As mentioned by another, the Vintage switch only affects the bridge pup. When engaged it cuts out most of the lower frequencies, it's a bass cut effect not a treble boost. There is a Reverse Wind Reverse Polarity mod (RWRP) that can be done to the bridge pup with just a bit of research and skill. This mod will cancel out external noise when both pickups are engaged and fully up. It does not change the tone of the pups whatsoever. This is how Fender Jazz basses are wired. I've done this to two 4003 basses with excellent results. Highly recommended.
@@RezaPratamaR 4001 is basically the old 4003. Main differences are that the "vintage" switch doesn't exist on the 4001. It's basically just always in vintage mode. Older 4003s don't have the vintage switch either, not sure which year it was added. Those are basically always in 'modern' mode. The 4003 also has a double action truss rod which makes adjusting the bow in the neck a lot easier. Oh, really old 4001s have the 'toaster' pickups which are lower output than the pickups that are in the newer 4001s and the 4003s.
@@buzzardsinuses4780 sure, but in the recording used in the movie Scott Pilgrims part is played on a mustang and the awesome solo is played on a ric although the character is playing a mustang.
@@leemaddison1286 Yeah I think this may be kinda like owning an Alfa Romeo, part of ownership is knowing that it’s unreliable as hell and will inevitably break down within a few years
Fantastic review Scott. These videos are often full of people just bragging / showing off that they have one, but it was great to see a person telling it like it is, good and bad.
For that Classic Ric tone, the sweet spot can be found if you go all knobs maxed then back off the Bass volume until you hear a change in tone which will give you that Classic Ric tone.
What was confusing about it? He told us what he dislikes about the bass and his experiences with that particular example before a playing demo and presenting what he does like
I've never heard of anybody having the strings rattle against the top of the pickup cover. You'd have to have either insanely high action, or the pickup screwed down far far too low.
Who left the pickup cover in place? I removed it as I got it in mine. Yes the bridge is a pain the nut, but the bass is so solid, so clear, that the effort worth it.
I have a Ric 4003 also. When I got it, it looked incredible... but had a few setup issues. Actually 3 of my 4 Rics needed adjustments before I was happy. I always chose mine from shops that had them ready to ship... The instruments are quite unique. You'll either really love it, or you'll want to stay away. When one compares Ric's Pricing to USA Fender and Gibson.... it's competitive.
ive got to know this amazing bass by the 2000 anime Fooly Cooly (FLCL) and when i first saw the guitar when it first appeared i was like " wow thats a dope guitar" and man i still think to this day that his my favorite bass guitar ever
FLCL is one of the reasons I purchased my Ric. Love these instruments. I'm planning on getting another at some point like the midnight blue FLCL as mine's Fireglo
I have one, a 4003 Jet Glo. I have all the Original parts, I have not one single complaint about it. It's perfect. You do not need to replace anything on it at all. I use a Zero Mod thumbrest when using fingers, and when I use a pick I play behind the pickup cover and it's amazing. People tend to over think things. Rickenbackers are a completely different animal. Learn to play it, adjust your playing. Nothing wrong with these basses in their current forms.
I replaced the stock bridge with a brass Hipshot Rickenbacker Replacement bridge. This made a world of difference for tuning, intonation and adjusting the action but didn't change the traditional Ric tone. I don't know anyone that owns a Pic that leaves that pickup guard on.
Yeah, Ricks are pretty pricey nowadays. But, I'd definitely pay a couple grand for a new one if I could. I think they're worth every penny. I got lucky on price and waiting time when I got my 2 4003's. Got both of them from a discount house in Greenville, South Carolina. My father was friends with the guy who ran the store, so that helped a little, too. ;) I ordered my custom-made Jetglo around July of 1985 and got it September 17th. My custom-made Mapleglo was ordered July or August of 1989 and I got it October 2nd. Both guitars I got 40% off. Paid about $680 for the Jetglo with case, right about $1,000 for the Mapleglo with case.
TWO THINGS - 1. The bridge pickup cover is completely plastic. It offers nothing to the sound but gets in the way. 2. It is advisable to flip the bridge pickup and reverse the wiring on it. This will eliminate the hum. Google "RWRP Bridge Pickup Mod Tutorial." It is easy. No effect to the Ric tone. This is how Jazz basses are wired. When both pots are turned up, they cancel the hum. Yes, I waited several weeks for my 4003 S Mapleglo. Yes, it came stock with a odd gauge of bass strings you will not find anywhere else. Great bass, infectious tone. Not as easy to play as a Jazz or P-bass. Sometimes though, I just like looking at it :)
My friend bought his in 1993 and the first thing I did was take off that stupid plastic cover over the bridge pickup which does nothing except look good. If you look at most of the premium players of these basses, they do the same thing. That plate is placed literally right where you would be playing. Just take it off and store it.
The looks and tone are awesome (despite the pickups being a tad noisy by design). The construction and setup issues have kept me away from a purchase. I borrowed a friends 4003 and played at church (over 20 years ago) and it played and sounded killer. I just couldn’t justify the high spend due to QC issues that have been around since the instrument went into production. This is particularly sad to me as I started playing bass because of Chris Squire who was the best ever.
I've owned a few and played a number more. I agree completely about their build and quality issues. Their best ones are truly transcendent instruments, but it's a crap shoot as to whether yours will be one of them.
I wanted midnight blue also, i got it. But it was $100 cheaper than the other colors. I wasn't sure why, until someone told me that in the 80's everyone and their sister had midnight blue or cobalt blue. Let's stage a comeback!!!
BASS player here, thank you for sharing your experience, saw one guy on RU-vid setting the tross-rod on a Rick, WHAT A PAIN. I like the sound of those BASSES, iconic.
I have one and I love it. Rickenbacker don’t have a Far Eastern budget range so if you want one you’ve got to REALLY want one. I like that aspect myself. Stereo or mono outputs are very old school and although I have the stereo box and lead to use the stereo output I haven’t actually tried it yet. You can run each pickup to an individual amp using the stereo box and I want to use a filthy overdriven bridge pickup into one amp and clean bassy, neck pickup into another. I’m not into active systems and prefer passive pickups and use the amp to tweak the tone. Actives add too much complexity. I play Lemmy style and it’s perfect for Filth. If you’re into Jaco then this bass will annoy the hell out you. It feels more like a guitar than a bass if that makes sense. Live it turns heads and on one occasion a guy showing off his Jaco licks on a fancy bespoke custom 5 string was stopped dead in his tracks simply by me opening the case of my Rickenbacker. Ha!! Try one but you’ll have to work with it and adapt to its needs a lot more than you would with a Precision or Jazz. Overdrive brings it to life. Al Cisneros of Sleep gets an awesome sound from his.
Metal Scott, your video had much truth. I purchased several new, 4001 and 4003's. The common denominators were unstable intonation, thin twang sound, uncomfortable when performing, bowed necks.....truss rod's never set correctly, difficult to set up bridge, nuts incorrectly cut, etc..... Why should I need to reset factory settings on a $2,000. bass ? For my money, I have always been completely satisfied with Fender Precision basses.
I understand this video is 2 years old so I’m gunna clear a lot up. First- it’s pronounced Ricken- BACKER not BACHER. Second- warranty is 5 years not 3. This guy clearly knows nothing about string gauges or did any research on the RIC factory recommended spec, he just bought strings and slapped them on like it would change anything but it affects everything! Third- if you adjust your action, YOU CAN ADJUST THE TREBLE PICK UP TO MATCH, eliminating this guys buzz on the cover. Or remove the cover and move along. Fourth- RICs back log is based on demand not controlled substances. What a weird thing he “discovered.” RICS operation is super small compared to other companies, we’re talking less than 50 employees and that includes office staff, so the back log is just not having the ability to keep up with demand. Fifth- the price is very average if not less expensive than an American made instrument in the “high end”category. Don’t believe me? Look at Musicman, Gibson, and Fender American, CA made instruments. My final points- parts and components can move and break in a few years, happens on instruments all the time, so your pickup issue isn’t that uncommon realistically especially if you’ve dropped or banged the instrument of accident. Also RIC fixed all the bridge issues with a new bridge developed and released in 2019 called the V2. Rattling, difficult intonation, tail lift all solved.
Thanks ... I was gritting my teeth at his ineptitude and ignorance ! Why publicly review an instrument that you clearly know almost nothing about, including use, nor the maker ??? He was actually surprised that he could get different tones and sounds by moving the knobs, which evidently he hasn't done before as he is in 'normal mode' ... ! hahahaha. They're great Basses ... but admittedly not to everyone's taste. You can get unique Ric sounds out of them. This guy should learn how to play Bass and how to deal with adjusting the setup as necessary before 'giving judgement' on something he is uninformed about ...
Nice! I have one of those too. I think it was 2001 when I got it. Paid just over $600 for it. Now it's over a G ones you get a case for it. Back then I used to play a lot of not so much any more. My sound guy always used to complain about how hard it was to record the Geddy Lee bass because it has so much low-end. If you like Rickenbacker and you like Fennders, you probably like the S1 Jazz bass it's like jazz bass that has Rick O Sound button.
Have a 2007. Never had a problem with mine and I gigged it hard for ten years. Never had a rattle. You can't approach and maintain them like a Fender. Mine has been very good to me considered how much I put it through...all it needed was a quick job once a year. Between it and my 1980 BC Rich Eagle, I have all my bases covered for whatever gig is on deck. Run it through an Orange and it's perfect.
My $450 Squier Bass VI has no problems at all. I didn't shim or mod it at all. Bridge intonates perectly, no fret buzz, no truss adjustment needed. But, as usual if you go on the forums everyone immediately takes apart their bass and shims and replaces every part on the thing...I'm not so sure about people frankly. Anyway, thanks for the review, I no longer lust for a Rick...they do look cool AF tho!
I used to have a white 4001 with black binding, scratch plate and headstock name plate and the logo in raised white lettering. I loved it and it was my first dream bass. First thing I did was to remove the bridge pickup cover. It just gets in the way and restricts different plucking positions and styles. This was a beautiful bass and nothing else was going to get me that vintage ‘ricky’ sound. However, in the late eighties I got into fretless bass and the Ricky stayed in the case! I then transitioned and developed into more blues, jazz and funk styles and my bass collection grew with a Schecter fretless 4 string and a Yamaha BB1500 (also in white). Then I came across a beautiful 5 string Fender Jazz Bass Plus. This model has no scratch plate and is a gorgeous tobacco sunburst colour. It is active with a passive option and the control knobs are in a parallel orientation to the strings rather than the traditional slanted configuration. It looks really unique whilst clearly being a quality Fender. This has a classic Jazz Bass Sound with the ability to get excellent tonal variations including a mid-boost setting using the active EQ. The Yamaha was quite good for slap styles but I found it a bit clinical sounding after a while, whereas the Jazz Bass has been far warmer and more usable. So I sold the Rich, Schecter and Yamaha in favour of the Fender. I’ve added an electric upright 4 string by Dean and I recently acquired a 5 string electro-acoustic 5 string which I’m going to convert to fretless! I’m sad I had to sell the Ricky, but I still have the bridge pickup cover as a souvenir! Thanks for making this video...
The E string gauge factory supplied is 105. I made the mistake of getting a wrong sized set, but rather than hacking away at the nut on my cherished, beloved and expensive 4003, I looked into it and bought the right gauge of strings! The other set will be fine for my old bass. Ricky set from factory is 45-55-75-105.
I had a metallic blue one. SWR 900 head. It was nice. Just never felt like I was in it when playing it. Felt like I was on top or pushed away from it. I still like them.
Not sure why he's using the push/pull on the neck pup since it only effects the bridge. Also there's no effect from the tone controls on the opposite pickups, though he's changing the settings as though there is!
I got my Rickenbacker 4003s and while it took me a lot longer to properly setup than my other basses, it plays wonderfully, sounds great, and I have none of the issues you mentioned here. Guess it all depends on luck? But nah, I absolutely love my Rick.
Literally the best bass setup I've come across and now use is a cliff burton set up (not the pickup mods lol). Basically use light guage strings and remove the pickup cover. Plus if u want, get a thumb rest for the ric, they're pretty neat.
Very distinct tone, lots of character. Works great on certain types of music, if you write your own songs, play progressive rock etc... but I found a P or a J works much better playing in a cover band where you cover different styles and eras. A lot times on the Rick it's like where is the midrange? The tone is very scooped and trebley.
The scooped and trebly tone you're referring to is only noticeable with *both* pickups on... reminiscent of a Fender Jazz. But when you're using the bridge PU only, you're in midrange heaven! Cuts through EVERY mix. Listen to McCartney's "Silly Love Songs" or his "Wings Over America" live album, and you get the idea... ;-) So "lack of midrange" is *not* the reason why a Rick doesn't sit well within your cover band context: It's rather the lack of punch, attack and overall "definition", which again is due to the instrument's construction (neck-through, shorter scale length, questionable hardware etc.). It's a singer, not a dancer. As much as I love my Ricks, a 4001 and a 4003, I can only agree with your statement: When you're playing Top 40, a good J or P is the bass you need.
@@kiwibass I think we're saying the same thing. Mid range is a very wide spectrum. So when you say "punch, attack and overall definition" to me that describes mid range to a T. Maybe it's upper vs lower or you mean something else. Or I mean something else. Geddy Lee always cuts through, as does McCartney, I much prefer his flat wound tone on a Rick. I just feel liked they are voiced to have low end and razor sharp treble and nothing better when it's working. P bass is low mids and high mids, not boomy and not brittle. Never clashes with the other instruments.
@@rrdream2400 Well, we're *almost* saying the same thing... or at least reach the same conclusion! ;-) What I meant by "punch, attack & defininition" was not so much the frequency range per se, but the dynamics (or "envelope") of the tone - or how "fast" the instruments responds to your fingers. Musically speaking, it's the rhythmic information in the audio signal. As it's hard to put in words, let Geddy Lee be the perfect example: He was switching over to a WAL when Rush decided to take a different rhythmic approach... opening up to "world music" elements and generally being a bit more"funky". Try "Big Money" on a Rick, and you know what I mean... ;-)
"I'd expect that from a squier" Nahh never had those problems with any of my squiers, and even then getting a good setup on them takes no time. Also focus on a groove man! Cant really appreciate the tone if you're travelling the neck like you have to show off every note or something.
Not necessarily in this order: Learn basic guitar setup procedures. Learn Rickenbacker peculiarities. Learn to play. Practice your presentation. THEN make a useful RU-vid video......Misleading and incorrect information doesn’t help anyone.
@@JP-mu5ic Yeah no, “distinctive in nature or character from others.” AKA instruments with heavily compromising faults that are absolutely unacceptable for such high prices. Exotic woods and whatnot are peculiarities, a bridge that can't be intonated and crap finish are faults...
@@rickleblanc8900 he deserves it because he bought it. I'm a sucky bass player and imma buy one cause I want one. If I were to wait till I was an amazing bass player id likely never buy one.
Not Sure if you will see this comment since its been awhile since the post, But I do have a legit question. My bridge pickup just went out also. What was the issue with yours and how did you fix it?
I still see every comment. I just made a rule about not responding after about 6 months for anything aside from direct legitimate questions. Which is probably good considering the overall negativity in this comment section. The problem with mine ended up being a dead solder joint. They have a different coloration when the connection is dead. So basically just pop off the pickguard and look for the odd solder joint. Mine is actually acting up again so I might do a touch up all around now that I have a nice soldering station and a much better knowledge of wiring. If wiring isn't something you're familiar with you may want to try a local music shop if possible. I hope this helps! And I hope yours gets fixed!
@@robotromance5470 Thank you very much for the response. I will take a look at my wiring a bit closer. I already looked and and it seemed fine but i did not look for a odd color in the wiring. That is a great tip. Thank you.
The reason you wait is a marketing strategy. They maker fewer so everyone wants one it has little to do with lacquer. They are not well made, they are pretty bad, but.....they have a very distinctive sound, like no other bass.
There are some rickenbackers that are made pretty well. But most years do have the most faults. 2012 was rated the best year for rickenbackers and the new 4003S/5 is their best design. It's a shame how they are very inconsistent.
1000% agree, and him not being able to use his pinky and his tiny hand slows down the flow and makes his playing sound really jumpy and quite bad if I’m honest :(
@@carlitoxb110 not worth dealing with so much technical bullshit it is just not worth it. Are we going to play bass or self-teaching luthier courses. Don't get me wrong it is obligatory that you must know how to maintain the current instrument that you play but I prefer to play the damn thing rather than dealing with its imperfections ...
Never had an issue with mine-a 2007 4003. I put mine to work hard for ten straight years. Other than a seasonal tune up, mine was good to go. I used it for everything. I did have a 4004 for a short time but the neck would not settle down unlike my 4003 so I sold it. Picked up a 1980 BC Eagle so between the two, all my needs are covered.
@@MrMItzi-cc3xo agreed. Nowadays any bass with two splittable humbuckers will be able to get pretty much every time you’ll ever need from Jazz bass to Ric.
90s 4003 owner here: owning one of these is like owning a lambo or ferrari. its awesome, but you know its not as a good as a toyota or honda in some ways and you're going to deal with a lot of hassle. worth it.
If you want a solid body bass with two single coil pickups that is famous for a bright rockin' twang get a Fender Jazz bass. Way less troubles and issues.
Definitely a guitar player...lol but I appreciate your honest review. People make smug remarks about letting a professional set up the bass, but really - any other bass can be reasonably easily set up by the average player and I can't see why Rickenbackers have to be any different in that way. For me this is like glossing over poor design, a recurring theme on Rickenbackers. Wait until you need frets replaced, which will totally ruin the fretboard binding. As I said, thanks for having the courage not to let the Rickenbacker's cult status blind you to its faults. Thumbs up from me!
I think a lot of the push back on this video isn't necessarily that Rickenbackers are perfect but that he spread false information such as the vintage circuit doing nothing for the neck pickup although he insisted that it did and his strange complaints about intonation which, yes, there are many issues with setting up Rickenbacker instruments but what he cited was not an issue that many people run into (aside from the nut) and comes down to a poor setup on his part. But you are correct, these aren't perfect instruments in a similar way to how Jazzmasters are a massive pain in the ass but it's partially because of this that these instruments get the love that they do, weirdly enough. Oh! And his delivery is fuckin' weird.
My fix it guy taught me how to do basic mainentance. Never had a problem. I ran mine really hard for ten years before I got my 1980 BC Rich Eagle. Between the two, they cover any gig I have.
@@lurtz8656 Everybody I ever know who had a Bass in his hands basically stated "Rickenbacker lookin' great, soundin' good, Lemmy plays one - But the Bridge mate ... The Bridge ...". So his complain is pretty much on point with that. Sure, if you have somebody who told you the tricks beforehand it's kinda "easy". That he got the Stuff about the Circuit semi wrong, well ... idk, most people can't explain to you the difference between Fuzz, Distortion and Overdrive - And while Overdrive can sound kinda like Distortion or what Hard and Soft Clippin'. Personally, I like the design of Rickenbacker but I wouldn't spend even half a Grant on them. But I'm also not US American so ... there's also no real nostalgia to it for me besides of "Well, Lemmy had one."
When you're talking, I hear lots of hum in the room...but when you play, I hear no hum at all. I have a Rick, and it hums like crazy. How did you get it humless in the recording? Thanks.
I'm going to purchase a Mapleglo 4003s soon. As far as the modern/vintage control, I'd leave it on modern, the vintage just sounds too thin in my opinion. I really enjoyed the video.
The main difference between the 4001 and 4003 is the truss rod(s). When the 4003 was introduced, they abandoned the old "hairpin" rods in favour of a more conventinal design used by Fender and countless others. They both have their pros and cons, but the old hairpin rods were often used the wrong way, by people who didn't know what they were doing. Almost every 4001 has suffered fretboard separation near the nut... just as almost every Les Paul has suffered a headstock break! ;-)
You need 2 change the nut and the bridge for a hipshot, remove the metal bar from the pick up and I suggest changing also the pick ups for a seymour duncan pick ups. I have a rickenbacker and change that and now it sounds awesome
A buddy of mine has a 4003 with the Seymour Duncan Lemmy signature pickups and that thing absolutely rips. He runs it through a Matamp GT200 and a 4x12 cab; it’s probably the most righteous bass tone I’ve ever heard.
FYI- in 2014 May it took 10 days to get Midnight Blue from SamAsh. com & 10 days for Walnut in November. In 2018 it took 6 weeks to get #3 of 25 FabGear vintage SnoGlo. I have none of the issues mentioned with all 3.
I bought a brand new 4003s in 2017 and its been a great instrument. Bought it on eBay from a guitar shop in Memphis somewhere, they had it in stock, unlike the excuses I got from the local shop that would "order one" for me, which "could take a year", I was like, nah. I wanted to buy local, but whatever. I got it in a couple of days, Midnight Blue..... Rics are a "bass player's bass", in my opinion. The neck is super long, so playing notes down on the neck is difficult, especially as I get older. I didn't have any issues with mine. I use D'Addario strings (replaced the strings that Ric sent with it, pretty much immediately). I took all the unnecessary hardware off and powder coated the chrome to black, replaced the white pickguard with black, and changed the strut rod cover from white to black. I know that they can sometimes have issues; luckily I didn't have any trouble with mine, but I did take it to a luthier and he did some adjustments to it. It is an iconic instrument for a reason and I really like the idea that they're still made in the USA, which is rare these days... Although they should not be in CA, especially when there's an (idiotic) restriction on "lacquer" (seriously?). There is truly nothing I've ever played like a Ric, and not just the sound, the construction is very solid. My brother has collected several basses over the years, but when he picks up my Ric, he says "Wow, this is an incredible instrument", and he's exactly right.
The dual truss rod sounds like a great idea until you realize they’re both single-action only truss rods and Ric themselves state in the manual that to adjust the neck you have to first bend it into position and then adjust the truss rods to lock it in place. No other bass or guitar requires this.
Yep , And years ago when I owned a Rickenbacker bass I had no end of trouble with the neck… And then that’s why I got rid of it and just bought a fender .
The newest Rics now have a single truss rod system like other basses, to eliminate any and all truss issues (this is a VERY recent change). I guess it takes them 50 years to respond to players’ needs. Bridge problems are the other big complaint, but replacing with a Hipshot bridge corrects that.
Have you ever thought about building a Rickenbacker bass guitar from a kit ? From what I seen on RU-vid, They are very high quality and the guy who built his didn't have any annoying fret buzz.
Have you tried using the dual truss rods to set slightly more relief on the bass side of the neck than the treble side? You might be able to get a lower action with less rattle that way.
Back in the early 80's I had a Rickenbacker 4001 that came to me in perfect shape, including the setup. Back then I was a teenager and didn't know much about setup. The first thing I did on my Rickenbacker was take off that stupid bar over the bridge pickup. I like playing in that area and that thing just gets in the way. Why anyone would keep that on is beyond me. Older Fender bases had some of those two. My friend has a P-Bass with one on and it drives me nuts to play it because so many sounds can be made by playing by playing at different places over the pickups and near the bridge. I think the only thing I don't like about the Rickenbacker is the lacquered fingerboard and neck. I'd rather have have them oil rubbed rather than a finish. I currently only two bases and with the cost of everything gong up (I bough my 80's Rickenbacker 4001 for $650 but could sell it now for $7,500 because it had Grover tuners and a checkerboard binding that is very rare) so my current basses are two $500 Squires where i upgrade like I would a computer. The first thing I replace is the original bridge with a Badass II or a Kickass bridge. Basically a high-mass bridge for better sustain and clarity. I also put Seymour Duncan Quarter Pounder pickups in my Jazz Basses and they sound awesome. My most recent purchase is a 40th Anniversary Squire that has pretty hot pickups to begin with so I'm not sure I will change these ones out. Regardless my two Squire bases are upgrades to the point of at least a mid-level bass and they sound and play awesome. My next bass purchase will likely be the Geddy Lee Signature Fender Jazz Bass. It's still less expensive than the Rickenbacker; although at some point I very much want a Rickenbacker again. I loved my old one and certainly wished I never sold it.
If a better manufacturer would directly copy the pickups sound Rickenbacker would have nothing left but their looks. I hate that I still want one after years of hearing mostly negative stories and how often they’re garbage straight from the factory. Saw one in a store once but they wouldn’t let me play it, suppose they don’t want you to come to your senses and buy a used Fender that’ll actually work forever
I had a Rick 4003 (2019) and it was a POS. It broke down on the first gig (pickups) and I had to pay to ship it to Rickenbacker & wait 4 months to get it back. Then it broke (pickups) again the very next gig. The shop I bought it from finally decided to give me a refund.
see if you can get a feeler guage under the tailpiece. trouble ahead if so. i thought they were cut out by computer, now. finished by hand. i've seen some new basses with no lacquer on fretboard.
Interesting. Never had any intonation issue with my Ric or anything mentioned. I must be fortunate. Love the tone. I like a bit of fret buzz for some applications. So far so good.
Everybody points at Geddy Lee playing one of these, but he never really played one all that long during Rush's long history. Mostly Jazzers and for a time a Wahl and Steinburger. And the Jazz was used in the studio even during the Ric period.
Not all that long? It was his main instrument from '75-'83. We're talking the Fly By Night through Signals albums. Not exactly an insignificant period in Rush's history.
Geddy pretty much devoted a book to the fender jazz bass. I had the same luck he did, walked into a pawn shop got an American jazz for 200.00 after a new bridge and getting the truss rod "unstuck" I got the bargain of a lifetime, nothing quote sounds like it and I will never get rid of it .
Own 5 4003 s 1 with Thunderbird pick ups to get the Limmy sound 1 with a Di Marzio Mudbucker a SD stacked jazz with a Strat pu where the sting mute is 1 with Alumbic set up in then two stock but I take the pick up cover off and never had a problem with any of them
Rickenbacker isn't easy to setup, that isn't something everyone can do, especially if it's the first time you came across one of these. I hope you'll take this comment as a construtive feedback, give the bass to someone who knows how to set it up, put proper string gauge (45-105) and than, with your mind free from prejudices, make a review about it. While listening to this "honest" review, I can tell all the negatives, are just about a wrong setup.
As I said in the video, I did actually get the setup on it exactly how I wanted it. It just took time. A lot more time than anything else I'd setup. With several problems I didn't expect. The main point of talking about it the way I did was to highlight the problems I had and get people to know that they could also have these issues.
I bought a new 4003 in 1982. The action was set up perfectly from the shop, and this bass feels and plays better than anything I've ever played. However, I have to turn my amp up to 11 to get it to bark! It has BY FAR the weakest pups ive ever heard. Is this normal?
Rickenbacker doesn't use lacquer. They use a UV cured polyurethane. I have 2 - 4003's that I got a major deal on when I bought them used. I have the JetGlo which is the black. I also have the 4003W which is the maple neck and the walnut body. It has no polyurethane on the body, it just has oil rubbed into the wood. The black one has the modern bridge with the saddles, and a single truss rod. The 4003W has the traditional Rickenbacker bridge and a dual truss rod. Call me crazy, but I actually like the old bridge and dual truss rod better, but some really hate them. It's easier to adjust the action, and can get it a lot lower on the 4003W. I did have a Rickenbacker 4001 when I first started playing, because I am a major Rush fan, but I didn't;t know what I was doing because I was young and traded it. I don't have any problems with the Rickenbacker's. Love the Midnight Blue on yours!
Love the looks and some of the sounds of the Ric, but I just couldn’t get comfortable on my 4003. Hated the lacquered neck and fret board and the body just didn’t feel comfortable. I really wanted to like it but it didn’t work for me. My bridge p/u also went south.
I always wanted a Ricky to add to my collection, but the price tag is unjustifiable for an occasional instrument in my case. So a couple of years ago I bought a couple of cheap copies (a black one and a fire glow) for about £150 each. With cheap instruments, the weak point is usually the pickups and wiring. Necks and bodies were fine, very playable. bridge was a more conventional design, so better than the Ricky bridge! The treble pickup is actually a J bass type under the hand guard, so swapping that was easy. Seymour Duncan quarter pounder please! Had to get a Brandolini for the neck and replace the tone/volumes/switch but that was straightforward too, there are kits out there to replicate the Rick 'o Sound wiring. All in each instrument was upgraded for about £200, add in the original buying price and I got a pair of perfectly serviceable Ricky type basses for a fraction of the price of the real thing!
Same thing I did with a Johnny Ramone Mosrite Chinese copy. Just ordered a Dimarzio for it. Plus about to get them to build me a Nikki Sixx Warlock bass. Chinese copy is the best option for guitars they don't make anymore
i've been playing Left Handed 4003 and 4003s and 4001 and 4004 Rickenbacker 's scents 1998 so yea there not cheap and i have got them between 8 and 12 months to get it. But They are a Great Bass and worth the Money and Late
I've been playing left-handed 4003, 4003s, 4001 and 4001s Rickenbackers since 1998, so yeah-they're not cheap and I had to wait between 8 to 12 months to get them. But they are great basses and worth the money and the wait.
