Replacing the Oil Pressure Switch on a Peugeot 307

Подписаться 122 тыс.

Просмотров 91 тыс.

50% 1

How to replace the oil pressure switch on a 2001 to 2008 Peugeot 307. If you have an oil warning light on your dash but when you check the oil in your engine it's at the correct level, one possibility is that the oil pressure switch is faulty. The replacement part I used was a Metzger 0910102 and only cost €4.15. The torque setting for the switch on this particular car is 30 newton meters (22 foot pounds) Thanks for watching. Please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2021
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

Опубликовано:

4 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 64

@chrishartley1210 3 года назад

What you should point out is that the clip on the electrical connector is usually positioned in a place where you can't even get a fingernail to it.

@annamanna2295 3 года назад

It is a negative logic sensor, so "guilty by default until proven innocent" (here: pressure too low by default, until proven sufficient). In the first state (too low pressure), the electric circuit is closed (the control lamp on the dashboard lights up). In the second condition (sufficient pressure), the electric circuit is interrupted inside sensor (the control lamp is off). So you check the sensor itself like this: you unscrew it from the filter base and check with a multimeter by touching one probe to the sensor metal housing and the other to the pin from the plug. A closed circuit should appear. If not, the sensor is burnt and discard it. If it is ok, then take a hydraulic tee, mount this sensor in it and a dial gauge which will show the numerical values of the pressure. You will see when the sensor disconnects the circuit - is the correct pressure. You assemble tee into motor, into the sensor socket and start the engine. You check whether and at what pressure the sensor disconnects the circuit. Now you have all the data whether this sensor is still working well or whether you can throw it in the trash.

@zeez4178 11 месяцев назад

Very valuable information thanks alot.

@kalani1987 3 года назад

Wow. Wish the GM cars put that switch up front. Mine is located way back in the engine bay. Very little space to get to it

@paulfreer1302 6 месяцев назад

Hi No the light / warning / engine management etc are all Off. Just jumps for a second like a petrol misfire or water in the system. Mostly until the engine reaches working temperature. I'm an old guy worked on all my cars but this 307 hdi is driving me NUTS. Can't afford to change it and don't want to sell a Lemon to anyone. Worst car I've ever had. My 406 and 306 , citreon BX, Ford focus's all bloody great. Cured any problem myself no worries. But this has been 1 problem after another, spent 3 grand on it in 2 years in parts.🙄😔 thanks for your time 😂👍

@screwsnutsandbolts 6 месяцев назад

My previous 307 had a periodic drop in revs and I never found the solution. Is yours like this: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-eEW1W2yOXEQ.html

@markpitt5433 Год назад

Hello, great video. What if the wiring plug is the damaged part, do you know how/where to get a new one of those? (206 1.4 2006). Thanks

@screwsnutsandbolts Год назад

You can buy one here: www.aliexpress.com/item/1005003304272271.html You could probably find one on Amazon or Ebay too

@anthonyrusses6285 2 года назад

Where does the wire oil pressure sensor go? Because the wire 1 pin was cut off after servicing the engine .

@paulfreer1302 6 месяцев назад

Oh fuel filter etc done still does the jump

@paulfreer1302 6 месяцев назад

Thank you brilliantly instructive. BUT I was hoping it would cure a problem like a miss fire on a petrol . Like a jump Similar to an air bubble going through the fuel. Just a quick jump. Mostly as the engine is warming up. ANY IDEAS?

@screwsnutsandbolts 6 месяцев назад

You're welcome. It's hard to say, it could be caused by many different issues like fuel pump, clogged fuel filter, fuel injector etc. Is the engine light coming on ?

@hasanainmohammadismael4540 2 года назад

شكرا لك

@screwsnutsandbolts 2 года назад

You're welcome :)

@hasanainmohammadismael4540 2 года назад

@@screwsnutsandbolts May God protect you and take care of you

@A60-g5h 2 месяца назад

This is the switch, but where is the oilsensor located?? 😢😢

@screwsnutsandbolts 2 месяца назад

It should be beside or above the oil filter housing. It might be hidden behind some wires or plugs

@paulfreer1302 6 месяцев назад

Some what as thought it cuts out momentarily. Probably 1 second or 2

@paulfreer1302 6 месяцев назад

Did it ever break down because of it It happens in the first 2 to 3 miles then seems ok. Did yours do this

@screwsnutsandbolts 6 месяцев назад

No it never broke down. It wasn't really noticable when I was driving.

@paulfreer1302 6 месяцев назад

Yes very similar to my problem

@Bintang7cola8929 3 года назад

if it is broken .. what is the warning that always comes out.. indicator

@screwsnutsandbolts 3 года назад

I think you get an oil symbol on the dashboard

@anthonygreen9157 2 года назад

@@screwsnutsandbolts You get "Low oil pressure" words on the centre display panel.

@endritshehaj8188 3 месяца назад

Hey , have peugeot 307 2.0 petrol , it says low level of oil , but no leaks . What can the issue be ? Thank you

@screwsnutsandbolts 3 месяца назад

If the dipstick is showing the correct level of oil, then the oil level sensor could be faulty. It's usually located on or near the oil filter housing.

@garage3717 11 месяцев назад

Hello i have P040A fault code on my Peugeot 308sw 1.6hdi, description of code is: oil gauge fault, what do you recomend to replace or repair? Thanks!

@screwsnutsandbolts 11 месяцев назад

What did you use to get the code reading ?, when I look up P040A it seems to be related to the 'Exhaust Gas Recirculation Temperature Sensor' ?

@Roman-bg8zb 3 месяца назад

Mine is a 307 2.0 hdi and it's not located there and I cannot figure out where it is. Any ideas?

@screwsnutsandbolts 3 месяца назад

What year is your 307 ?

@Roman-bg8zb 3 месяца назад

@@screwsnutsandbolts 2003 3A/C, 107 horse power, 5 doors, hatchback

@screwsnutsandbolts 3 месяца назад

Apparently it can be in different locations. According to the manual "The oil pressure switch is located at the front of the cylinder block, adjacent to the oil dipstick guide tube (1.4 litre engines) or above the oil filter mounting (2.0 litre engines)."

@Roman-bg8zb 3 месяца назад

@@screwsnutsandbolts and it's not there. I've checked all around the oil filter area and it's not there. Mine it's a diesel.

@Roman-bg8zb 3 месяца назад

@@screwsnutsandbolts found it above the filter, hidden by 2 hoses and some wires. Thank you so much!

@alessandro17469 3 года назад

Do you need to drain the oil before proceed?

@screwsnutsandbolts 3 года назад

No you don't. A small amount of oil might trickle out from behind the sensor when you remove it, that's all.

@alessandro17469 3 года назад

@@screwsnutsandbolts Thank you.

@screwsnutsandbolts 3 года назад

You're welcome !

@nashawn92 Год назад

Hello, is it same emplacement for peugeot 207 ? Thanks

@screwsnutsandbolts Год назад

I'm not sure, I've never worked on a 207

@cihanates3210 2 года назад

hello, in my 307 car, it writes low engine oil pressure warning and it gives instantaneous when revs decrease. especially when the engine warmed up. If I replace this part, will it be fixed?

@screwsnutsandbolts 2 года назад

It could possibly be a faulty oil pressure switch. It's quite cheap to buy so I would change this first and see if it fixes the problem.

@eduardedy322 2 года назад

I have a problem with the oil light on the dashboard, it doesn't light up at all, atleast on ignition. The light itself works, it can turned on with tester, I also have a new switch. It should light up on ignition, right?

@screwsnutsandbolts 2 года назад

Yes the oil light usually comes on when you turn the key to the 'on' position and then goes off once the engine starts and you have good oil pressure.

@eduardedy322 2 года назад

@@screwsnutsandbolts the oil pressure is good, but the light doesn't come at all. Even that little oil meter thing works on ignition where the km's are

@screwsnutsandbolts 2 года назад

Yeah that's the oil level sensor reading. The oil pressure switch is the one that turns on the light if the pressure is low. Did you say you changed the switch ?

@eduardedy322 2 года назад

@@screwsnutsandbolts yes it was that piece that you shown in the video

@screwsnutsandbolts 2 года назад

Maybe one of the wires is grounding somewhere. I read this on a forum: "You should be able to check if its the sending unit by grounding the wire at the sender to the engine case. The oil light should come on (power on). All the sender does is provide a ground when there is no oil pressure. The sender could be stuck with the circuit open so you never get the ground signal."

@WanMohdAsraf 2 года назад

Hi. I have change the switch but on my display still shows Oil - - . It supposed to show Oil OK. How to fix that?

@screwsnutsandbolts 2 года назад

The oil level sensor could be faulty.

@WanMohdAsraf 2 года назад

@@screwsnutsandbolts i have change the sensor but seems like no change before and after change. Still have Oil - - warning

@screwsnutsandbolts 2 года назад

This video shows the oil pressure switch but there is also an oil level switch which could be faulty. Have you changed them both ?

@WanMohdAsraf 2 года назад

@@screwsnutsandbolts yes. Have change both

@Mr11ESSE111 Год назад

did hdi versions got that too?

@screwsnutsandbolts Год назад

Yes they should have but it could be in a different position on the engine than the one in the video

@Mr11ESSE111 Год назад

@@screwsnutsandbolts could this be reason why on trip computer (peugeot 207) can be low oil pressure messgae sometimes and car sometimes have hickups in driving !?

@acasm Год назад

hi, I have 307 1.6 hdi, and oil pressure indicator blinks from time to time on a dashboard, blink for a second and disapire, could it be a oil pressure switch? and do you know a location of this switch on 307 1.6hdi engine, thank you.

@screwsnutsandbolts Год назад

It could be a faulty oil pressure switch but it could also be a sign of something more serious. Check this link: www.sunautoservice.com/about-us/shop-talk/low-oil-pressure-light-on/

@screwsnutsandbolts Год назад

I haven't worked on the 1.6HDi so I'm not sure. It's usually located close to the oil filter housing.