Security Light Installation Part 9: Setting Dusk to Dawn Light Control on 2N1 Area PIR

Подписаться 1,2 тыс.

Просмотров 72 тыс.

50% 1

This 240-degree PIR (passive infrared) sensor detects motion outward as far as 100 feet and motion below the fixture up to 15 feet. This PIR has two types of control settings: area light and security light. The area light setting gives out a low beam light during dusk to dawn and the security light setting feature gives out a high beam light when motion is detected.
goodearthlighting.com/browse-...

Опубликовано:

7 июл 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 25

@joemc111 2 года назад

15 million videos on RU-vid and you think I could find your last video.LOL.

@Rdavis6593 2 года назад

Good explanation of controls. Thanks.

@carbonite1983 4 года назад

Thank you for this video! I couldn't figure out the settings on the dusk to dawn dial. It is all clear now. This is a great light fixture.

@GoodEarthLighting 4 года назад

I'm glad this is helpful

@johnoceanyang5522 2 года назад

Thank you Those are make me goes crazy to set it up until I watch your video 👍

@cmspnutty8001 Год назад

We have 2 of these and have had them for about 6yrs now. They are beasts! Wicked bright, it has awesome motion sensing from far away and both left and right sides. The bulbs are still super bright. I am getting one more If they still sell them. To replace a crappy solar-powered one that we cringe at every night when it does not go on powered with the winter sun.

@GoodEarthLighting Год назад

These are still sold. Thanks for the review! goodearthlighting.com/240-degree-2500-lumen-dual-detection-led-motion-activated-flood-light-with-timer-white.html

@joecrabtree9335 4 года назад

THANK You for your great detailed information,absolutely,a big help to me seeing it+having it explained,thanks a lot,joe Cumbria uk

@recabitejehonadab2654 4 года назад

Do you always have to have the unit in test mode to reset? Or is it possible to have the unit set on 5 min for example then reset the unit at the switch and the unit will automatically work in the 5 min setting since that is what you have it set on. Or do you always have to start in test mode first then adjust your minutes.

@kimclark2536 4 года назад

My new light no longer comes on. The red sensor lights activate when I walk across the area but the lights will not come on. Currently, I have it set to Dusk to Dawn. Is there anything I can do to restore it and make it work again without having to buy a new one?

@brentoaks3628 2 года назад

Who makes this motion light fixture? What is the model#? I would like to buy one. It's exactly what I've been looking for and have not been able to find one.

@GoodEarthLighting 2 года назад

This is Good Earth Lighting. Model #SE1084-WH3-02LF0-G (white, two head), SE1084-BP2-02LF0-G (bronze, two head), SE1095-WH3-02LF0-G (white, three head), or SE1095-BP2-02LF0-G (bronze, three head). goodearthlighting.com/browse-products/by-category/outdoor-and-security-lighting/security-lights.html

@terrigunnoe8107 11 месяцев назад

I know this is an older video but maybe someone can help. We just purchased the IP65 model and have been trying to disable the sensor light to have this light only act as a motion/security light. We have our dial turned to "off" but it doesn't seem to want to shut off, it still goes to "dim" mode after the time period of the security light feature runs its course. Hoping someone can advise. Thanks

@GoodEarthLighting 11 месяцев назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-qyAzrZZKjdU.html Reset: While power/switch is on change the area light setting to 3 hours, then change the minutes dial to test mode. Turn power/switch off for 2-3 minutes. Turn power/switch on. Lights should come on for 15-20 seconds then shut off. After the lights shut off, try triggering in test. If they do not trigger that is fine. Take the fixtures out of test mode and put in your desired settings. Turn the area light off. Or to desired setting.

@DJSephEntertainment 7 месяцев назад

Mine started to stobe and the motion sensor began flashing red. I tried the reset procedure without success. Is my light hopeless?

@GoodEarthLighting 7 месяцев назад

Please reach out to customer service at 1-800-291-8838 for assistance. We are available Monday through Friday 8:30 am to 5:00 pm CDT. Or contact us VIA our website. goodearthlighting.com/contact-us

@kimberlyjohnson4232 Год назад

My PIR is flashing red. I have reset it but it is still doing it. Do you know how to fix it?

@GoodEarthLighting Год назад

Please reach out to customer service at 1-800-291-8838 for technical support. We are available Monday through Friday 8:30 am to 5:00 pm CDT.

@deweyferguson3295 2 года назад

My new installation (motion) cuts on and off every 30 seconds

@GoodEarthLighting 2 года назад

Please try resetting your fixture. If you still experience issues post reset reach out to customer service at 1-800-291-8838. We are available Monday through Friday 8:30 am to 5:00 pm CST. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-fW1MlKLKHlo.html

@markxenakis5249 3 года назад

@sergiocedeno6488 2 года назад

Don’t buy it mine won’t turn off

@GoodEarthLighting 2 года назад

Please reach out to customer service at 1-800-291-8838 for technical support and/or warranty replacement. We are available Monday through Friday 8:30 am to 5:00 pm CDT.