Speed Queen Washer Not Spinning | Belt Installation. (AWN412SP111TW01) 

Glad it helped. Thanks for watching!

@@appliancerepairshorts thanks for posting! Literally took me less than 5 minutes to install the new belt and start tackling my laundry pile lol

Check your email I responded. Thanks

same here what's the fix

I having the same problem did you find out what was wrong

You push down on the center as you pull up on the bottom. The same way as the front clip

You can do it also, press the center down as you pull the end. Thanks for watching.

@@appliancerepairshortsmy situation ended up being that the center of the pump melted to the shaft and became glued to the shaft. I struggled for about an hour carefully wedging and extracting with a long flathead in order to break the melted plastic, but proved successful. Thank you so much.

To make sure I understand what you’re saying. The washer doesn’t spin in any cycle? So I would check the belt, the idler pulley. Remove the front cover and remove the drain pump. See now if it spins. Do you hear a humming? A bad capacitor. You can also check for power going to the motor. Send a model number. How is your lid switch?

I will let you know

Yes remove the front cover and check your belt. If you want to send me your model number I’ll find your belt part number

Hi, how are you? So how old is your speed Queen? Get me a model number. Can it spin?

Sorry I didn’t see your comment. You can also email me. Your question wasn’t too clear. If it is not spinning, check the lip switch, but also check for obstruction in the pump or the belt could be worn out also you have a capacitor, if you put it on spin and are able to partially spin by hand. If it spins, replace the capacitor. Hopefully you already got it

8:52 8:54 ​@@appliancerepairshorts

Olá boa tarde eu tenho uma speedqueen lavadora ela só lava mais na primeira lavagem ela não centrifuga entra a centrifugação e para e começa a entra água ae ela não enxaguar?

Hi Simon, the black residue is from the belt. From the friction and heat of the motor, the belt melted but i wouldn't worry about the residue. Just clean it off. It sounds like it may be overloaded or a bad/worn pulley. Replace the pulley if it's not turning perfectly smooth. The belts usually last about 6-7 years.

Probably not, but you would have to order special screws. You would have to have the screw holes in the pump feet. Or just order the clips. Good luck

I would need a model number. The leaking is probably from the drip rail edge. You might have soap scum blocking the drainage and it is spilling over. I’ll tag you in a speed Queen maintenance video.

I think you might have the belt on the wrong way. Or it it too big. When you say the belt is new, why are you changing it. What was the original problem?

@@appliancerepairshorts so the washer has been working with the same belt for over a year now. It was a while back when I replaced it. Has been used on daily basis It appears to be on the tensioner and pullys. I felt it with my hand and looked at it I can put the washer on a spin cycle. Sometimes it goes into spin but most of the time only pumps. No spin. **BUT IF I MANUALLY MOVE THE TENSIONER WITH MY HAND IT SUDDENLY STARTS SPINNING** at that point it will spin until cycle is over. I've looked a bit online but haven't found anyone experiencing this so far. If you think it would help I could upload a video of the inside of washer while it's operating so you can see what I mean

@@appliancerepairshorts I'm not changing it. What I meant was it was changed in the past the other one was freyd real bad so my point is that it's not a worn out belt causing it to slip. Spring was also replaced a year or so ago but washer has been used probably 100 times since then

@@BRWfilms got you, yes upload a video and email it to me. How is the spring tension

@@appliancerepairshorts I think the spring tension is good but I haven't taken it apart and physically checked the spring but I did look at it. I'm out of town till 25th. I will definitely upload a vid and email it to you when I am back. I appreciate you taking the time to get back to me!

I have a speed Queen, I’ll do a video on that later tonight

Thanks

With the pump still on , a man’s large hands will not fit behind the capacitor and behind that belt! My hubby had me in there trying to help. My hands fit all the way in but once I found where the dang top should hang I could not push down hard enough to set the clamp! After a long long time trying hubby finally took the motor out. Whew! Running like a speed Queen!

The link should be in the description, if you don’t see it let me know I’ll update it

Thanks for watching!

How old is your washer? You might have a brake that isn’t releasing. Try tapping it with a rubber mallet. Or you might have something caught in the pump or clothing in between the inner and outer basket