Restoration direct drive capstan servo control // Restore old memorabilia 

I don't understand what kind of restoration is this if he didn't change not even a single capacitor. After 40+ years, electrolytic capacitors are done and need to be replace. Also belts and rubber parts needs to be replace and calibration needs to be done as well. This is not restoration, it's just a dust cleaning. Don't be fooled by this clip, restoration si far more complicate compare to this dust cleaning

Muito consiente,inteligente ,abrangente e aberto,parabens Mauro pela sua visão da vida,sim estamos todos no mesmo barco,mas realmete existem pessoas que usam de outra para "subir na vida",mas eu acredito na lei do retorno e da justiça não humana,mas divina,essa sim não falha,Deus abençõe !

You did an excellent job with the mechanical mechanism and cleaning, but I think you should have replaced the electrolytic capacitors because the device is very old

I've seen some of the restoration videos you've uploaded. This is the proper measuring method necessary for repairs, and there is no wrong way to check. I am thrilled to have friends in the field of electronic engineering. From Japan. Thank you very much for uploading to RU-vid.

Ein tolles Gerät aus der Vergangenheit, als Musikanlagen noch Spaß machten

Mantap mas broku acaranya semoga sukses selalu

Muito top, saber que tudo começou nesse equipamento, Pra evolução da tecnologia, e inspiração aos que temos hoje👏👏👏

Не надо наждачной бумагой по ходовому валу. А чистить надо контакты в разъёмах.

As a Audiphile....Congrats for this beautiful work..the best i see you doing......

Наш Дмитрий Коржевский растянул бы этот ремонт на 4 части 😊

Muy bonito tener un equipo de ésos,, eres un genio para colocar a funcionar tan hermoso reproductor felicitaciones.

Good morning sir. Analog recording it's used for in the music business. I had one of these many years ago. Same problem but no one could fix it here. Thank you for this video. Wow!!?!!

А кондеры поменять ? А настройка по тест лентам ? А переключить на одиниканал или другой поскольку тут запись в несколько дорожек ? По мне показуха а ни реставрация !

I have not seen one of these since 2002. We were still sending shows via courier to NYC on tape. I switched all our shows still using reel to reel over to digital and I uploaded them to NYC WE took our reel to reel machines out of service a month later and that was the last time I used one. The remote units plugged into CTCSS remote trigger units that turned the unit on and off. Back in the day we had 3 or 4 of these each with its own CTCSS remote trigger and we would record the entire weeks promos, talents, commercials and music and we had the CTCSS tones loaded into buttons on the console so we just pressed whichever tone we needed to start the next machine and we would have to put the stop tone on the start of the other reel. It took a list of the actions of each reel. WE would " head and tail" each cut. So the tail of the talent doing the intro into the song would have the tone to start the music reel and the head in the music reel cut would have the tone to stop the talent reel. It was a lot of work.

TAEC this is a great tape recorder

nice work

Разобрать, помыть, собрать, какое же это восстановление ?

Now that I have seen you do this, I might try to clean up my A 4300 ! Another very good video.

perfeito muito bom valeu gostei..se quiser manda um desses pra mim blz eu amo deck de rolo .valeu tmj.

TEAC was 50 years old, but it wasn't broken.⛩🚅🎴🎌

Mr Electric I would love try and repair my Sony receiver. One day when I get the nerves I will open it up. Thanks again for your video.❤❤❤

I forgot how modular these were. The headers and the 8 bit Isa PC slots, I totally forgot about this. They really were ahead of the time

Nice video but you should have put some kind of wood oil on that cabinet and then used jewelers polish for the front top faceplate...trust me, it works miracles.

PARABENS PELO BELO TRABALHO GOVERNADOR VALADARES M G BRASIL

Great dismantling. (and putting back together again)

Nice job!! Well done. You reminded me of myself when I used to service all tape decks and turntables. ❤

Quá xịn

good work but needs a full recap this machine

Ein tolles Gerät aus der Vergangenheit, als Musikanlagen noch Spaß machten ❤!

Coisa Linda De Se Ver

Very nice intelligent man

Another beast! Try to find some Carver amps to restore. They were made in mid 80’s.

Никаких замеров, реставрация на внешку .

Nice work!

Лютый треш! Тон-вал, ролики - наждачкой! Контакты - скальпелем, "измерения" - огонь! ) Подгоревшую плату с диодами не восстанавливал. А головы не убитые. Жалко аппарат.

Lol, I like the baby spider dropping down! He's thinking "I'm out of here!"

Nice job done

Congratulations for your work !

Your video inspired me to restore a similar Teac, but I was disappointed you chose not to show the screws (at least partially) being replaced. I found I had put the upper portion of the recorder back in the wood frame only to find I needed to screw down the black bar at the top "before" putting it back. Certainly my bad, but you gave no indication it needed to be done before dropping in the tape portion. I would recommend editing them in a way that gives some indication of all aspects if you are offering these as a help. It can still be done in less than 45 minutes if edited properly.

tenho um desse, está com problema no motor, que é diferente desse, é motor grande, quando dou impulso nele, ele firma, depois com tempo vou tentar descobri se é o motor ou o circuito. bom trabalho

Das was hier gemacht wird ist keine Restauration sondern in meinen Augen eine unnötige Verschlimmbesserung des Tonbandgerätes. Ich denke hier hat jemand Langeweile. Das Gerät war von vornherein in einem sehr gutem Zustand. J.S. Radio-Fernsehtechniker- Meister.

Ты крутой чувак 🤘🏿🤟🏿🧡🧡🧡😊

I enjoyed the cleanup and lube of this Teac. I do not recall this model but seems to stand out from all the more purely mechanical tape transports. I noted your cleanup of the reel motor drive units did not include any testing of the torque capabilities of the drive motors which appear to be good old brush type dc motors and not brushless servo motor design like the direct drive capstan motor? As I recall reading such motors are good for so many hours and then they start to deteriorate due to worn brushes. I would love to see how and if they can be restored because these would be a definite weak link in future reliability based upon how many hours are on them. Also the tape you used to demonstrate the machine is apparently recorded in a different formal because I heard some audio playing backwards on this 1/4 track format deck. But it is impressive the deck came back to life after complete disassembly, cleaning and reassembly..

Umabraço e o ❤

Japanese assembly of the highest quality, international level. Look at the quality of the steel sheets, they have not oxidized over time.

What was wrong with it except that it was dirty?

❤❤❤❤❤

This is a fantastic video. You seemed to be really skilled. Where are you located? Do you have workshop? Do you sell reel-to-reel used and restored Tape recorders?

gppd job

For all bearings, to much thin fluent oil was used. Wait when the oil meets the toneheads and the tape, the music will be really good. Moving coil instruments? No oil to the Saphire needle bearings!

Fiatalabb voltam általában meg javítottam a saját rádiómat, tévémet és magnómat,de ennyire nem mertem szét szedni mert nem tudtam volna összerakni! 😂 Ez szép munka! Az érdekelne, hogy a nyomtatott áramkört és a diókákat mivel mosta le, olyan volt mint a víz, de gondolom nem az volt, hanem talán alkohol?

Did you demagnetize the heads? In that case, good job. 🇮🇪👍

パートタイムの叔母さが組み立ていた。

Best way

Quasi ok, adesso le tarature e calibrazione nastro :)

Please don't mess with the heads screws that are pre aligned !

Добре, що не пофарбував 😂

i have two 5500 teacs they are very good got one when my akai 635d went down ..used it for years till i had a chance to fix the 635d ...

You are obviously Very skilled. I just wish you could have explained Exactly what you used during the process.. i.e. types of fluids you used for various parts cleaning and lubrication oils or grease. I have about 6 reel to reel machines in my recording studio (Tascam 80-8, Sony TC 355, Teac 3300, Tapesonic 70 DFT & TRSH etc.) which I would love to restore and I've tried to maintain them ; but the job seems overwhelming when you do a full "field strip" down to the chasis. Did you have a schematic?? Insofar as I'm down to my last box of magnetic tape, I'll just try to keep them running with alcohol & Q-tips until they die a slow death. But, very nice job.

Отличное видео 😊

❤❤❤❤

Increíble restauración! Otro espectacular trabajo, felicidades!

Não entendi porque o contador estava diminuindo.

Old electronic are built like cars. Mass production of those contraptions is a very labor intensive process, modern electronics offset this cost with ever more compact IC. Lithography is an expansive overhead investment, but it can bring down the cost with production capacity, which become much cheaper than running those assembly lines.

Würde mir gerne ein Grundig TK mit großen Spulen kaufen. Dieses Gerät konnte Audio in High Definition wiedergeben. Tolles Gerät. Nur es gibt keine Tonbänder mehr zu kaufen.

👍👍👍👍👍👍👍

Very nice work but the resulting audio quality is not good. Does the head need aligning? Or perhaps it's just a live recording and therefor there are extraneous sounds as well as the music. Well you did a terrific job of restoration in any case.

Это наверное конкурс - а спорим, что потом я смогу все собрать. Ну и дрова. Если бы разбирался отечественный аппарат - заплевал бы экран. Ну а так, наверное восхищаться нужно. Ну разве что фантазией изготовителя.

You 're looking at this antique ...someone likes to restore it..at the same time, why?.There are thousands of people doing this on the Internet...that nostalgia, the figure will win...it's all in the trash in 5-7 years...Or all to the museum

Is this Teac A-5300 for sale ??.. If so what is the price ??????

As it looks that this tape-recorder have many many parts, so how do you know the exact place of each part?

i have two 5500s great players

❤

RESTAUREI DOIS E UM AKAI .

Nice

そこまでやるか、、、、参った、、参った。

Никого не удивило,что смазывают подвесы рамок стрелок индикаторов??? Там нет трения, металлические нити подвесов скручиваются при работе ...

Never pull the wires, always pull the connector!

A6300持ってます。

Может кто нибудь сказать - а зачем он всё разобрал то? )))

👍👍👍👍👍👍💜💙💚

اين انت واين اراضيك كي تصلح لي بعض الاجهزة التي هي عندي مثل التحف ..تحياتي لك

Ik snap nu dat die dingen zo veel geld kostten; geen smid en metaal. 😂😂😂😅🥰🤭

Das was hier gemacht wird ist keine Restauration sondern in meinen Augen eine unnötige Verschlimmbesserung des Tonbandgerätes. Ich denke hier hat jemand Langeweile. Das Gerät war von vornherein in einem sehr gutem Zustand.

Шикарный аппарат

Musica estranha parece a musica da Xuxa tocada de traz pra frente

Bhai apko ye bechna hain kya

Sounds like the heads need alignment? You're picking up some interference from other tracks!

That power supply board looks a little burnt!

Музон жесть.

where can i buy

It is not restoration. It is maintenance.

Omg, what is that

18:44 - FFS...

There was a reason why these things have been discarded. Nobody is making tape for them anymore. Nobody's making pinched rollers for them, anymore. They converted over to Grab Rollers. Highrollers who grab. Not just the tape recorder. But it's other, accoutrements. We can tell by the sound quality of your playback. It is spectacular! And was well worth the effort. Of taking the whole thing apart. Just to make it look shiny new again. While it's not worth using. It sounds better and is less expensive with a, Internet, low bit rate, MP3 stream. Would sound better than this contraption. And not stick together when the tape gets wet. With your next monsoon season. When this recorder originally floated away. At least it has 3 motors and knows where to run to. But a direct drive capstan motor? How ridiculous! It'll never catch on. Why would anybody want direct drive when you could have belts and pulleys? Give me a call on your telegraph when you can make more sense. Or send over a cart of oxen. So I can look at their rump. And see if I want to stick my hand up it? And I will pay you, five Squid for it. Or you can clam it. Oyster you again! All of this nonsense is completely, un-floundered! And has made a whale of an impact. You have been urchin for so long. I won't, tilapia if you don't. I think I've had a, stroke. Of bad luck.. And I just met myself. Hi my name is Remy what's yours? RemyRAD

Happy Analogue Age

Um canal ficou mais baixo ...

Да….!!! Золотые руки!!! От вашего мастерства я упал в уныние. Есть же люди на свете. Желаю вам удачи во всех ваших делах!!! Храни вас Бог. Подписываюсь на ваш канал. Ваши ролики смотрю на одном дыхании.

😂😂😂 You just unscrewed the whole thing, clean the dust and reassemble it back. Do you call this RESTORATION...???