Recreate an STL file in Fusion 360

Подписаться 964

Просмотров 3,2 тыс.

50% 1

Someone wanted to make changes to this STL, and was wondering if I could do it. Sometimes you can convert STLs in Fusion360 easily and edit them. However, that doesn't always work, as in the case of this file. In this video I'm giving you a glimpse on how I approach this task. This is a one-take, unscripted video, so sorry for how unorganized and scatter brained it is. Hopefully you can pick up some helpful tips though!

Хобби

Опубликовано:

1 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 22

@iangriggs 9 дней назад

Perfect timing for this. You covered a few areas I been wondered how you do in Fusion. Thanks!

@Grazfather 5 дней назад

When you try to measure the thickness, you can use the measure tool, and in the Results section you can click on the XYZ delta part and it'll give you the distance along your X,Y, and Z, For the thickness of the base that's just the Z, and for the thickness of the walls you can do sqrt(x^2+y^2) .

@ShopTherapy623 5 дней назад

Can you do that to the mesh, even though you can’t select any surfaces or edges?

@Grazfather 3 дня назад

@@ShopTherapy623 you can select the edges on the mesh with the measure tool, and as long as the surfaces match your coordinate plane then the x y z values will line up.

@pixieloco 12 дней назад

thanks for this.

@ShopTherapy623 12 дней назад

Thanks for being kind. Lol. The audio is pretty bad and I’m a bit scatter brained. However this wasn’t rehearsed, and I did it in one take!

@WhyplayGaming 11 дней назад

I think it was fine for an unplanned video. I think some people may find it helpful to see the thought process behind what you are doing rather than just showing people the correct tool every time. Its also good for people to realise you might not always get it right the first time. I enjoyed it either way. I would not have thought to use the surface tool.

@tbkowens 9 дней назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-lhL48dcOodM.html need to do the inside fillet first and then the external fillet in order to achieve the correct 50mm filet you were after.

@ShopTherapy623 9 дней назад

Yes! I figured that out after the video! That’s one of the problems with doing an unplanned video!

@tbkowens 9 дней назад

@@ShopTherapy623 Thanks for sharing regardless. I like watching fusion projects and thinking about how I would do things differently. Fun little brain challenge.

@WhyplayGaming 11 дней назад

Just a thought, if you extrude to a new component, then when your testing one will be transparent so you may get a more accurate look, you could also try changing the appearance off-cause.

@ShopTherapy623 11 дней назад

Im not sure I'm following this comment. Do you mean when I was trying to extrude the hood down to the base/bowl?

@WhyplayGaming 11 дней назад

Regarding the beval at the end, You needed to do the inside to 50 first then do the outside to 50.

@ShopTherapy623 11 дней назад

Yes!! I realized that after the fact! Thanks for pointing that out! There are a few things I'd do differently now that the video is over! lol

@Grazfather 9 дней назад

I see that gridfinity plugin button!

@ShopTherapy623 9 дней назад

Heck yeah!

@TheTangoAlfa1 9 дней назад

What do you mean by Prismatic is not going to work? Did it error out?

@ShopTherapy623 9 дней назад

Yes it errored.

@neonblowfish 13 дней назад

Please increase the audio, you're too hard to hear. Thx!

@ShopTherapy623 13 дней назад

Thanks for the feedback! I just recorded this with my laptop microphone. If I continue to do more "how-to" videos, I will think about getting some better audio!

@pixieloco 12 дней назад

at 36% volume (using headphones) I can hear it without any issues.