Samsung Top Loading Washer Out of Balance Spin Cycle Repair/DIY FIX/Suspension Rods Replacement

Подписаться 624

Просмотров 79 тыс.

50% 1

If you have a Samsung Top Loading Washer that keeps going out of balance on the spin cycle this video will show you how to repair it. The parts are about $50.00 and it could save you hundreds over calling a repairman. I did the repair in about 30 minutes. It involves replacing the "suspension rods" that support the tub in Samsung top-loading washers. Some people call these "shocks" but suspension rods are the proper name. You will also need a tube of White Lithium Grease. I bought mine from Home Depot for about $8.00. The rods were $40.00. Before the repair, my washer was completely unusable. After the repair, my washer worked perfectly. You will need only a few basic hand tools. These include a thin, stiff, putty knife, a pair of pliers, and a screwdriver. Please wear old clothes and gloves as the old grease is pretty ugly stuff. If you are fairly handy this is an easy repair. Thanks for watching. This is my first video but many more will follow on a variety of subjects. If you subscribe and like the video it will be easier to find the new videos. Thanks, Dan
Below is a link to the suspension rods I ordered from Amazon
www.amazon.com/dp/B09HL8TC5Z?...
Amazon shows the following models as being compatible with these suspension rods.
Model Compatibility 1: WA19J3000AW/AX WA400PJHDWR/AA WA40J3000AW/A2 WA40J3000AW/AA WA422PRHDWR/AA WA456DRHDSU/AA WA456DRHDWR/AA WA45H7000AP/A2 WA45H7000AP/AA WA45H7000AW/A2 WA45H7000AW/AA WA45H7200AP/A2 WA45H7200AW/A2 WA45M7050AW/A4 WA5451ANP/XAA WA5451ANW/XAA WA5471ABP/XAA WA5471ABW/XAA WA16J6710SS WA476DSHASU/A1 WA476DSHAWR/A1 WA484DSHASU/A1 WA484DSHAWR/A1 WA45N3050AW/A4 WA45T3200AW/A4 WA45T3400AP/A4 WA45T3400AV/A4 WA45T3400AW/A4 WA50R5200AW/US WA50R5400AV/US WA50R5400AW/US WA50T5300AC/US
Model Compatibility 2: WA19J3000AW WA400PJHDWR WA40J3000AW WA422PRHDWR WA456DRHDSU WA456DRHDWR WA45H7000AP WA45H7000AW WA45H7200AP WA45H7200AW WA45M7050AW WA5451ANP WA5451ANW WA5471ABP WA5471ABW WA16J6710SS WA476DSHASU WA476DSHAWR WA484DSHASU WA484DSHAWR WA45N3050AW WA45T3200AW WA45T3400AP WA45T3400AV WA45T3400AW WA50R5200AW WA50R5400AV WA50R5400AW WA50T5300AC

Хобби

Опубликовано:

29 май 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 163

@douglasfortin387 Месяц назад

You know, it's the testamonial at the end that really makes this vid worth watching. I've been avoiding house calls like mad because i KNOW I'm probably going to get the shaft--get it--and would probably be better off researching. learning and doing myself--of course, IF at all possible. I have had great success in the past, and because of vids like these, I know I will have more successes than failures in the future. Thanks Dan!!

@danfixeseverything 27 дней назад

Thank you.

@norview71462 4 месяца назад

Ordered the tension rods from Amazon & followed this video & got my washer back working for under $50 & about an hour of work. Thanks for this video !

@danfixeseverything 4 месяца назад

Happy to help. I am glad it worked for you.

@billybradford 8 месяцев назад

I was out in the garage cursing at our washer as I tried again, in vain, to balance the load of clothes. I was ready to call some repair folks (I am pretty handy, but was just not in the mood to fix anything) when my awesome wife came out and said "Hey look at this video I found! It sounds like the same issue we're having and it's fixable!" Now the washer is opened up, the springs are out and I am waiting for Amazon to deliver the new ones. Thanks so much!

@danfixeseverything 8 месяцев назад

I love hearing stories like this. My friend had just paid $300.00 for this same repair a couple of months before I made the video. Let me know how it works out for you, and thanks for the story. Dan

@billybradford 8 месяцев назад

It's a happy ending! The new suspension rods arrived, I popped them in and our washer spins like a top! Thanks again, we appreciate you!

@danfixeseverything 8 месяцев назад

I LOVE hearing this. I am so happy this helped you.@@billybradford

@jennb4375 19 дней назад

Thanks so much for this video! I know it takes time and I really appreciate that! Because of you, I was able to fix my washer, by myself, and save a ton of money. My dad taught me how to be handy and my knowledge of tools. He passed away 12/13/2023 (He could work on and fix anything) so, unfortunately, I no longer have his guidance. Your video helped walk me through it. My washer is back to working like the first day I bought it! Thank you so much! Means the world to me 🙏❤️ *also... I believe the ones that say they did this repair and it worked for a while then stopped working again may be overloading their washer by trying to wash too big or too heavy of a load. But, I do recognize that they don't make things like they used to! It's been 4 mos since I repaired mine and it's still working fine.

@danfixeseverything 17 дней назад

I am so glad it helped you. Thanks for the comment.

@jimmartin7763 3 месяца назад

Dan’s the Man ! In the last year I have repaired microwave door and oven igniter; Samsung washer is next. Thanks for sharing Dan and kudos for the little story at the end.👍

@WormStomperTV 3 месяца назад

I like that story at the end. Thank God there are still some honest individuals with integrity walking the planet. This keeps me from fearing all the lunacy that dominates the internet. Great job, Dan!

@danfixeseverything 27 дней назад

Thank you.

@dianefaas7105 6 месяцев назад

Dan ,You were spot on , My husband ordered the rods like you recommended and got grease @ the hardware store. Our washer is now working I have been doing laundry for days. Thank you !

@danfixeseverything 6 месяцев назад

I am so happy to hear that. I repaired mine 7 months ago and it has not gone out of balance once. Thanks for letting me know.

@Mikey-vt3to 11 месяцев назад

Thank you so much for this video and your honesty. I was going to buy a new washer as we've had this one for about 9yrs and thought maybe it time for a new one. This is seems like a fairly simple fix and I am now going to attempt to do it myself instead of buying a new washer or calling a service tech out to the house. Thank you again, you are one of the good guys out there that I have absolute respect for. Take care and God Bless!

@danfixeseverything 11 месяцев назад

I had never done this repair before either. It is not very hard. Use a thin scraper blade to open the top from the front. Remove the screws from the back, and support the top. Drop me a note on how it comes out. Thanks for the comment. Dan

@jpettinicco 4 месяца назад

Literally the one impossible part of this repair is lifting the top up. Video starts with top off and my guy says "it just lifts right up". Smh.

@genarofan 9 месяцев назад

thank you Daniel,very kind of you,,.iam very glad thinking of there are honest people still existing on planet earth.i live in florida ,and you are in colorado.the Lord knows . God bless U. S. A.

@cumintothevoid 5 месяцев назад

dan is the man frfr, just handled this repair easily. thanks for the help brother!!!

@danfixeseverything 4 месяца назад

Happy to help. I am glad it worked for you.

@Iiinejcakes 8 месяцев назад

Thank you sir !!! You’re amazing 🥹 I bought my rods and doing this tonight . I will teach my 13 y/o son as well. Forgot to get my lithium grease but going to buy right now

@danfixeseverything 8 месяцев назад

That is great. I wish you great success!!!

@davidhume5852 10 месяцев назад

Just want to say Thanks. I have the very same machine with the very same problem which seems to be very common. I got the rods and amd replacing them tomorrow. And you mad it very easy. I'm also a DIY guy and the little things like white lithium was good. And your honesty refreshing. Aloha

@danfixeseverything 10 месяцев назад

Glad I could help

@lenacheney 5 месяцев назад

Did it work?

@davidhume5852 5 месяцев назад

@@lenacheney Yep, that's what the problem was. Got the rods on amazon. I guess they wear out after what I think is to short a time, Easy to install.

@mollyrichard8616 11 месяцев назад

OMG this is exactly the help we needed! Thank you!

@danfixeseverything 10 месяцев назад

It worked for me. I hope it works for you also. Let me know how it goes. Thanks, Dan

@sgmsos 5 месяцев назад

Thanks Dan, I stumbled across your video and although our washer is not a Samsung, the info you provided allowed my husband to fix our washer! thanks again!!

@danfixeseverything 4 месяца назад

Happy to help. I am glad it worked for you.

@sgmsos 4 месяца назад

@@danfixeseverything I just realized you prob couldn't recognize my name from my user Id... this is Susan M from Unity of the Palm Beaches :-)

@danfixeseverything 4 месяца назад

@@sgmsos Susan, that is great that I was able to help someone I know. The video has over 50,000 views. It seems to be a common problem. Please subscribe if you have not already. It's free and helps me. Dan

@darreno1450 Год назад

Great video, thank you. I'm going to order the parts to do this repair.

@danfixeseverything Год назад

Thank you. It is a great way to save money. Remember to tape the lid, and suspend the top carefully to protect the wires and hoses. Drop me a note when you finished. I would like to hear how you did. It has been a few months now and my washer has not been out of balance once. More videos are coming. Dan

@makaylaerin 11 месяцев назад

Very helpful! Thank you Dan! You’ve got a new subscriber!

@danfixeseverything 11 месяцев назад

Awesome, thank you!

@hypnosisbeats 7 месяцев назад

Thanks Dan

@bryantrobinson2481 3 месяца назад

Helped me a lot. Thank you sir!

@mightysprocket 2 месяца назад

I don't recommend using white lithium grease, I would get "dampening gel/grease" instead. It actually slows the movement of the rods and springs (its sticky), rather than lubricate them for ease of movement.

@danfixeseverything Месяц назад

Thanks for the advice.

@coolbeandean 2 месяца назад

Just an FYI. I purchased a Samsung washer at Lowes 3 years back and after about a year, it started this ballance issue. I saw this type of fix on RU-vid but opted to call a service tech. He suggested I "save my money for a new washer." I spent the money and ordered the tencion rods. It worked for about a month. I drug the thing out to the road.

@danfixeseverything Месяц назад

Sorry it did not work for you. Mine has been working for one year with no problems.

@philipboudreau3433 3 месяца назад

thanks alot we were going to buy a new washer i will try this very self explanery thank you

@hazelheartsrbd Месяц назад

Made the repair. Worked great...for a bit. Now im back to square one...

@danfixeseverything 27 дней назад

I am not sure. I replaced mine over a year ago and it still works perfectly. There is a nut at the bottom center of the tub (on the inside) under a cover. That nut can become loose and even break. It is accessed by removing the cover and it is reverse threaded so you turn it counter-clockwise to tighten it. I have not done the repair myself and do not know anything else.

@christinabivens7647 6 месяцев назад

I’ve been having this issue with my washer. I’m glad I came across this video because I’m going to try this before I throw it out the door. Needless to say this thing has been testing my patience

@danfixeseverything 6 месяцев назад

It has been 9 months since I repaired mine and it has not gone out of balance once. Before the repair it was unusable. Good luck, and please let me know how it works out for you. Dan

@lenacheney 5 месяцев назад

Did it work? I've never hated a washing machine as much as I hate our Samsung. It takes me hours just to do one load because it gets stuck on the spinning cycle 😊

@danfixeseverything 5 месяцев назад

@@lenacheney That probably means the washer at the bottom center of the tub has come loose or broken. Inside the washer at the bottom, there is a cover over a bolt that holds the tub to the mechanism below it. If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counterclockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@tripleh123ize 5 месяцев назад

Rods replace usually work but in my case after new rods the washer was getting unbalance on spin cycle and I found another video with solving issue of balance ring on top of drum and that fix my issue follow video on fixing balance ring it works i wish would find it sooner.. going crazy with drum banging every wash. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-iRry5mju_Xc.htmlsi=Qyb-tx9fHOMQxNMO

@drewk8797 20 дней назад

Thanks it helped me alot. God bless ya!

@nicolecott264 29 дней назад

I watched this video and i am SO happy to have seen this. However.. the rods from Amazon.. went out within 40 days 😭 back at square one again. So... a THOUSAND thumbs up to this guy and this video... lots of thumbs down to these amazon rods 😞 SPRING FOR THE EXPENSIVE RODS!!!

@danfixeseverything 27 дней назад

@vivianproff8255 11 месяцев назад

Very helpful. Thank you so much

@danfixeseverything 10 месяцев назад

I hope it helps. Let me know how it goes. Dan

@danfixeseverything 10 месяцев назад

I hope it helps. Let me know how it goes. Dan

@kearaoneil418 8 месяцев назад

You just saved me $450. Thank you!!!

@danfixeseverything 8 месяцев назад

I am so glad to hear it. That was the idea when I started this. Let's save money and use it for more fun stuff than paying a tech for stuff we can do ourselves.

@user-ct5bq2ru2s Месяц назад

Great video

@danfixeseverything Месяц назад

Thank you.

@Trujillo4u 6 месяцев назад

Honestly i cant say thank you enough

@danfixeseverything 6 месяцев назад

I am so glad to hear it helped you. Please subscribe, as there is more to come. Thanks for the comment, Dan.

@KristenShamblin Месяц назад

I did this. It worked!!! For a few weeks… now it’s unbalanced before it even puts water in?? I hate this washer.

@patti-anndresback1010 8 месяцев назад

Hello! Thanks for sharing! Questions does the order matter? I was thinking about replacing the one with the hose clip first since there will be less tension.

@danfixeseverything 8 месяцев назад

The order does not matter. Your idea sounds good.

@yourfactstory 6 месяцев назад

Hi , Dan, thanks for the video, you got new subscriber !! I change my rod and still out of balance. Any idea ?

@danfixeseverything 6 месяцев назад

Yes, inside the washer at the bottom there is a cover over a bolt that holds the tub to the mechanism below it If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counterclockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@dennisgt2008 8 месяцев назад

Can i use Superlube multi-purpose synthetic grease or do i have to et the lithium grease you stated in your video?

@danfixeseverything 8 месяцев назад

I am not familiar with Superlube but my guess is that it would work. These are wear points and need a lubricant that is long-lasting and works in a humid environment. Good luck with the job!

@icicicles Месяц назад

Next time remember that the weight/load compresses the spring so greasing up the rod is a messy waste of time and grease. Don't feel bad, most people follow that same pursuit, greasing the wrong direction.🤔😊😂 One last thing, remove the lid tape before locking the top down.

@renders_universe 9 месяцев назад

wait what washer model is this

@lmgardner8175 11 месяцев назад

Does it run normal if empty with this issue? I am having out of balance problems but repair man ran washer empty and it did fine. When I wash, it goes out of balance does same thing you describe. But they want a video before shipping. Would not take apart to check. I told them the rods were the problem.

@danfixeseverything 11 месяцев назад

Running an empty machine is not a good test. If it will not wash clothes it needs attention.

@chrispena1947 24 дня назад

Hello. So I just shad the rods replaced. And a week later we are back to an unbalanced load constantly. Any ideas

@danfixeseverything 24 дня назад

There is a large nut under the center of the agitator at the bottom of the tub. When the old suspension rods allow the tub to go out of balance and shake severely the nut can loosen or even break. You must remove the cover at the center of the agitator, then remove the screw holding the agitator on and remove the agitator. Then you will see the large nut. Use a wrench to tighten it. It is a left-hand thread so you must tighten it counterclockwise. If it is broken, replace it. Here are links to two videos I found that show how to fix it. I hope this helps you. Dan ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Yl-t1PVEBrc.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-d71a0BkWRA0.html 3

@SkylineMedia360 10 месяцев назад

I cant get the top to come off. Unscrewed screws in the back. But mine doesnt have those black clips on the front. Is this cause its a newer model? Ideas how else to remove the lid?

@danfixeseverything 10 месяцев назад

The clips are not visible. They are about six inches in from the sides on both sides. If you use a thin stiff putty knife you should be able to feel them. This was the hardest part of the job. To release them you have to push in on them while prying up on the top. You may find other videos that show the process better than my video. This was the first video I had ever done. I was happy because it saved me about $300.00. If you pry a little you may be able to see the clips with a flashlight. They are fairly stiff. I am not aware of any other method of holding the top on. I am handy but not a full time appliance repairman so I am not familiar with every brand. Best of luck to you.

@user-xp7lo5ti7x 9 месяцев назад

on of his videos told me about the screws under the black plugs

@user-xp7lo5ti7x 9 месяцев назад

screws under black plugs

@lauram8433 4 месяца назад

what do you do when you replace, one of the original suspension rods was clearly not up to standard, so all new fresh ones in, run it on spin and it has the same issue again where the water fills back up and it restarts the cycle? i was feeling so accomplished

@selan3529 Месяц назад

You might need a new control board. Many models give an out of balance error due to the board.

@germancantu9847 Месяц назад

I changed the suspension rods on mine and still having the same problem, any ideas on what else it could be? It does it even with small loads.

@joextreme Месяц назад

probably the spinner nut is loose

@davehorlacher 7 месяцев назад

If you have the samsung WA50R5400A / WA50T5300A, plan on replacing the springs once a year. But also clean the washer with Citric Acid as grime builds up and throws off the balance causing wear on the springs.

@danfixeseverything 7 месяцев назад

Thanks for the advice Dave. This is my first Samsung top-loader.

@ilive4anime. 2 месяца назад

Dan help!!! I replaced the suspension rods but the drum is much lower than with the original.

@danfixeseverything 27 дней назад

I am not sure. Are the rods the same length as the ones you removed?

@LonSchild 2 месяца назад

I've replaced the suspension rods. I had a short lived improvement, but now after aproximately 6 months I'm having continued problems. I saw somewhere that another fix may be available under continued occurances. Are you aware of any additional fixes?

@danfixeseverything 27 дней назад

@leewaynenishida8732 14 дней назад

If you used synthetic damping grease on the old rod you would have saved more money?

@user-to9od7es8w 7 месяцев назад

I'm having a hard time finding the part for my washer with the model number DC68-04090A-00 / WA50R5400AV- do you have any advice on what I should order? Thank you in advance.

@danfixeseverything 7 месяцев назад

I searched Amazon with just the WA50R5400AV number for suspension rods and this was the result I got. www.amazon.com/s?k=wa50r5400av%2Fus+suspension+rods&ref=nb_sb_noss There are several to choose from. Let me know how it works out for you. Thanks for watching. I hope you will consider subscribing too. Dan

@user-to9od7es8w 7 месяцев назад

Thank you. I have subscribed and got part. However this did not resolve my issue. Thank you so much for this video. @@danfixeseverything

@danfixeseverything 7 месяцев назад

@joextreme Месяц назад

@@danfixeseverything its a pain in the butt to get to that, my nut broke and replaced it with m28 size but i get to spin mode and it adds more time to add water, rods were put in months ago to repair the knocking noise. Will need to replace rods again and see other wise new washer, model WA48H7400AW/A2

@michaelstarrin2720 5 месяцев назад

I have a samsung wa484dshawr/a1 and i can't get the top off to replace the Suspension rods.

@danfixeseverything 5 месяцев назад

I don't know all the machines. Mine had clips about 6 inches in from either side on the front where the top sits. I used a stiff putty knife to push in on the clips while using another to lift the lid. This was after removing the screws on the back that hold the top on there. Some people have said they had screws at the front that had to be removed but I have not seen any like that. You might search for "how to remove top on Samsung washer". I found this video and it shows the removal at minute 1:12. www.google.com/search?q=Remove+top+from+Samsung+top+load+washer+wa484dshawr%2Fa1&sca_esv=8212b838d9203bd8&sxsrf=ACQVn0-mbxHLkhwVF9s66GkaQ-iiQgLQiw%3A1706640298956&source=hp&ei=qkO5ZZ-WOOfAkPIPxIuSyAk&iflsig=ANes7DEAAAAAZblRukvJqvMv7ppP38NkRu4eohtKMUu8&ved=0ahUKEwifk5vG4oWEAxVnIEQIHcSFBJkQ4dUDCB4&oq=Remove+top+from+Samsung+top+load+washer+wa484dshawr%2Fa1&gs_lp=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&sclient=gws-wiz#fpstate=ive&vld=cid:6b24b383,vid:LifEij0SMMU,st:0

@reyadsingh8802 4 месяца назад

Hi where can i get the part number to ensure I'm buying the right rods?

@danfixeseverything 27 дней назад

I got mine from Amazon.

@thewizard3140 Год назад

Timing is everything… Just recently I paid a service company $300 to do this exact repair. They did a good job and fixed my washer. But the reality is this - if you are handy around the house - and you are or you wouldn’t be watching “how to repair” videos - Dan shows you exactly how to do this repair for just the cost of the parts. Had I watched this video before I called the service company, I would have saved a LOT of money.

@danfixeseverything Год назад

Just for full disclosure, Kevin (the wizard) is a friend. When I shared my video with him he told me about just paying $300 for this repair. So the comment is from a friend, but the story is true. Sorry about the bad timing Kevin.

@EriBarr 9 месяцев назад

I like to watch random fix it videos and so far many have come in handy! I was being charged an insane amount to replace the belt on my drier.. I ended up doing the work myself and spent under $50.. it’s an old hand-me-down drier so I wasn’t too scared.. but my washer is the first pricey appliance I’ve bought.. but the insurance just went out so im going to try and do it myself.. wish me luck lol

@joextreme 7 месяцев назад

Just got done replacing my rods and ran a self clean, quiet as a whistle as it was knocking loudly prior. I didn't need a putty knife to pinch those two clips, i have a plastic prier and pried the top off as those two clips in front just snap on to cover. I forgot to unscrew the metal panel piece oh well, junky samsung washer, same as yours, ours is rusty in the bleach dispenser. Any idea how i replace the top piece? I was looking for a part but can't find anything on how to remove the existing one and replacing it. I don't want to replace the whole top with glass lid. Anywhoo, no more knocking and i think the washer had issues filling properly so will test a load of clothes after self clean. I had replaced the whole water inlet a few years ago. The back corner ones were a little tough as my washer is in a small closet so hard to get around haha.

@joextreme Месяц назад

update, same crap happening, in spin mode about 4 mins it adds 18 mins and does rinse again so the rods i had bought were junk, lasted a few months, also this time i took the inside plate off in drum to get to the Spinner nut, that was completly broken, replaced that, still same. One point it sounded like a machine gun. Will probably look for better quality rods and give it another shot . My model is a WA48H7400AW/A2 same as in video i believe. also the cover for the bleach area is no longer available and its rusting the metal a part.

@elizabethbinion1709 9 месяцев назад

we have this same problem so we replaced the rods. it is still doing the same thing do you know anything else we can try? thank you

@danfixeseverything 8 месяцев назад

Yes, inside the washer at the bottom there is a cover over a bolt that holds the tub to the mechanism below it If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counter clockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@lenacheney 5 месяцев назад

Did you fix it? I literally have anxiety doing laundry now because it's always out of balance

@ttvjxnsfn8154 Месяц назад

I installed new rods and it still shakes and throwing a code what else could it be

@stuartvernon107 28 дней назад

I replace the road but after about two weeks the washer is off balance again. Is there anything else I can do?

@danfixeseverything 27 дней назад

@corrineelgin7860 4 месяца назад

I followed this and it’s definitely firmer but its still shaking and setting the ur code off. Any other ideas on what to do now?

@danfixeseverything 4 месяца назад

Yes, inside the washer at the bottom there is a cover over a bolt that holds the tub to the mechanism below it If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counter clockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@Schmidty8806 6 месяцев назад

So what if we replaced the rods and balanced the washer and we are still getting violent shaking?

@danfixeseverything 6 месяцев назад

That probably means the washer at the bottom center of the tub has come loose or broken. Inside the washer at the bottom, there is a cover over a bolt that holds the tub to the mechanism below it. If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counterclockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@lauriemyoung42 4 месяца назад

I changed the suspension rods and it did not help my problem. Washer is level. I have washed small loads with just socks and shirts, I have washed sheets, blankets, every weight and water level, and I also checked the nut at the bottom of the tub. It's still off balance and codes with every wash. My daughter washed 2 quilts that were so so heavy once wet and I'm sure that's when my problems started. Any suggestions?

@92Millie 3 месяца назад

I have the same issue I just replaced them and still does the same thing. Did you find an answer yet?? I’m DESPERATE 🫨

@joextreme Месяц назад

try this hack turn washer off, hold down spin and soil button and power on and switch knob to spin and it will spin but be careful i think that is what broke my spinner nut.

@garybarnes3091 Месяц назад

My suggestion is don’t buy a Samsung again. I changed out the rods and balancing ring. Only helped for a short time. I replaced the POS Samsung with a Whirpool. Had enough

@joextreme Месяц назад

@@garybarnes3091 ya looking to do the same.

@crickettblount 7 месяцев назад

Where is the counter weight on the samsung top load washer

@garryweber4199 6 месяцев назад

I did the repair. Was way simpler than I thought it would be. BUT went to do a load of laundry and it kept filling 😮. I emptied it and drained it, did a calibration but it’s still filling until I turn it off. Any thoughts ?

@danfixeseverything 6 месяцев назад

In Google or RU-vid search for "samsung top load washer keeps filling with water." It may be low water pressure. If you turned your water off, make sure you turn it back on fully and that the hose is not kinked. There are sensors that go bad also that are addressed by other RU-vid videos. Good luck.

@garryweber4199 6 месяцев назад

Thanks for the advice. It turns out the hose popped off the water pressure/level sensor when I lifted the top of the washer off. Just had to pop it back on

@danfixeseverything 6 месяцев назад

@@garryweber4199 thanks for letting us know. It might help someone else.

@peppersweeney9493 5 месяцев назад

I followed the instructions to a T. At least I thought I did! The tub is now too high and making contact with the top of it he washer. Help!

@danfixeseverything 5 месяцев назад

Yes, inside the washer at the bottom there is a cover over a bolt that holds the tub to the mechanism below it If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reversed threaded so you would go counter clockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@user-xp7lo5ti7x 9 месяцев назад

have an active jet on my washer and kept looking for the clips, this guy told me to remove rubber plugs and unscrew DDDDUUUUUmmmy

@rsmolkin 9 месяцев назад

Could it just be out of balance somehow?

@danfixeseverything 8 месяцев назад

There are two things I know of that cause it to be out of balance with even a small load of evenly distributed clothing. The most common is the suspension rods that I show how to repair in this video. The other is a broken or loose nut at the bottom of the tub. It is accessed from the top. It often happens as a result of weak suspension rods causing violent out-of-balance problems. If replacing the rods does not solve the problem then the cover at the bottom center of the tub needs to be removed and the nut needs to be tightened or replaced. I have not done this repair, as replacing the rods solved my problem. I believe the nut is a left hand thread, so turn it the opposite direction to tighten (counter-clockwise).

@kJ-hx8pm Год назад

What if I replace the rods but it keeps doing the same thing

@danfixeseverything Год назад

Did that happen to you? I replaced mine and it has worked perfectly so far. It has been about two months. When I had the problem I watched several RU-vid videos and they all agreed that the suspension rods were the solution. Washing machines are complex devices and of course, there is the possibility that there is a different problem. This problem and solution are very common. I hope it works out for you too. Dan

@user-qg2ve1ig7v Год назад

I have the same issue. I replaced my rods but it’s still unbalanced. I can’t find anything online to help me figure it out. I’m thinking maybe the bearings are bad and that’s causing it?? I for sure needed to replace the rods but now I am at my wits end with this machine. It’s only 2.5 years old too……

@danfixeseverything Год назад

@@user-qg2ve1ig7v There is a large nut under the center of the agitator at the bottom of the tub. When the old suspension rods allow the tub to go out of balance and shake severely the nut can loosen or even break. You must remove the cover at the center of the agitator, then remove the screw holding the agitator on and remove the agitator. Then you will see the large nut. Use a wrench to tighten it. It is a left-hand thread so you must tighten it counterclockwise. If it is broken, replace it. Here are links to two videos I found that show how to fix it. I hope this helps you. Dan ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Yl-t1PVEBrc.html ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-d71a0BkWRA0.html

@danfixeseverything Год назад

@danfixeseverything 11 месяцев назад

@roywood9683 2 месяца назад

too much grease on plastic stress points. also use synthetic dampening grease on rods near springs this makes slide more sticky helping to dampen rod movement.

@robertjavior4339 10 месяцев назад

The right front rod wasn't seated in the plastic top piece 90 degrees off.

@danfixeseverything 8 месяцев назад

I am happy that you were able to repair it. Dan

@rayray8840 3 месяца назад

Similar story here as a plumber, work for a big company for a few weeks. The owners made the employees upcharge everyone, crazy B.S.

@kiml7700 9 месяцев назад

Darn Top doesn't come off..... Even with a putty knife

@danfixeseverything 9 месяцев назад

That was the hardest part of the job. I used a stiff strong putty knife, along with a thinner one to lift the lift lid slightly. I used a screw driver once I had the room. The clips can be stiff.

@rigodiaz89 9 месяцев назад

Your specific top might have screws that are holding it down.

@selan3529 Месяц назад

A ton of samsung models will also give an error due to a faulty control board. Samsung is notorious for having bad electrical problems with their appliances. I would not recommend just buying an expensive control board. Might be better to replace at that point.

@danfixeseverything Месяц назад

Thanks for the information.

@user-td4gz2eq3s 6 месяцев назад

Replaced rods still doing the same out of control spin

@danfixeseverything 6 месяцев назад

Inside the washer at the bottom there is a cover over a bolt that holds the tub to the mechanism below it If you remove the cover there is a large nut that secures the tub. The action of the tub swinging so far out of balance due to the bad rods may have loosened or broken the nut. I believe it is reverse threaded so you would go counter clockwise to tighten it. Please let me know your results. I hope that works. I saw it on another channel's video.

@lenacheney 5 месяцев назад

Ever figure it out?

@danfixeseverything 5 месяцев назад

@armenz.6601 29 дней назад

Hey who's going to pay for all the water this has been wasting. I have a large tub and it's been doing this for months. Here in California we just had a drought. 😅

@lmgardner8175 11 месяцев назад

Repair man said zI am either under loading or undercoating and nothingbis wrong....

@danfixeseverything 11 месяцев назад

Try running a normal load, about half full with no very heavy items like rugs, etc. If the machine cannot finish the complete wash cycle without going off balance it does not seem it is an underloading or overloading problem. I hope this helps. Dan

@user-bk4uq8yl4j 6 месяцев назад

He doesn’t show you how to open the washer up,

@FLManDan 4 месяца назад

Why does every video skip how to take the top off lol

@amykhiry873 9 месяцев назад

Great video！！！Sorry for my offense， would you be interested in filming a new repair video? I'm an Amazon seller and would like to send you a set of Samsung Suspension Rods which will fit your washer. In addition, we will also provide a video sponsorship fee of 50 US dollars as a thank you. We look forward to your reply.

@danfixeseverything 8 месяцев назад

Sorry for the slow reply. I was travelling and just returned home. Yes, I am interested in your offer. This was my first video and I think I can make one even better. Please send a link to your product and I expect to be able to accept your offer and produce the video. Dan

@amykhiry873 8 месяцев назад

@@danfixeseverything THANK YOU FOR YOUR REPLY！ How can I contact you? Would you mind telling me you mail?

@danfixeseverything 8 месяцев назад

My email is danbarnettphoto@msn.com@@amykhiry873