Remove Steering Linkage, Steering Gearbox, Steering Wheel, Engine Frame Mounts - 1966 Mustang

Подписаться 11 тыс.

50% 1

Today at Alf's Mustang Garage we continue with our 66 Mustang fastback 6 cylinder to 289 conversion. We continue by removing the steering linkage, steering gearbox, steering wheel, steering column, accelerator bell crank, engine frame mounts, and front sway bar out of the car.
Things I used in this video.
As an Amazon Associate I earn from qualifying purchases
Steering Wheel Puller amzn.to/3UABAQl
Lighting setup amzn.to/3PwJnf1
GoPro Camera & accessories amzn.to/2NwysVu
Basic mechanics tool set amzn.to/3ob7q2B
Subscribe to the channel and click on the notification bell. / @alfsmustanggarage
We want your thoughts and comments below. What kind of project are you working on? What Mustang are you daily driving?
Alf's Mustang Garage is not responsible for any mechanical or technical error that you may encounter when working on your own car. You are responsible for your own quality control and your own proper repairs.
0:00 Intro
1:14 Steering Linkage
5:38 Engine Frame Mount
6:38 Front Sway Bar
8:55 Steering Wheel
11:44 Steering Column
14:13 Steering Gear Box
15:20 Gas Pedal / Bell Crank

Авто/Мото

Опубликовано:

21 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@janinedelcamp1941 2 месяца назад

I'm always learning something good from your videos. Thx loads!

@AlfsMustangGarage 2 месяца назад

You're very welcome. You know what's cool? I learn something new from doing all this stuff too. 😃

@user-yn5kb7ep2l Месяц назад

Great work alf. Looks like the need some new floor boards as well!

@AlfsMustangGarage Месяц назад

Yes! She did need a front driver side patch. Luckily, it wasn't too bad. Passenger side had a past repair.

@JefeBailey 22 дня назад

Hey Alf! Thanks for all the great videos! I’ve got a ‘67 convertible and I’m in the process of installing new suspension and disk brake conversion (CSRP). I’ve gotten everything removed and want to clean up the underside and wheel wells. What type of undercoating did you use? How important is it to grind all areas of surface rust back to bare metal? Thanks!

@AlfsMustangGarage 22 дня назад

We used Raptor undercoating on this. You'll want to keep in mind if you sand that floor to bare metal, you need to coat it in a direct to metal epoxy primer first. The undercoating doesn't provide a sealing agent and is not intended for direct to metal. You don't necessarily have to take it to bare metal either. Just depends on the car if you still have the original primer down. We just did a very through job of cleaning and degreasing the floor and then went over the original primer with a light scuff before spraying the undercoating. I hope that helps.

@JefeBailey 22 дня назад

Very helpful. Thank you! Really appreciate the reply!

@JefeBailey 13 дней назад

OH...forgot to ask: What reference material do you use to get torque specs on 1967 mustang?

@JefeBailey 12 дней назад

OH...forgot to ask: What reference material do you use to get torque specs on 1967 mustang?

@AlfsMustangGarage 12 дней назад

I just have an old service book but you can get that stuff from a Chilton manual as well.

@JefeBailey 12 дней назад

@@AlfsMustangGarage Thanks Alf! Appreciate all of your help and advice!

@gregwarren7840 10 дней назад

I have a rebuilt steer gear box off of a donor car. Do I have to yank out the column if I'm just replacing or can I just slide the old one out and put the new one back in? Thanks!

@AlfsMustangGarage 9 дней назад

I have found that you have to remove column because you need to room to pull it out. Plus, if it's a V8 car and the engine is installed, you won't be able to get it out without pulling the engine.

@BPattB 2 месяца назад

Hey bud i wss wondering if you could tell me a donor car i could use to order a master cylinder from. I did the front disk brake swap. So now the car is disk/drum manual brakes. Could I use a 69 Mustang disk/drum manual? I tried the 75 Mavrick master but i think i may have ended up with the power master. The brakes are really soft and brake lights dont turn on until the pedal travels a long way.

@AlfsMustangGarage 2 месяца назад

What year is your car?

@BPattB 2 месяца назад

@@AlfsMustangGarage 1965

@AlfsMustangGarage 2 месяца назад

@BPattB I usually get a 67 Mustang master cylinder when I'm in this situation.

@BPattB 2 месяца назад

@@AlfsMustangGarage right on man thank you

@AlfsMustangGarage 2 месяца назад

@BPattB you're very welcome!