Serger Seized - Tracking down and Fixing. Bernina Overlocker / Serger

Подписаться 26 тыс.

Просмотров 3,4 тыс.

50% 1

This Bernina serger 1300MDC is seized tight and I show how to efficiently track down the seizure.
Once tracked down, I can then work at freeing up the seized part.
The procedures shown in this video can be applied to tracking down seizures in any serger / overlocker.
It also shows the importance of lubricating your machine and getting it professionally serviced from time to time.
Other videos showing tracking down seizing parts...
1948 Singer 201K - Tight Spot - Showing Fix - • 1948 Singer 201K - Tig...
A Happy Outcome for the Seized Bernina 117L - • A Happy Outcome for th...
Details of subjects covered can be found in the index below.
Please consider supporting the channel at Patreon - / sewingmachines
Web Site - www.institches.co.nz
Index:
0:00 - Introduction
1:22 - Tracking down the seized part
6:43 - Applying a little heat to the seized part to try to free it
9:00 - Time to remove some parts
14:55 - Freeing up the seized part
16:25 - Assembling the upper looper shaft and pivot
20:26 - Checking machine by turning it over
20:44 - Conclusion and thanks

Хобби

Опубликовано:

5 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 12

@debbiehall4155 Год назад

Your camera angles and picture clarity are amazing and so helpful.

@sherrillsturm7240 4 дня назад

Update: I cannot get my Juki repired on-island it seems. So, I watched this video again and found my problem is the same you found, the looper shaft seized. I've now tried some penetrating oil, and will be paying attention to that for a while. Thanks millions.

@sandoresmint1186 5 месяцев назад

Hi, thank you for your video. My co-worker's serger seized. The repair guy said that there was a 1 month waiting list, the other option was 4 hours drive and probably forking out a fortune. Your video helped to trace down and fix the problem within minutes. 😀

@sherrillsturm7240 5 месяцев назад

Really hoping I can get my serger to free up after watching this. Great video and clear process shown. Otherwise, I might have to ship it overseas to get a repair, a prospect that I dread.

@jeanettewithrow9641 Год назад

Boy there's not much room for you to work. You do amazing figuring all that out

@pamelaleavers2860 Год назад

Hi, thanks for the great video and the notes about oiling. How do you adjust the clearance between the upper looper and lower looper? I got a cheap 2nd hand one but the upper and lower loopers hit each other stopping them form going forward. Thanks

@sherrillsturm7240 5 месяцев назад

I DON'T KNOW WHICH BRAND YOU HAVE, BUT ON THE ASSUMPTION THEY ARE SIMLAR, THERE IS A SET SCREW ON EACH LOOPER SHAFT THAT CAN BE LOOSENED TO ALLOW YOU TO SWING THE LOOPERS BACK INTO POSITION. ONE OF THEM IS PROBABLY AIMED EITHER TOO FORWARD OR BACKWARD AND THE VERY SMALL ALLOWANCE TO PASS IS CLOSED.

@Jj-zy4xe 11 месяцев назад

Ok, can you use serger thread on a domestic sewing machine? Will it destroy the machine?

@IAMJEFFREY-cw9ns Год назад

Can you please do a video on how to assemble/set up a Zoje A6000-G/02 sewing machine? Or provide a link to such a video?

@InStitches Год назад

Hi. Sorry I don't have one of those and I'm not sure if there is a video for that. Thanks.

@IAMJEFFREY-cw9ns Год назад

@@InStitches Alright mate👍

@JohnJohn-zn8ib 5 месяцев назад

Hi, I tried to fix a cheap Aldi overlocker called a Stirling, the owner hadn’t used it for a year and hasn’t used it much at all, it was seized but I got it to free up, unfortunately the needle bar finds it hard to pierce fabric and goes out of time, it just doesn’t have any piercing power, because it is a cheap brand, I advised to get a branded model, it will probably cost a bit more but the quality will be so much better, have you had a similar experience, sorry I have forgotten your name, regards David.