Samsung Gas Range Install | Step by Step Close Up View | How To 

This is VERY important. Thread Sealer is used only for NON-COMPRESSION connections. You SHOULD NOT use thread sealer on COMPRESSION joints. If you use thread sealer near the compression joints, you endanger the chance that the thread sealer will get between the COMPRESSION contact point.

A technician tried to charge me $500 just to disconnect the gas stove and then reconnect it a day later (I was getting my floor done). I told him nah, this video helped me out and saved me $500

Brass fittings are soft, If you over tighten them you will break snap and crack. You should tighten it up enough that it is not leaking and that is it. You should also not use adjustable wrenches but the proper size ones. For a half inch kit you will need a 7/8 wrench and a 15/16 wrench.

Thanks for making this video sir. You just saved me $173 dollars in installation cost.. Lol

The part you are screwing into the back of the stove is an "adapter." Both ends are "male" ends. The part that screws into the stove has MIP (male iron pipe) threads. When you use MIP threads, you MUST use pipe sealant or teflon tape to prevent leaks. Think of the sealant as making a gasket between the male iron pipe threads and the female iron pipe threads. I much prefer pipe sealant than teflon tape because I have never had any leaks with sealant. I have had leaks with teflon tape. In my opinion, Teflon tape makes it easier to disassemble parts, so that is a plus. On the other hand, you can wrap the tape in the wrong direction so that it unravels when you turn the male part into the female part. That does not happen with pipe dope/sealant. In my opinion, both teflon tape and sealant act as lubricants making it easier to turn the pipes or fittings. This may help to make a better seal. On the other end of the adapter is a "flare" fitting. A "compression" fitting is a different type of fitting. I don't think that there are compression fittings on brasscraft hoses or adapters for stoves. Logically, I cannot argue against pipe sealant on a flare fitting. Some people say that the sealant can come loose and get blown into a gas valve. I probably have a better chance of getting bit by a shark and hit by lightning at the same time. The natural gas pressure in a residence is about 0.25 psi. That is really low. My bike tires are 100 psi. Pipe dope in a flare fitting might act like a gasket between the male and female flared surfaces. I think Teflon tape would hinder a good connection between the flared surfaces. I have been taught not to use pipe dope on a flared fitting, but I cannot logically argue against it. And yes, I know the difference between pressure and flow rate. Pipe dope is not combustible. Just for the sake of discussion, the threads on the flared side of the adapter are not MIP threads. This helps to make sure that the adapter gets installed correctly. It would have been helpful to see the female side of the flare fitting. You are careful to clean the male side in the video, but what about the female side? It could have crap on it. Thanks for making the video. It takes time to make videos and viewers like me appreciate the effort. It was clear and helpful.

Thanks for sharing this is a great video! I love the thoroughness and attention to detail you put into this installation!

could you post a video how to connect the hose from LP gas tank to a cooking range ...to convert from natural gas to LP gas

You might add that before you hook up the gas line you should put the range all the way in its space and make any leveling adjustment that may be needed. This is important because if you hook it up and find you have to move the stove in and out of the space to make leveling adjustment you will "work harden" the brass hose which could cause a leak in the hose. Years ago, this was a common occurrence and because of it the put a plastic covering on the hose to contain any leak. In any event if you periodically move your stove to clean behind it you should consider replacing the hose every once and a while.

You're over doing it with the tighting, you're lucky it did'nt strip or snap

This guy has a sense of humour

I bought the BrassCraft too. I went ahead and bought the BrassCraft leak detection solution. I also get paranoid about gas. I’m getting rid of my Samsung cos they aren’t reliable. I bought a Frigidaire Gallery Air Fryer gas range. Thank you.

I have the same stove , so this helped me a lot !!! Thank you 🙏🏽

Thanks for the great video! but the soapy water with bubbles may be confusing in case of a leak ( no bubbles on the soap to be sure of a leak or not )... other than that it is a great video.

Great video. I’m doing this in a few days. I may still put some dope on the bottom of the flared threads though. Call me paranoid 😂

Great video thanks, I would recommend using a 60:1 ratio when making soapy water solution, u wanna start with no bubbles and barely any soap so u can tell if there is a leak it will still bubble up with barely any soap.

Thank you for this video dude !! Super informative!!!!!

Get empty spray bottle and fill with soapy dish soap and water. Spray on gas fittings see bubbles ,tighten or get more fitting tape to stop leaks

Thanks, I never knew about the thread sealer.good example.

What about the brass gasket you were holding with a rubber insert on the inside?

Waow !!! !!! Was advised to simply use a clamp to assemble gas hoze with oven's conduit ...

Safety safety safety.... Why didn't you install the Safety excess flow valve that comes with the gas hose ? 3:01 its on floor on top of bag

The gas outlet was too high the stove won't go all the way back against the wall, so it sticks out further than the counter.

When connecting it, it's a good idea to turn off the main gas in case the valve is opened by accident. The valve is good for if you are working inside the appliance but not disconnect the gas hose.

Does your range stick out because of the pipe? mine has about a 2 inch gap.

The idea is to start with no bubbles..

Dos this kit include a adapter for the fitting

Hi I’m like your video and have a question is this range ovens use power or only gas . Thanks

I can’t get a light. I had my gas set to off for a few months. How long before gas starts flowing again? Thanks

That's a nice cooker

Can be use Teflon

My gas line is on the floor. The old stove cleared it okay but I just had my new Samsung stove installed and it is sticking out of the wall about 2 inches. He said because of the water line..? which is actually up against the wall behind the stove. Should this be pushed up against the back wall? The gap is horrible looking.He left and now I am afraid to move it back.

So, no sealant between the coupler and hose on the stove side?

I noticed that all the connecting hoses/kits that I have seen so far are yellow in colour,is there any particular reason for this or it is possible to get it in other colours.

This is "kinda" gas that you're working with! Remember that....

well done

What about leveling? Does the rear legs level also, or just the front?

So after 20 minutes. You got one whole line connected and oh i guess you were smart enough to plug it in also. So two things in 20 minutes that shoukd of taken 30 god damn seconds

Thanks!

Hello what type of gas your stove use?

Are 1/2'' OD and 1/2'' flare the same?

Watching this guy with 2 adjustable wrenches is like watching 2 old people trying to have a baby

Did u check the oven as well. I'm really concerned of mine.

Thank you for sharing

Too bad you did not show the leveling procedure.

Does the thread tape work as a good sealer?

Sir I need one of those hose, 12 feet long!! Where can I find it ? Help please

dip leg?

Does anyone have a Samsung with a very tiny gas in-take hole? I got no help from the store where I purchased it (my fault for going with a big box store). Turns out, the hole for the gas line in my range is only 1/4 inch inside diameter! Do I need to send it back? This seems smaller than anything I've read on the internet.

My pipe doesn't have the shut off valve. What pieces do I need for that?

You didn't install the safety valve that comes with package. Don't do what he did.

Whats confusing about this video is that other videos I have seen say specifically not to use sealer on the flared fittings. Please correct this video so that others don't get leaks or have problems. Thank you.

$329 saved.. just for someone to disconnect and connect.. NO THANK YOU

Hello. The shutoff lever from the air pressure on the regulator should be up or down? Dont know if its on or off the manual didnt say nothing.

You used the wrong pro dope. Not rated for gas.

Seriously what kind of genius uses bubbles to check for bubbles? 🙄

Not the same damn regulator

You needed the blue dope. Dangerous

so you use goop on the one on the stove but not even tape on the second one, same threads that leak bud, come on this video is going to make a lot of people have leaks, ,,,,,, jezzz