, I don't really know the differences. I just know I was told, "Oh, make sure you buy 6.5 PRC because it is different." Any pointers are welcome. Thank you.

@rossvanderpoel3907 6 лет назад

Idea: CBTO process for bullet jump into the lands. I.E. a distance from/to the lands video with an explanation of why this might be good for precision re-loaders. Bullet Comparator demonstration.

@axeljehovanymendoza 3 года назад

What parts where used for this reloading setup. I would love to produce the quality you just produced.

@bigdaddyrichie88 4 года назад

Can you give a list of all the equipment you had here to reload

@brentfrank7012 3 года назад

Exactly, now go through that equipment quickly and help us build a shopping list and budget.

@i556xx4 5 лет назад

That seating die did not leave a ring on the bullet? I just reloaded my first round today and my rcbs die left a ring on my 140 GR eld. I only assume it will be worse with 147gr elds.

@michaelugarte81 5 лет назад

Do you have a video on bullet seating depth for 6.5 Creedmoor or any other caliber? I would like to see a video of the do’s and don’t to get the bullet close to the lands.

@Jdsnipe112 6 лет назад

Why would you put primer in before you prep case you could get brass chips in it.

@jaywhat8126 4 года назад

Josh Davis Why would do a lot of the things shown here?! Priming before the case prep is done (including getting that lube off and out of the case?!) 🙄 ... yes, I know this is an old vid.

@RetrieverTrainingAlone 3 года назад

I'm old school...I hand load for bolt action hunting rifles with a 1972 RCBS JR2 single stage press. I use RCBS case lube and pad...been using that for over 30 years and never a stuck case....why is this no longer popular for case lube? Would you get a more precise neck by using an expander mandrel instead of the expander ball in resizing die?

@joshuaingle5557 2 года назад

Hello. Great video. I am wondering if you can provide a link to everything you have here on the table. Thanks.

@Kurzwilde 3 года назад

A lot of us aren't too sure where to start, is there a forum or somewhere that lists what is a full set up? Love the videos great content!

@johnsterling1912 5 лет назад

Great video! What is your exact setup? I'm getting into reloading. Just picked up a 6.5 savage arms axis.

@johnwallace1729 3 года назад

The Axis shoots

@franciscoortiz9730 Месяц назад

I got a cartridge stuck in my small base die. Am I not lubing enough?

@rumplebumpy1330 Год назад

Are you using a bushing for the micrometer seating die? If so what kind?

@larrywhite3786 Год назад

Never seated the primer!

@bogaudette6227 Год назад

I have a .260 browning A bolt micro hunter. The gun has a 1in 10 twist. It shoots factory loads Remington core-lokt 140 grain really good. I had a friend of mine load me up some nosler lr 142 grain with 43 grain w760. Gun doesn't like them. Is the twist in the barrel that's the problem ? If so what bullet and load do you recommend. This is for hunting Whitetails. Thanks

@johngeddes7894 Год назад

Winchester powder isn’t always ideal. Most reloaders claim great accuracy with H4350, and not too hot. Also, you need to know how far off the lands to be. This cartridge is sensitive to that, but every rifle is unique. Your load may be too hot for ideal accuracy.

@paulvenn4447 6 лет назад

No primer pocket uniforming/cleaning etc?

@randytrudeau952 5 лет назад

Can you speak to full length sizing versus neck sizing on the 6.5 Creedmoor? I’m assuming you full length case sized because it is new brass and will then neck size once it’s fire formed in your Ruger Precision Rifle? In general, do you neck only size rounds for bolt guns and full length size for semi auto’s or mag fed calibers/guns?

@jacobdeem8187 6 лет назад

Made it look easy

@dhermz3317 3 года назад

I want to get the whole set up ~ where can I get that set up and how much for the setup ~ thanks for the video

@rkwjunior2298 Год назад

I know nothing about reloading . Is a Dillon 550 sufficient for reloading for load development? I inherited a Dillon 550.

@swisski7 3 года назад

Do you recommend cleaning the brass after trimming/deburring before loading charges? I'm just curios about residual brass chunks after that process. I'm new to reloading and really appreciate your videos.

@konotreal7126 3 года назад

Good video. Is license required for reloading ammo in California?

@bobdinovo6889 3 года назад

Can you use a 6mm Creedmoor rifle and swap out the barrel chambered in.243 win?

@casey197930 5 лет назад

Wanting to start reloading with my first 6.5 creedmoor, would've been great to have links to everything in this video.

@Ultimatereloader 5 лет назад

Random Dude It’s all here in the write up! ultimatereloader.com/2018/02/09/precision-6-5-creedmoor-step-by-step/

@mikecarlson6083 6 лет назад

Great video. Ht kind of velocity did you get? Do you use lighter loads than u shoot on your videos? I'm at @ 41.5 of h4350 and not over max. Thx again. Have you tried reloader 16 yet

@dailypokepulls 2 года назад

Do you have a link for the tools you used?

@zeissOholic 5 лет назад

What about primer pocket uniforming, flash hole deburring, bullet seating depth? Also, neck bushing or F/L bushing dies to prevent excessive working of the brass over a usually crooked expander resulting in excessive run-out and also measuring run-out? Not precision reloading at all just a standard reloading video.

@francescodox78 4 года назад

Great video Gavin...i know it is just me and dumbness, but how can i find the "next video" where you go through the load development process for the 6,5CM? Thanks

@francescodox78 4 года назад

whooops...i think i found it. :-)

@zachgruber8065 3 года назад

What press and stand are you using in this video

@just.some.dud3 6 лет назад

Hey Gavin, are you going any true precision loads for your 6.5 bolt rifle (assuming these are for an AR platform or you wouldn't be worried about SAAMI spec) using fire formed brass and only sizing the neck and bumping the shoulder if necessary? That's more what I load/shoot with my Forster and my 6.5 creedmoor rounds.

@silentbob267 6 лет назад

A lot of competition shooters full length size for their bolt action rifle shooting. Most articles I have read where the authors have tested full length sizing vs neck sizing side by side saw no benefits in accuracy or brass life with neck sizing only and tended to prefer full length sizing because it mitigated feeding issues.

@jakemann4969 2 года назад

How much does this reloading set up cost??

@evanwindom3265 3 года назад

You're assuming your audience has the context for all the dies, etc. They don't necessarily. How, for example, do you set up the die correctly? Why doesn't anyone include that in their videos? if people (like me) are new and don't have a full understanding of those bits, how will they diagnose if something isn't right?

@bwr3rd 3 года назад

Shouldn't you trim the case before you prime it?

@MikeHammonds804 3 года назад

In this video is the Brass New or Once fired?

@edroberts5126 3 года назад

What kind of reloading press do you use? Thanks

@dasroteeichhornchen411 6 лет назад

Good Video, but please try to change your hands. Your left back of hand covers the sight to the things you are doing. Maybe a little less fast all steps. I am a beginner as well. Greatings from Vienna, Austria, Europe. Thank you

@jaredcrowley5666 3 года назад

Do you anneal after each firing?

@deerphoria4314 4 года назад

Do you have any load for copper bullets using a 1:8 twist? Primer, powder, bullet weight

@johngeddes7894 Год назад

Hornady does for the GMX, and CX, which use all the same data. Barnes does for the TSX, TTSX, and LRX. All free pdf charts for downloading. So does the Hammer forum. Tons of calibers listed in 2 free pdf.

@Mr.Cheeseburger24 4 года назад

Hey Gavin, thanks for the video. I wanted to ask if it is neccesary to neck size my brass. I am too, trying to reload 6.5 Creedmoor. I have been getting mixed opinions on that over the net.

@peterhert9350 Год назад

Some people full-size every time. Some , like me neck size mostly and full-size if it's necessary ( loading gets difficult). For a hunting round and AR it's better to full-size always.

@quiquecruz6203 6 лет назад

Wath bullet user in Hornady.. of 147 grains ELD....?

@jawsmod 5 лет назад

140G ELDM

@Kingfish087 4 года назад

Is there any difference in using a small primer vs a large primer for 6.5 Creedmoor?

@Ultimatereloader 4 года назад

Yes, some differences, discussed in detail here :www.starlinebrass.com/articles/download-65-guide/

@lonz73 6 лет назад

Good video but you missed a lot of steps involved in the reloading process that a beginner needs to know. It’s not as simple as placing the bullet and pressing it into the case without speaking about COAL or showing the step where you removed the case lube from the case and case neck.

@Ultimatereloader 6 лет назад

lonz73 Appreciate the feedback but I think you missed the point, this video is about showing the process ay a high level end to end- all of the minute details are covered and many of the other videos I’ve published. :)

@joejr9653 6 лет назад

Great how to step, since I have not started to reload yet. What does all the equipment you used cost? Plus I presume you would need a tumbler to clean the brass? So that would be another cost too. Thank you.

@Intrusive32 6 лет назад

Joe Jr an RCBS kit is really cheap. It has everything you need basically besides a case trimmer dies shell holder and a tumbler. Hornadys reloading kit is overpriced tbh. You get a bunch of plastic and a crappy scale you’ll change after the first use. Go with rcbs with the balance beam scale. You’ll probably make an initial investment depending on what you get. The lee kit seems amazing and it’s like $130. With dies a cheap tumbler shell holders and trimmer you’ll probably be looking at $300-400. Depending on what to yuse

@Intrusive32 6 лет назад

I have a Dillon XL650 which is the progressive standard and I paid about $500-600 I forgot the exact price. Im 15 but i don’t like cheap stuff. Especially when your life depends on it . Don’t cheap out on the scale man. Can’t go wrong with a balance beam. Personally recommended Dillon as well. I had an issue with mine sent it in and got a new one

@Intrusive32 6 лет назад

If you’re interested in exactly what I use I’ll tell you just reply. And I’ll tell you exactly what I own what i like or dislike

@silentbob267 6 лет назад

All of the equipment in this video would probably put you up around $1000 give or take a bit and would be an awesome setup for precision rifle reloading. If money is tight you can get started reloading great quality ammo for considerably less than that. For a beginner on a tight budget the Lee Breech lock challenger kits are good. For a little more money and a lot more capability I would recommend the Lee precision classic turret press kits, they are a lot of press for the money and I wish I had known about them when I started reloading.

@joejr9653 6 лет назад

Craig Arnold I've been looking at all different press options. I haven't locked down on one just yet. The lee classic turret press does look good.

@TonyBlah 5 лет назад

How much would this set up cost? I've never reloaded anything, but just purchased a ruger precision rifle in 6.5 creedmoor and plan on it.

@Ultimatereloader 5 лет назад

Figure approx. $800 - here's a complete list of what you'll need! ultimatereloader.com/getting-started-reloading/what-you-need-to-load-rifle-ammunition/

@TonyBlah 5 лет назад

@@Ultimatereloader thank you sir!

@rubear71 4 года назад

Oh brother is the 6.5 PRC dead please do a reloading video before I switch my barrel to 6.5 creedmoor

@amirbadshah755 2 года назад

👍👍

@Chris-tw4jm 6 лет назад

What are the chances of you digging into the world of 270 Winchester?

@Belbivdevoe 6 лет назад

What reloader is this?

@Tito4246 5 лет назад

should've showed bumping the neck, most important thing that i missed when i first started reloading

@marinerabbit9441 5 лет назад

You don't bump the neck. You either FL size and bump the shoulder a tiny amount, or you neck size for whatever neck tension your bushing is for, then have the option to run it through a body die if you want to bump the shoulder back after neck sizing.

@PilotMcbride 6 лет назад

Woulda been better if you did 22-250........ lmao!!! Always great to see quality equipment used correctly. thanks and Cheers from downunder :)

@robleo69 6 лет назад

Gavin, Almost complete but you might just want to run it on Sinclair ball concentrically gauge to show the accuracy of the dies and the press. (All I've used for a long time is the Coaxial or, L.E.W. inline dies/press.) For those new to loading and or the anal retentive freaks. Like me..Lol

@peterhert9350 Год назад

Don't trust any COAL in Books or loading data. Measure always with an unloaded Cartridge in your specific rifle. I load about 15 caliber.

@dawiejacobs5101 Год назад

No sound

@chrisv.8667 6 лет назад

do you think you'll ever reload 300 win mag

@Ultimatereloader 6 лет назад

Chris V. I hope to, in the near term for belted magnum I think 7 mm will be first…

@chrisv.8667 6 лет назад

gavintoobe that would be awesome. I don't have a current reloading book with data for 178gr eldx Hornady bullet for the 300 win mag. I was wondering if you have a book that has it and if so could you send me a screen shot of that page. If you could that would be awesome. I look forward to you reloading some belted magnum cartridges. Keep up the video's your doing a great job. Thanks bud!

@nicsu2128 Месяц назад

I don’t believe you for a second. Maybe this is how you load you meh ammo, but what about your match grade stuff. No mandrels? You wet tumble after sizing?

@r.braathen 6 лет назад

Hmmmm precision...............

@hank3152 6 лет назад

I hope you cleaned the case lube from your fingers before you handled the primers.....

@Ultimatereloader 6 лет назад

That goes without saying :) :) I keep a blue shop towel on the bench for that kind of thing.

@hank3152 6 лет назад

gavintoobe I figured you did off camera

@pjlonely2891 Год назад

😂😂😂 how much for the tool And all stuff 😢

@zanpekosak2383 6 лет назад

Please reload .224 valkryie or .50BMG or .338 lapua magnum. Of couse if you ever get the support from companies like rcbs since .50 presses are expencive.

@ZERO_42069 6 лет назад

AirsoftSlo this guy once said he had like 20 presses (in an older video) im sure he can afford a 50 bmg press if he dont have one already

@zanpekosak2383 6 лет назад

Josue Guzman All I wanted to say was that I dont WANT a vifeo on this but I WISH there would be one. I am not forcing him to do it but i would be happy to see that video.

@Ultimatereloader 6 лет назад

Yes to all (I hope) - working on it!

@ZERO_42069 6 лет назад

AirsoftSlo gotcha, i reload 50 bmg but id love to watch him reload it, his videos are great

@zanpekosak2383 6 лет назад

Josue Guzman Man you americans are lucky to have .50. Max in europe without a specialty high caliber permit is 338. And even for that you need a bunch of paperwork

@caindobro4565 5 лет назад

No cleaning of the primer pocket? No deburring of the flash hole? Not sure as I would call this "precision" reloading.

@johnnycostner6806 6 лет назад

This is Basic reloading Not precision reloading....

@Ultimatereloader 6 лет назад

Curious definition of basic reloading...

@johnnycostner6806 6 лет назад

Why's that ? You mentioned nothing about headspace, neck tension, primer pocket uniformity, case and bullet sorting etc. Nothing wrong with the video...I'm just saying the word precision was misleading in your title...I would think you would have to agree that this was a demonstration of basic reloading.What about this video goes beyond basic cartridge making ??

@silentbob267 6 лет назад

You can't really expect a video under 5 minutes long with a title indicating it is a "Quick Look" at reloading to hit every single aspect of precision reloading in fine detail.

@Ultimatereloader 6 лет назад

Craig Arnold Thanks Craig- that’s exactly what I was going to say :) As I mentioned in the video I have other videos that cover all of those details.

@franciscoortiz9730 3 месяца назад

Do you need to crimp 6.5?

@Ultimatereloader 3 месяца назад

@franciscoortiz9730 3 месяца назад

I went by the Lyman book exactly, and my rounds won't chamber

@Ultimatereloader 3 месяца назад

Are you using a SAAMI-spec case gauge?

@aaronu6870 2 года назад

Did you know your setup is in the Starline Cartridge Guide for 6.5 Creedmoor? You're on page 9. www.starlinebrass.com/media/2138/complete-65-creedmoor-guide-reloading-65-creedmoor-ballistics.pdf