Setting up ESPHome for Home Assistant - ESP32 SMART Home Made EASY!

Подписаться 22 тыс.

Просмотров 26 тыс.

50% 1

A simple step-by-step guide to Setting up ESPHome for Home Assistant. This simple guide will explain how ESP home works, how to set it up and how to turn an ESP32 into a smart device capable of controlling any number of devices for your smart home.
A few videos back I promised to make a tutorial on the setup of ESPHome. This is the step by step guide that explain how to go from start to finish connecting an ESP32 to your smart home control center.
If you want to follow along, these are the tools I used in the walk though:
1. ESPHome: esphome.io/index.html
2. Home Assistant: www.home-assistant.io/
3. ESP32: geni.us/LB99
4. LED light (with resistor): geni.us/vxfV
5. Jumper wires: geni.us/MkogSjk
6. Breadboard: geni.us/AdB0cA
7. USB cable: geni.us/mwgY
Links mentioned in this video:
My configuration for containerized ESPHome: gist.github.com/gmorse81/7e23...
Container used for running ESPHome: github.com/esphome/esphome/pk...
Home Assistant installation instructions: www.home-assistant.io/install...
ESPHome Add-on page: esphome.io/guides/getting_sta...
00:00 - Intro
00:16 - Requirements - What you need
00:37 - The two components of ESPHome
00:48 - Two ways to install ESPHome
00:58 - The container install method
01:21 - The Add-on Installation method
01:44 - Adding ESPHome to an ESP32
03:26 - Fixing a ESPHome device showing offline
04:05 - Configuring your ESP32 with ESPHome
04:31 - Adding your ESPHome device to Home Assistant

Опубликовано:

27 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@keerthichinnaraju 4 месяца назад

My comment isn't about ESPHome, but just huge applaud and appreciation towards your content creation, your work, also the way you make the viewers understand the topic. You are absolutely brilliant, thanks a million much love and respect.

@manukalias 3 месяца назад

That was Straight forward and simple. 👍🏻👍🏻🙏🙏

@dracony0387 15 дней назад

thx for ur help

@alessandrovarini3424 Месяц назад

Everyone has to watch this video before venturing in ESPHOME world!👏

@AdeAiman 6 месяцев назад

hey can you make new like vr controller using esp8266 but with full finger tracking

@henrusyt Месяц назад

After i disconnect from usb, i can't upload again over wifi. Ip is already manually configured. Congrats on the video, very well explained!!

@LearnFastMakeThings Месяц назад

Hey! thanks! You might need to manually set the IP address in the config. after setting it manually, upload with USB one last time then try wireless again.

@henrusyt Месяц назад

Already done that, the device comes online much faster, but the update is not working. Everything seems ok in the logging, but the display won't show content.

@ashdt3779 3 месяца назад

How did you get homeassistant Store to work in container? I use docker and STORE is missing

@LearnFastMakeThings 3 месяца назад

Are you referring to HACS? No I didn’t. Any type of add on is essentially DIY on the container version. Mainly because the add ons themselves are also containers and the home assistant OS will orchestrate the containers for you.

@donkeydonkey Месяц назад

Anytime I try to install firmware from HA, HA crashes. Using a Pi 4B w/1g ram and 2g swap on a SSD. Any idea?

@LearnFastMakeThings Месяц назад

That might not be enough ram. You can, however, compile the firmware then install it from the esphome site.

@makeyourdr3ams 2 месяца назад

make a vid using container

@LearnFastMakeThings Месяц назад

@tgsparkyoriginal 2 месяца назад

I don't know how to get my HA to load as HTTPS

@LearnFastMakeThings 2 месяца назад

Don’t feel too bad, it’s actually way harder than it should be. The best way is to add a service to ha that will act as a https termination point and proxy the requests.