Servicing D5/D10 electric gate opener?

Подписаться 425

Просмотров 29 тыс.

50% 1

#D5#disassembly #hackopen/D10slider#expresss#gateopener.Opening a #centurion machine #D5 for the sole goal of showing technicians and gate lovers the components that make up a gate opener

Опубликовано:

26 сен 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 45

@mosesyika1771 6 дней назад

I'm proud of you, keep up the good videos

@johanreyneke5837 Год назад

Very informative. Thank you for the post.

@preshnaidoo1043 4 года назад

Thanks, was just what I was looking for

@manyanyato 3 года назад

Dude...the lighting

@stephenwebb3069 10 месяцев назад

Thank you this was very very helpful

@jacowentzel723 4 года назад

Thanks. Good video 👍

@mirriamkubangu1396 5 лет назад

Thank you

@welcomegauche6870 2 года назад

Thank you so much🤓

@ashleynkoe2687 2 года назад

thanks for the video, my manual release wont release the gear what could be the problem

@fuzzs8970 2 года назад

Thank you. What needs to be done to replace the seals if there's a gearbox oil leak

@MayurHarkison Год назад

i also want to knwo which seals to replace if oil is coming with the counting disc

@nishahammond7185 Год назад

How to replace seals? Not enough light for video.

@siphamandlabuthelezi3219 2 года назад

My gate motor has an error saying gate installed then when moving its stops then say gate motor faulty what could be the problem

@nathanieldelouw2582 2 года назад

Sounds like you explaining my marriage, great job, how do I get in touch with you?

@jonathangeorge7417 3 года назад

lighting was poor in the video. wasnt able to see properly

@siyabongamdlalose4475 Год назад

Please assist I damaged the threads of the key for changing the motor from manual to auto

@chastomes7154 3 года назад

How do remove the the doss wheel

@fuzetechfuzetech5854 4 года назад

My gate is written setup limits and upon settings it runs and restarts itself like power off and on. What could be the reason?

@expressautomationstechmast7029 4 года назад

Battery could be faulty

@casperniemand 4 года назад

How do you remove the dos wheel in order to replace the oil seal behind the dos wheel? Thanks in advance

@expressautomationstechmast7029 4 года назад

Unscrew the four screw holding the lead , that is , after removing the sprocket

@silumesiisitwala4238 4 года назад

@@expressautomationstechmast7029 I have an error "gate motor failure". How do I rectify it?

@expressautomationstechmast7029 4 года назад

The motor might be faulty or the dose sensor faulty/not in place.

@yashgupta1633 7 месяцев назад

Sir, what to do if the motor shows no limit set, no origin found, max collision. Kindly give the solution separately. Thank you

@expressautomationstechmast7029 5 лет назад

Get to know what's inside a #D5 EVO Slider machine!

@gideonadjei4130 4 года назад

What is the cause for a D5 motor to open and cannot be able to close after putting it on manual still you cannot close the gate

@expressautomationstechmast7029 4 года назад

@@gideonadjei4130 When the gate is in auto mode, make sure all safety beams loop are in place.When the gate is manual mode, First make sure you have manualised the gate by turning the round wheel in the direction shown on wheel. If gate doesn't move in manual mode then you will have to open the D5 and service the gear releasing mechanism

@gideonadjei4130 4 года назад

@@expressautomationstechmast7029 Okay sir, thank you for the information

@chrishabib5325 4 года назад

This video was really helpful. How can I contact you, I have something to discuss with you

@expressautomationstechmast7029 4 года назад

Send an email : africantraditions1000ad@gmail.com

@octamy-qn8hl Год назад

how can you work in the dark? install & put some lamp light on then i will subscribe

@marcoclarke1436 3 года назад

can you show how to replace the bearings of the same motor

@jay_Mus 2 года назад

how can we contact you

@cyrilpercimoney7611 3 года назад

How do you top up the oil? Is it through the dipstick pipe?

@expressautomationstechmast7029 3 года назад

Yes! Oil top up seldom happens,unless there is a leakage in the machine!

@cyrilpercimoney7611 3 года назад

Thanks!!

@charleschimfwembe5528 2 года назад

@@expressautomationstechmast7029 and how do you replace a leaking seal?

@josephmarongo6358 6 месяцев назад

Next service please make sure of circlip pliers to remove the circlip. Not professional.

@greyalien6309 Год назад

You should buy and use the correct tools to show people the correct way to do things. A pliers is not a hammer, and a screwdriver is not a circlip pliers. You are a bush mechanic.