Replace Conical Grinder Burrs in Jura Coffee Machines

Подписаться 5 тыс.

Просмотров 48 тыс.

50% 1

Click this link to purchase Jura Grinder Burrs: shop.partsguru.com/Jura-Grinde...
Click this link to Purchase Jura Oval Head Key: shop.partsguru.com/Jura-Oval-H...
Click here to purchase Jura Parts: shop.partsguru.com/Jura-Capres...
We sell and repair all Jura Cofee Machines.
In this video, the Guru demonstrates how to replace conical grinder burrs in Jura grinder assembly that is used in all Jura home and professional coffee machines.
The conical grinder burrs should be replaced every 2,500 cups of coffee. FILL BEANS error message in Jura coffee machines indicates that grinder burrs should be replaced.
Maintenance Tip:
Avoid using dark roasted and oily coffee beans in Jura automatic espresso machines. The oil residue from dark roasted coffee beans clogs the inner grinding chamber and blocks the coffee outlet to the brew group.
Click the link below to purchase the Jura conical grinder burrs:
www.shop.partsguru.com/Jura-Gr...
We carry Jura parts and repair all Jura home and commercial espresso machines.
Email: sales@partsguru.com
Online Jura Parts Store: www.shop.partsguru.com/Jura-Ca...
How to Fix Grinder in Jura Espresso Machines
Fix Grinder in Jura Espresso Machines
How to replace grinder burrs in Jura espresso machines
replace grinder burrs in Jura espresso machines

Хобби

Опубликовано:

12 ноя 2014

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 83

@acer4me 6 лет назад

I don't think that people who have seen this wonderful video are quite appreciative enough, since without it, the only alternative would be to cart these hefty machines to Jura for a very expensive repair. Therefore I offer my gratitude for the trouble taken to prepare this video.

@zazaian 7 лет назад

Thanks for taking the time to record this. I'd taken my grinder apart to clean the burrs, then found that I was having trouble re-seating the lower burr on the bearings. Watching this gave me enough information to figure out that I was probably on the right track, and was actually applying enough torque when re-attaching the central screw. Seriously, thank you, thank you, thank you. You saved my evening, and probably at least a couple of coffeeless days.

@PartsGuruUSA 7 лет назад

Hello Mike, I am glad to hear you found the video helpful. Thank you!

@gaborgyuris5128 7 лет назад

Yesterday my Jura coffee machine stoped working I wanted to call someone who can fix it when I found this video. and I was able to do it myself so I would like to thank you this was a big help for me. I will invite you for a good coffee lol.

@rayates4446 6 лет назад

Hello from the south-west of France. I just wanted to take this opportunity to thank you for your excellent explanations on how to replace the grinder and also take out clean and put back the brew group assembly for us in our Jura Impresa 9. We have owned this machine for eight years with zero problems at home and would not of been able to repair it without your help. Many many thanks :-) Furthermore I really appreciate you explaining how the items and units actually work it makes take it apart and putting it back together much easier.

@PartsGuruUSA 6 лет назад

You’re welcome. Glad you were able to fix your machine.

@RuudKuin 6 лет назад

Even after nearly four years this still is very interesting... I'm very much into repairing and servicing Jura coffeeshop machines for friends and myself. Great bidets, thanks a lot!!!

@maxagent86 7 лет назад

I will add my voice of gratitude to you for a great video. It worked beautifully for me and saved me time, money, and some grief...Just a small addendum that may help a few folks: after you tighten the screw to fasten the conical burr (around 20' on the video), look at the base of the burr through the coffee outlet (as shown around 18'55" on the video) - there should be no space whatsoever between the base of the burr and the plastic, i.e. the balls should no longer be visible (they can be visible before you tighten the screw). The first time I did this, there was still some space there after I tighten the screw and I still got the "Fill Beans" error. After re-sitting the conical burr and eliminating that space, everything worked great.

@PartsGuruUSA 7 лет назад

+Maxwell Smart thank you Maxwell. I'm glad it worked out for you.

@BillPowell1203 7 лет назад

This was very helpful. However, even after seating all the way down I found that my grind was still far to fine, like flour. I adjusted the wheel to a more counter clockwise location than my original markings and that solved the problem. Perhaps the original burrs were a slightly different size or worn down?

@PartsGuruUSA 7 лет назад

+Bill Powell Hi Bill, please change the grind setting one notch at a time towards coarser position. Make individual cup is espresso three times. Make the 4th espresso. Check the fineness of the used coffee puck between your fingers. Please adjust it until you get the desired output which is coarse like table salt grain.

@stevegerow872 5 лет назад

Terrific, helpful video! I have a Jura 560 (Capresso Infinity) and managed to get the coarseness out of adjustment. The part where you show how the adjustment key is indexed to the upper burr is what I needed. Mine had no marks but when I got it properly set I marked it between the burr and rotating key. Thank you again for this valuable video!

@nunnsie23 8 лет назад

Perfect instructions, big thanks! I saved $100s in labor :)

@mahiyarmirza1538 9 лет назад

Wonderful demo and extremely informative many thanks

@richardsutton8193 6 лет назад

Very good video, as always. Well done Parts Guru. Where would we be without you? One thing people might find helpful, though: in the end the only way I could get the tabs on the worm gear to engage when screwing down the assembly was to mark their position with a felt tip pen on the outside of both. Then when I screwed it down and looked through the ground coffee outlet, I could see that there was no gap and the balls couldn't be seen.

@JosephKimJoeyBigTime 8 лет назад

this guy is a genius. love this series.

@PartsGuruUSA 8 лет назад

Thank you Joey. We're glad to help!

@drewbieroks6119 7 лет назад

Happy New Year everyone!!! I have a Jura Ena 3. I have successfully removed and disassembled/re-assembled the brew group; however, I can't figure out how to remove the grinder unit????? Is there a video available that shows that?

@annashelbaer3676 7 лет назад

I just watched this video and it is so good, thank you! The only part that is missing is how to get to the grinder to begin with. I have the Jura C60 and in my half asleep daze, I just poured a small amount of water into the beans when it asked me to fill the tank. I am afraid to use it now because I am afraid I will damage the machine. How do I open it up to dry it out. Also, I do use dark roast beans even though I know I am not supposed to. Is there a way to get that nice strong brew without using dark roast beans? Thank you!

@Fred-nt8jq 6 лет назад

Thank you for your share, i can repar my ena5 with you help

@NYCgoblue 6 лет назад

Hi and thanks for the video. I had difficulty in taking the top burr out. When I turned the outer ring all the way, the burr still did not come off. I snapped the ring off (and lost the tiny ball bearing in the process). I loosened the inner bolt and lower burr, but never took it off. I cannot see the ball bearings below it, mainly because I did not remove the grinder from the machine, but also because it seems something kind of ring sits beneath the burr. When I put the pieces back together, I tried to align the burrs as they were when I opened the machine. I placed the black ring on top where the "absolute zero" aligned with what looked like a mark for zero on the ring with holes. The ring doesn't seem to have a stop any longer when I adjust the grind. And the espresso comes out tasting like coffee. The grind is way too coarse. I was getting the fill beans message for a while (though not much the last few days) but the coffee was good. (I believe the pucks were much larger, though I confirmed the powder and water settings were not changed.) Can you please provide some advice?

@mbose 5 лет назад

very good thanks. Would you please show a video on 'How to remove the grinder unit" PLEASE.

@RobBrownTV 9 лет назад

Thank you!

@tongco7987 7 лет назад

Hi I have a Gaggenau CM200610/03. I keep getting 'add beans' even after cleaning the grinder, etc. Do I require a new grinder unit entirely? By the way your video is most helpful to take apart the unit. Thanks

@AryeHvsv 5 лет назад

Thank you for this and all the other videos. I've been able to refurbish many parts of a hand-me-down Jura S9 OT with your help. I replaced the conical grinder burrs as per the video. My question is about putting everything back together. I put the dial adjuster in to be around halfway (medium-size grind) when the grinder is at the home position, closed the machine and refilled the beans. Now I can't make adjustments towards the finer position, but it will easily turn to the coarser position. I tried while the machine was grinding beans several times but I can't make adjustments to the finer adjustment. Before putting the dial back in, i was able to twist the grinder easily. Only after closing it up I realized it won't change positions as easily. Can you explain how to put this back into the machine, what grind size the home position indicates, and if I made mistakes along the way?

@perspook2418 8 лет назад

Hi, Thanks for a great video. I have the Fill beans error on my Ena micro 9. After claning the grinder without luck I have changed to a new grinder, but I still get the Fill beans error. Any suggestion? Thank you in advance.

@guy6052 6 лет назад

Could you refer to a video on removing and reinstall the grinder (Impressa S8) from the unit? Thank you

@fedeshimo 9 лет назад

Hi, i got a saeco vienna plus like five month ago it was working fine but one morning i start the machine like usual, and after grinding it make a strange noise and the machine stopped the process i tried again and it wouldn't grind at all, i open the coffee dump deposit where grinned coffee ends after a cup and found some metal balls and some plastic, i dissemble the machine i think i found where the plastic parts belong but i have no clue where the metal balls are from y clean the machine and ensemble it again it when i tried the machine worked, but i could make like 6 or 7 cups of coffee but then the machine stopped again, thank in advance for your reply

@briankiefer 7 лет назад

I partially disassembled my 560 to clean the burrs and after reassembly, the adjustment settings do not work. It is always extremely fine even when set on coarse. Otherwise it operates as normal. Any advice to diagnose or fix why the adjustable grind is only producing very fine grounds?

@jaimeemonaghan6443 8 лет назад

How do you remove the grinder from a Jura Z5? I am receiving the Fill Beans error with beans already in, will order the burrs but couldn't find any videos specifically to remove the grinder. Great tutorials btw!

@PartsGuruUSA 8 лет назад

We have a video that demonstrates removing the side panels and brew group. That's the most difficult part. Removing the grinder should be easy once the side panels and front cover is removed. Let me know if you still need help.

@peterv9176 8 лет назад

Hi Guru, great video. I just don't seem to find the instruction of how to remove the grinder unit from my machine (Ena-5). Is there no video available for that or am I just not looking in the right place? The side and top cover are removed, the three srews also, but then....?

@willo7979 5 лет назад

Thank you for the detailed servicing process for grinder unit. While a metal burr grinder lasts around 2500 grinds, what about a ceramic one? Does it last longer or shorter? By how much? Thank you.

@PartsGuruUSA 5 лет назад

Conical burrs are the best as they ensure that coffee is grounded to the actual adjusted size, finer or coarser, it’s always uniform and consistent. The ceramic burrs last longer but the ground particles are not always uniform. Are you considering a new espresso machine?

@sergethibault251 7 лет назад

I change the grinder unit on a XJ9 and adjusted the grind. Everything seems to be correct except I'm not getting enough grind (only +- 30%) to form a good puck and brew good coffee. Any ideas? Is there are secret maintenance menu to adjust the grinder time?

@bjww 6 лет назад

Have you solved this problem?

@chc0318 8 лет назад

I have broken my Gaggenau CM200610 grinder due to I adjust the degree of grinding while the grinding unit is at stop status. Gaggenau using Conical Grinder Burrs. Could anyone explains to me why I can only adjust the degree of grinding while the grinding unit is running? Also, how does it work to adjust the degree of grinding? Thanks.

@davidbarbour2368 7 лет назад

The narrator has the lower (inner) burr inserted into the upper (outer) burr backwards during his explanation (04:00 to 06:00). Also, it is not necessary to remove the motor mechanism from the housing in order to clean and/or swap the burrs out.

@seandineen1134 6 лет назад

Thank you for clarifying that!

@ralph17p 7 лет назад

I've just removed the grinder from an ENA 9 that I bought off Ebay which had a fill beans error. I followed the disassembly instructions in this video, and was careful to collect all the small pieces that came out. However, while I have the 3 springs and ball bearings as shown... I also have another smaller ball bearing and thinner spring that I'm unsure where they should go back. Any idea where these might have fallen out?

@seandineen1134 6 лет назад

Did you figure out where that spring/ball bearing goes? It sits in the plastic cylinder at the top of the grinder and the ball pops in and out of the holes at the rim of the dial. Makes the tick, tick, tick sound as you turn the dial. REALLY hard to get back in, in my opinion. Maybe try masking taping it in the cylinder, putting dial back, and try somehow remove the tape after?

@gregbarmine3678 7 лет назад

I replaced the grinders in my Jura Impressa F9 (purchased from Parts Guru). I think the coffee is grind too fine because too much water comes out in the tray as oppose to the cup. Where does the top assembly tabs line up with the beginning of the plastic threads on the lower assembly (for the course setting)?

@PartsGuruUSA 7 лет назад

+Greg Barmine Hi Greg: please call us to speak to Jura technician so we can assist you with your issue

@andrew1321 8 лет назад

I removed the bottom burr of my grinder to clean it out. Upon trying to reassemble it though, I can't seem to compress the springs enough to place the bottom burr to the correct position. I know it is incorrect because the plastic worm drive bushing is not able to fit within the burr. I tried to assemble it anyways and the grinds I get are incredibly fine, which makes sense as the bottom burrs are now closer to the top burrs. Any advice on how to fix this? Seems odd that the springs are so stiff/long...

@PartsGuruUSA 8 лет назад

Please try again. Replacing the burrs is a precision work. In most cases, it takes more than one try to get it right.

@aussielucas 5 лет назад

My Jura Ena 9 Micro, has started playing up. The grinder motor can be heard trying to move the burrs but it wont spin at all. Pulled it apart cleaned it and still doesn't spin. Is the motor burnt out even though it makes the noise?

@PartsGuruUSA 5 лет назад

Hi Luke, Either the grinder motor or the power board is malfunctioning. Please check both. On the other hand, you can ship the machine to us for repairs, if you like. We’re located near Philadelphia, PA.

@bjww 6 лет назад

How to adjust the grinder to grind more coffee? It grinds very little coffee - too little to form a proper puck of coffee? The coffee machine is based on Jura E-series and I got after many years in the attic. Burrs seem to be in proper shape... Any help? any ideas?

@PartsGuruUSA 6 лет назад

Hello, The coffee quantity is determined electronically depending on the coffee strength you select upon brewing. It ranges from mild to strong. Did you try to make coffee at strong setting? If still weak, then you should consider replacing the grinder conical burrs. Over time, the sharp teeth on the grinder burrs wear out and get blunted. And, don’t grind enough coffee so end up producing weak coffee. You should also check the used coffee puck after brewing the coffee. The ideal used coffee puck should be well formed and solid just like the hockey puck.

@timoseppala7137 6 лет назад

What size are the ball bearings that are in the grinder? (Lost them accidentally)

@PartsGuruUSA 6 лет назад

Hi Timo, not sure about the size. You can order from us if you like.

@Rockuhill 7 лет назад

FYI in case it helps anyone. I mistakenly replaced blue/red wires and grinder spun in OPPOSITE direction, without grinding anything (just a whirrrr). A quick swap back to correct placement fixed it and back in business!

@PartsGuruUSA 7 лет назад

Thank you for sharing. The switching of the wires result in spinning the motor in the opposite direction.

@rayates4446 5 лет назад

Hello I’m getting the full beans error on my machine j9 I have changed successfully the grinder blades on this over last summer thanks to your video I have just tried to change them again with new (even though the other was only 9 months old) but it has not helped. Wondering if the grinder motor could be at fault. Any suggestions would be very welcome. Thanks in advance

@PartsGuruUSA 5 лет назад

Hello, the grinder burrs should be replaced every 3,000 cups of coffee to ensure the best coffee extraction. Which grinder burrs did you install in the J9? Did you purchase the grinder burrs from Parts Guru?

@rayates4446 5 лет назад

Hello Parts Guru No being in France I had to source them elsewhere. But they worked fine for 6 months. Can’t get the new ones to work properly at all. It’s like the grinder is slipping over the beans instead of grinding them. :(

@PartsGuruUSA 5 лет назад

I am not sure if you purchased the correct burrs. It’s hard to help without knowing what you purchased.

@rayates4446 5 лет назад

Parts Guru thanks for your help - Broyeur V5 Kit de réparation pour Jura Impressa + Jura ENA www.amazon.fr/dp/B0741B5C4Z/ref=cm_sw_r_cp_api_i_aSBPCb2A1D7W7 This is the grinder part we purchased.

@roadstar554 9 лет назад

I wish I had watched this video sooner. I have broken the tabs which hold the top and bottoms of the grinder. Is there any way to fix this or do I need a new grinder? Your help is appreciated.

@PartsGuruUSA 9 лет назад

Hi, unfortunately the grinder is sold as a complete assembly. What model Jura machine do you have?

@roadstar554 9 лет назад

Parts Guru I have the jura j5. I have used electrical tape to hold it together. The grinder is not working at all however. Could it be the Grinder Burrs or the electrical tape that is stopping it from working? It made a noise the first time now there is no noise at all. Is there a simple way to test the motor while it is out?

@PartsGuruUSA 9 лет назад

roadstar554 I don't expect the grinder motor to be an issue as it rarely malfunctions. Can you email us a picture of what the grinder looks like now? It's best to replace the complete grinder assembly if the upper part is broken off the motor. The electrical tape won't hold it long and I don't think you can operate the machine.

@vitalijsalkauskas2949 8 лет назад

+Parts Guru Hi can you adjust the grinding time on jura coffee machines

@Former_Texan 8 лет назад

My grinder got wet (no one in the house will explain why there was water on top of the machine). After a full disassembly and cleaning the grinder has been grinding powder fine. It is so fine that it clogs the brew grew filter. I tried replacing the burrs (my product counter was about 4500) and it's still grinding power fine. You say to adjust it, but how? As you adjust towards coarse it's not long before you are at the disassembly position. Have I not tightened the center screw tight enough (leaving the springs insufficiently compressed)?

@PartsGuruUSA 8 лет назад

Hi Charlie, when you adjust the grinder to coarse setting, please make three coffee's for the adjustment to take place. It's important to adjust the grinder while its grinding.

@Former_Texan 8 лет назад

+Parts Guru I adjusted it at the very beginning when the grinder was clean and run it a half dozen times. I had to run it 3 times before the machine would even see enough ground coffee. The fine coffee is like baby powder and sticks to everything. My new burrs and old burrs both feel similar, I think I have had an assembly problem the whole time, but I can't figure out what it is. The white wire connects to the + terminal on the motor, right? The worm gear appears to be turning the correct way to draw the beans in, but a backwards electrical connection might explain a lot. I wish I had some way to run the grinder on it's own and test it without having to reassemble the machine. I don't have a 120 VDC power supply available.

@Former_Texan 8 лет назад

The Videos of people taking apart the Capresso 560 seem to contain a rather similar looking grinder. Anyone compare these side by side?

@Former_Texan 8 лет назад

+Parts Guru I don't know what i did differently, but I took it apart a 4th time and it went together much better this time and works perfectly.

@PartsGuruUSA 8 лет назад

Replacing the grinder burrs is not an easy feat. I'm glad you were able to get it right. Enjoy the delicious coffee!

@omerkaya5936 8 лет назад

Thanks for explanatory video. Do you have any information to share how to remove grinder unit from machine step by step basis? May be in pdf.

@PartsGuruUSA 8 лет назад

+Ömer Kaya Hi, yes, we need to know the model number of your machine.

@omerkaya5936 8 лет назад

+Parts Guru Jura Ena 5 white thanks.

@PartsGuruUSA 8 лет назад

Please email to sales@partsguru.com for grinder removal instructions.

@omerkaya5936 8 лет назад

Sent a mail already.

@alejandrorubendiazpalacios1877 5 лет назад

gracias por el video, tengo una maquina jura Giga X9 acabo de cambiar el molino pero me sale un mensaje VACIO CAFE podrian ayudarme, que debo revisar?

@oscarrodas2651 5 лет назад

Alejandro aqui está el manual de tu máquina, www.mycoffeeshop.com.au/WebRoot/ecshared01/Shops/mycoffeeshop/MediaGallery/Manuals_and_cleaning_instructions/Prof_instruction_folders/Giga_X9_inst_folder.pdf muchas veces tienes que limpiar los contactos del container.

@betsyharrington8687 7 лет назад

how do you remove grinder from ena5 to replace burrs

@PartsGuruUSA 7 лет назад

+Betsy Harrington Hi Betsy: we have the PDF instructions that shows how to remove grinder assembly from ENA models. It's listed on our website along with other useful DIY repair information and parts diagrams for Jura ENA models. Here's the link to our web page: www.shopjuraparts.com/pages/jura-ena-3-ena-4-ena-5-ena-9-parts-diagrams-and-diy-repair-guides

@betsyharrington8687 7 лет назад

Thank you very much!

@drumiktube 7 лет назад

PartsGuru, How do I remove top panel on ENA Micro 1 so I can clean the grinder. Thanks for you videos side panels already removed

@mguerramd 7 лет назад

The balls do not go on top of the springs. If you put the balls on top of the springs then you will never get the tabs on the worm gear to engage in their slots. If you put the balls on top of the springs the conical burr will set so high that the tabs on the worm gear cannot reach down far enough to engage. Drop the balls in the holes first and then drop the springs on top of the balls. It is the springs that fit into the three holes on the bottom of the conical burr not the balls. I spent half an hour fighting with the worm gear trying to get it to seat properly before I figured this out! The Jura factory parts diagram shows the balls underneath the springs not on top as well.

@richardsutton8193 6 лет назад

I've tried both ways and cannot get the the tabs from the worm gear to engage in their slots. I've looked online but the only parts diagrams I can find don't go into the detail necessary to see which way they go. Having said that, the circular indentations in the grinding burr are not large enough to take the springs, but they are large enough for the balls which suggests that the video is correct. How important is it that these tabs engage in the slots, I wonder?

@mguerramd 5 лет назад

The worm gear is what locks the motor driveshaft to the conical burr. The tabs fit in the slots for a reason, to lock these parts together. If you do not engage the tabs in the slots, the only thing holding the conical burr to the driveshaft is friction. To get enough friction you could easily tighten the screw so much you strip it. This assembly fits together exactly as I described it, the balls go on the bottom. If you watch the video carefully you will see he never gets the tabs firmly engaged down in the slots.@@richardsutton8193