Sliding glass door hard to open and close - Adjust rollers 

It says that grease is unavailable?? Which other would you recommend

@@sableduvall197 Good morning ☕️ If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/3Qz2ky8 😁👍🧰

Thank you as well. We appreciate you taking time out of your Saturday afternoon to reach out to us. Little things like this mean the world to us, let us know if you have any questions. 🧰

@@TheBlueDorito Thanks for watching, and we really appreciate you taking the time to share your thoughts and advice. The DIY community is the BEST! 😁🧰

Very cool, and you are welcome. Thank YOU! Great to hear our video was helpful. Reach out to us any time! 👍

My thoughts exactly! Didn’t even know I needed to know this just though maybe I needed to lubricate it!

I'm closing on a home in two weeks. This hopefully should fix both sliding doors! Thx

@@locohuero You are welcome, we are honored to help. 👍👍 to you for making it a DIY project! 😁🧰

@@valerie.mccaffrey Thanks for watching. 🧰

@@xxyy1282 Good morning ☕️ You are very welcome, we are honored to help. 🧰

@@Gkitchens1 Thanks for watching, we hope our video is helpful to you moving forward in adjusting your door rollers. If you end up needing to replace them, visit our video link below. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=S-JCIIH2mHVRnA7r 🧰

We are very honored to read this, much appreciated. Looking forward to hearing back from you on how it goes. 👍🧰

​@@DIYwithMichaelBorders I don't think he was able to get it fixed, unless he just didn't commnt back.😂

@@michaelbryant972 Let us know if you have any questions. 🧰

You are very welcome, we haven’t used WD40 before because it doesn’t serve the same purpose as lithium grease. Lithium grease is the product to use when performing this project. 😎👍

@@DIYwithMichaelBorders I used w40 to clean track and then the lithium grease spray you recommended and slides better now. Gracias!

@@joaquinsuarez6090 That’s awesome, WD40 to clean and lithium grease to lubricate is a great idea! 😎👍

@@YassamanFarmani Thank you so much for the ( Super Thanks ). We really appreciate that, we hope your DIY projects are going well. Please reach out to us any time you have any questions. 😁👍🧰

@@jameshaslam2048 You are welcome, and we are honored you took the time to reach out to us. What puts us in an even better mood is the fact that you are making this a DIY project. We love that! Reach out to us anytime you have any questions, the DIY community is the BEST! 😁👍🧰

Good morning, just poured a cup of coffee and am sitting down to answer any and all questions for the DIY community. Great to hear our video was exactly what you were looking for. Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Good morning ☕️ It definitely makes it easier to service the rollers when they are not on the bottom portion of the door and hard to access. What’s the update on your project, were you able to remove door from frame and replace rollers? Below is a link to our video showing replacement of these exact rollers on the bottom portion of our door. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=BZYlZu4yFuCIKy5r Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

You are welcome. You have beautiful weather in Orange County. I was just in Long Beach CA the last few days. We are back on the east coast now and enjoyed a great family gathering for Thanksgiving. Hope you had a great Thanksgiving day. Many more helpful videos to come! 😁👍

@DIYwithMichael orders no way I work in Long Beach memorial hospital off Altantic Blvd in Long Beach. Very nice sir. 👌

@@conchim99 Awesome, we were staying at the Westin Hotel on ocean Blvd. 😎👍

Good morning ☕️ you are welcome. We are honored you reached out to us and shared this. 🧰

You are welcome, we have a few options below. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-UNY99Q7Af0U.htmlsi=PJxMAFP8Q30M6m1h ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-nGLZTEFRv2I.htmlsi=uZ6G5zUVUuXM0kvA ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ilQjcOLd5gE.htmlsi=LyD1rHdg63bYV-CV Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Thanks for watching, WD40 will work however won’t be as good as lithium grease. Even lithium grease though is a temporary fix as we mentioned in the video. The best thing to do is lubricate the rollers with lithium grease so it buys you time to purchase new replacement rollers. You can pick a day that works best for you as get those old worn out rollers replaced. Below is our step-by-step video on replacing rollers. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=D9pAN18ketK5WWeh If you end up watching it, let us know if it was helpful. 👍

We appreciate that, thank YOU! 😎👍🧰

@@Telstar_1 Thanks for watching, any update? Is your adjustment mechanism on side?

@@DIYwithMichaelBorders No, I wonder if it’s covered up behind the PVC frame so not visible. I might try cutting a small amount back at the bottom at some point.

@@Telstar_1 Thanks for the reply. By referencing the sticker on side of frame, you can obtain the model number. This may help you locate better and more specific to your unit information. 👍

Good morning ☕️ we appreciate that. Bottom rollers are the ones to be adjusted, most doors don’t have upper rollers. 😎👍🧰

Thanks for watching, any update? This can happen if the lower rollers are offset significantly. Another cause is damaged or warped door…or warped frame that the door rests and operates in. Another cause is if the door was recently removed and reinstalled…it’s possible that the door is not installed properly inside frame where the rollers are properly placed on the slide track.

@@DIYwithMichaelBorders thanks for the reply! The bottom of the door and the track it sits on seem fine. What I noticed is that the sliding panel seems to have a bit of movement on the top & it seems to lean towards the fixed panel. Not sure if that makes sense. I wondered if there’s supposed to be something at the top keeping it at a certain offset from the overall frame. Someone told me this can happen due to the house settling over time and I can see that, but the question is if there’s anything at all to solve the issue, aside from replacing the door.

@@marlen.rumiantseva Thanks for the follow up, this is helpful information. Two things come to mind from here. 1. You may be spot on when you say that the upper portion of frame is possibly missing a piece that helps secure/align sliding door so it doesn’t make contact with stationary door. This will depend on your specific setup/install/and brand of unit. 2. The door is sitting a bit to low and because of this, it’s not fully being assisted and guided by the upper portion of frame that the door sneaks into. Basically the upper portion of door has more room to lean back and forth as it travels. This can be fixed by adjusting the lower rollers out/down, which in return will raise the door higher into the upper framed slot/guide. If the rollers are not adjustable due to their age/condition, they will need to be replaced. Keep us posted. 🧰

@@DIYwithMichaelBorders thanks again! I should have specified that there doesn’t seem to be or ever have been any kind of guide at the top. Another detail is that this door is at a condo that was built in 1971 & to be honest not sure if it’s original but I’d be surprised if it was ever replaced. I realize this is a bit of a unique situation & it’s hard to diagnose or find a solution without assessing the issue in person. I appreciate your suggestions. Thanks

@@marlen.rumiantseva We are happy to help. Keep us posted.

Thank you, we appreciate that. 🧰

You are welcome. 😁👍

You are welcome. 😁👍🧰

@@3mosewa445 We are honored to help. 😁👍🧰

Thank you, and you are welcome. 🧰

Good morning ☕️ any update? Are your adjustment rollers on top?

Thanks for watching. In that case, it’s best to replace your rollers. Out with the old and in with the new. You will have new rollers that slide very efficiently and brand new adjustment screws that can be adjusted with easy. Below is a link to a video of us, show me the steps of replacing these exact rollers. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=w3ozs_rhz8mpdYtX New rollers are very price friendly. Keep us posted. 🧰

We are honored to hear, thank you. Hope you have a great Friday night and enjoyable weekend. 😁👍🧰

@@lalo2641 Good morning ☕️ you are welcome. 😁👍🧰

@@DIYwithMichaelBorders ok

Good morning ☕️ you can apply some PBlaster to the screws which will break away and loosen up the rust and corrosion that has gathered on screws. If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/4aAGhPp Keep us posted. 🧰

@@DIYwithMichaelBorders Thank you so much for replying! I will give that a try!

Thanks for watching, any update? Have you insured that your lower rollers have been properly adjusted to the full-up and stowed position? Having your rollers adjusted up will give you the most room to shift door out of its trim insert.

@@DIYwithMichaelBorders it was basically a shit show. i adjusted the rollers down, by accident and essentially locked the door in place (open, no less). i literally could not budge it. ended up having to take it down completely and then clean/adjust the rollers. It slides, but still is not smooth. But its 30 years old. ill probably just get a new one come spring/summer

@@chrisi621 We appreciate the follow up. Being 30 years old, it’s a real good time to replace the lower rollers. Below is a helpful link that shows us replacing the lower rollers on this exact door. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=3gyHtc0MWy6YNddN You may find a very helpful. 🧰

Thanks for watching. 👍

Sounds like the wheels failed and need replaced

You are welcome, means the world to us that you took time out of your Monday afternoon to share a comment. Reach out to us any time. 👍

Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community. Very kind of you to reach out to us. Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Good morning, just poured a ☕️ and am sitting down to answer any and all questions for the DIY community. Thanks for sharing this. 👍 Let us know if you have any questions and hey if you’re interested, join our DIY ecosystem and help us grow an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Thanks for watching, ours is the exact same…no info whatsoever on the door. If you’re looking to replace the rollers, we will post a link to the rollers we purchased for this exact door. If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/3Jkj9JI These tandem rollers made the door slide like brand new once installed.

Thanks for watching, we can hopefully help. You may need a new track. If interested in purchasing this product, visit our Amazon affiliate link below. I earn from qualifying purchases. amzn.to/47qEuuC 👍

Thanks for watching, we can hopefully help. Below are two links, one shows removing door and the other link shows replacing rollers. 😎👍 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I8VmeHOT-y8.htmlsi=Fv5gsB3BJAeIlyiX ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Win-6GCcgy0.htmlsi=7LUQJlF43zn-nzBE Let us know if you have any questions and hey if you’re into crypto trading, join our DIY ecosystem and become part of an exclusive group of DIYers. toolboxtoken.com Reach out to us any time! 🧰

Hahaha

@@jacksonbennett84 what my lack of an arm? Or the thought of them pulling that on me?