THANKS FOR THE VID although i get a upside down f and c1 when i get the code from it. New board? cant get it to spin at all. water fills on 2 seconds off 2 seconds timer does not move and shuts ddown eventually. Any ideas if its not the main pcb?
Hi Thank you for reaching out. We appreciate your feedback on the video. Based on the error codes "Upside Down F and C1" that you are receiving, it appears to be related to a communication error or a malfunction in the main control board. However, it's essential to consider other possible causes before concluding that it is the main PCB. Here are a few troubleshooting steps you can try: 1. Check for any loose connections: Ensure that all the electrical connections to the control board are secure. Loose connections can sometimes cause communication errors. 2. Inspect the wiring harness: Carefully examine the wiring harness connecting the various components of the washer. Look for any signs of damage, fraying, or loose connections. Repair or replace any faulty wiring as necessary. 3. Test other components: While the symptoms you described point towards a potential issue with the main control board, it's worth examining other components as well. For instance, a faulty motor or a malfunctioning timer can also prevent the washer from spinning properly. If after performing these steps, the issue persists, it is advisable to consult a professional technician. They can perform a more comprehensive diagnosis using specialized tools and experience.
Hi, i think you are referring to the motor control board. I recommend locating your exact model number and use sites like www.searspartsdirect.com/ to find to correct parts for your unit. With Samsung you will also need the revision code as well found on the label.
Hello there My machine is having 110 volts on one of the solenoids contact and it stays open at one point. What should I replace ! Power supply or the other side!
Hi, if the solenoid is getting 120 volts then it will stay open, sounds like could be stuck relay on power supply. I would need more specific on the unit and issue. Thanks
when I do the spin test, it shows 1300 and doesn't change. is that okay or should it show the speed changes? I am having a similar issue of intermittent completion of the wash cycle failing with wet cloths left in the tub sometimes. Larger loads fail for sure, lighter loads pass. When I say larger loads, two towels can fail. even sometimes the smaller loads fail. they stop at a certain time left and I press play and it will finish. Any suggestions? samsung wf45h6300ag/a2
@@RepairProTrepreneur i get the 3e2 error when i do the spin test. The machine runs but sometimes doesn't finish spin cycle and leaves wet clothes. I can press start again and it will finish. No error codes on the display , only when I run the test mode. I think its the inverter from everything I read. i am going to multimeter it this morning
@@RepairProTrepreneur funny, i did a multimeter test on the inverter board. I did get some ohm readings that were not consistent with the test sheets numbers. The stator tested fine. i removed the board, and stripped off the coating to inspect. it all seemed fine. put it back into the box and machine and it is working great. maybe there is a lose connection in the wire harness? I have an ESR and new Multi meter coming and if it acts up again, I will further test
Hi there, I have the same washing machine, it goes ON and OFF many times in all the washing cycles, the display also goes OFF and I can hear the relay (the same than I hear when I plug the washer), do it many times, goes OFF and everything comes back On 1 second or less later, the cycle restart, no error codes or other information given. Have an idea of what can causes it? Thanks for your help.
Hi there, I have same washer however it resets the time to a higher time when it is about to finish the spin cycle and keep doing this forever. I don't hear any sound related to broken piece. Can you suggest if it could be main PCB board or Invertor Board which you replaced in the video. Any advice?
Hi it could be the inverter control board, you should take a look at the error codes to make sure you don't have a long drain error which will cause the as well. Hope this helps
Hi, AC6 error is an error when the exchange of data between the control module and the information display board has an issue. Recommended Troubleshooting Tip: Switch off the washing machine and unplug the power cable from the power source and power it on again and start another washing cycle. If that does not work you may have to replace the control board
With a 3E or 3C error message, the motor doesn't work. First check whether the socket works. Switch off your washing machine and remove the connector. Check the water supply hose. Any leak in the hose can cause the water to flow out into the machine next to the back panel, so check the connection of the water supply hose to the tap and machine. ... Check for laundry caught in the machine. ... Check the door seal. Contact an Authorized Service Center.
This is one great video! I have a 3C error code, I took it apart just like you did, checked all my connections. It will reach the skin cycle at times and then stop. What you think it is top tech?