Error code AE6 = communication problem between inverter board and user interface board, check all the wires and connections, if didn't find any problem, replace main board located at the back 😀 www.facebook.c...
Thank you for showing the model number of your washer! Too many RU-vid videos don't tell what model washer they are working on, and I find that the instructions for getting Samsung Washers into Diagnostic Mode are NOT all the same; there's quite a variety of procedures, depending on the model.
There is a new diagnostic mode on Samsung washers Step 1: open the washer Step 2: put the hours to 17h (hour's) Step 3: start it Step 4: hold the start button until its on diagnostic mode Step 5: you are now done
Hi there I have a KitchenAid dishwasher model number KCPw354gps0 that appears to be flashing it looks like a battery light what does that mean and how do I fix it?
A36 is actually AE6 which is communication error code between 3 control board which does not make any sense , JOOF is software version or has something to do with circuit print has nothing to do with washer itself . It’s auxiliary note .
Hi Hameed!We have samsung 4.2 cubic feet front load and every time when every spin cycle starts, the washing machine begins to shake and walk about 3-5 seconds and then stops and starts to rotate normally.Any ideas
Vesel Vasilev make sure the fees are properly installed to the ground and it's balanced, straight to the ground, otherwise check the shocks inside the washer, make sure those are not broken or has crack on them, check the spring that holds the drum to the cabinet,
Could be unlevel there are feet u can twist to lower or higher to level out also could be bad suspension rods or tub balance ring. Or just a unbalanced load readjust clothing
Spin your drum with hand first to see if it’s spins freely. If it’s spinning freely you probably got a broken wire at the back on the motor or rom sensor is defective . It’s most likely seized motor which is caused by broken bearing, on Samsung it’s very common .
Thank you i have the same washer it will stay stuck in spin cycle. And turn off and turn back on on minute 33 and go back to minute 37 you think is the same problem?
adrian mendoza open the back panel holded by 2 Philips screw, check the motor rpm sensor, that's probably loose, or defective, you problem looks sensor not board, a broken shock would also do that, sometimes it sticks in 9 minutes won't do anything but keeps spinning and slowing down,
adrian mendoza I am getting the AE6 error. The washer will freeze after a couple of minutes of use. Can you show what you did in the back of the washer to fix it or give me a quick idea on what to look for? Thanks
@@hameedwafaAFG is there any other way to diagnose it? I was getting the 5C code and I wanted to check the pump, but I am not sure how to do it without leaving my washer in nothing but a scrap heap.
@@dompennypacker4491 5c code is usually water valve error code . Make sure water is fully on . Make sure it’s not making buzzing noise and filling low water . Or maybe it’s not working . Open the water lines and check the water valve screens for calcium rust or other minerals ✌️
@@hameedwafaAFG it was fully on. It was not draining the water, which it would stop when it was time to switch to rinse and or spin cycles. As a matter of fact, the pump was no engaging at all.
elyas abdel you need to replace the ui and main control. Very Expensive repair that most people will junk it and buy another washer that’s not Samsung or lg. Speed queen is the champion, least they were. I don’t know about the new model though.
I’m getting an 8E1 error code. However I replaced the vibration sensor and I’m still getting an 8E1 error code. I’m about to lose my mind!!! It’s been down for 5 months now. 🥴😵💫🤦🏻♀️ 🤯🤬😭 I replace the bearings and seal, the spider arm is in great condition I replaced the shocks, and now I’m getting the 8E1 error code. Please if anyone can help I would be so grateful! 😊 Thank you Samsung Wf56H9100ag/a2-00