Nice work. allways so clean and effortless. One suggestion: try loosening all the bearing block bolts and then tighten them again by hand, skipping around like you would with a tire. Snug, firm, tight. I think she will ride a lot smoother
Otro magnífico proyecto , muy bien desarrollado y mejor ejecutado , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón , Galicia ( España) 🤓 😜
Amazing J. I really feel like you may invent something that changes the way many wood workers do this hobby and trade. Great video as well...as always.
Very nice jig, well done! If you plan to make that jig, add locktite to your material list. Use it on all setscrews and bolts. The last thing you want is a flying piece of hardware :)
Без сомнения прикольно смотреть как работают другие, но снова не до конца понятно применение. Минутной демонстрации деформации какого либо малоценного бруска было бы достаточно. Наверное в следующих видео автор покажет, посмотрю.
На последних секундах есть надпись: " Я покажу , как это использовать в следующих видео. Следите за обновлениями ". There is subscription at the last seconds of the video: "I'm showing how to use and application (?? mabe = apply or install ? ) in the next video. Please stay tuned".
As always very entertaining and professional approach but I don’t see the advantage over what you had before? It does the same task but only in a different way.
2:13 - Try drilling the large hole FIRST, you then have a center point to drill the smaller hole. Takes the guesswork out of finding center. Otherwise interesting project.
I'm curious what its runout would read from one end to the other, with a dial indicator ? I think your on to something... Good Job. You've earned yourself a new subscriber !
@Chooper @victor hopper As J-Woodworking says, he measured the distance between the parallel rails. If the error in this is low, the distance of each rail from the plywood to which they are fixed should be the same along the length of the rails, within the tolerances of the plywood thickness, the diameter of the rails and the rail mounting fixtures. Since the device is attached to the tablesaw fence, the only additional errors would arise from the standard errors between fence, blade and table, which I expect to be low.
@@jason4547 I know that you asked about the measured deflection from end to end. My explanation describes how the measured deflection end to end should be no (or little) more than that of the table, fence and blade without the additional sliding fence. If the plywood used for the sliding fence is the same thickness at each end; and the rod mounting pillars are identical within or better than the tolerances of the table and existing fence; and assuming the roundness of the rods is better than these tolerances; because the rods are parallel the error end to end will be within the error end to end of the originally fitted fence from the blade. I believe that measurement of the end to end variation for the fence and blade compared with the sliding fence would bear this out. I hope you get it. Sorry I can't explain it any clearer.
조기대는 일본말이예요. 영어의 가이드라는 의미인데, '행정 용어 순화 편람'에서 제시하는 규준대, 미장나무자는 본래 용도에 그 의미가 부합되지 않는다고 생각됩니다. '정확하게 가공할 수 있도록 도와주는 가이드'라는 의미를 순우리말로 뭐라 부를까 고민해 봤는데요. 그므개와 '길잡이'를 조합한 '금잡이'가 제가 제시할 수 있는 한계입니다. 그므개는 아마 금(긋는) 물건이라는 의미일 것 같아서 이렇게 생각해 봤습니다.
I see most of the comments on here say that's a good idea. I'm wondering if you have made some wooden wheels for your car too because that would be as useful as this idea.
молодец. руки есть. вопрос. нах у я .? (ипать я тоже люблю приблуды мастырить..) ок. fine/ but what reason//how use it// va bene //ma сhe lavoro sorry for my esperanto
Before I made it I anticipated that. This fence is concept one. There will be problems. And I keep solving them. Through the process I'll make progress. Sorry sir.
![sliding fence for better table saw performances [woodworking]](/img/logo.svg){kind=logo}
