#95 Glass-like Finishing with Lacquer, Sealer and Drying Oil (Woodturning)

Quick Tip TUESDAY: Wet sanding on the wood lathe with Sam Angelo

ТУМАННЫЕ УРОВНИ В ПВЗ ТЕПЕРЬ НЕ БЕСПОЛЕЗНЫ! ВСЁ ИЗ-ЗА...

ЗАЧЕМ ЭТО РАСТЕНИЕ СУЩЕСТВУЕТ?! / PVZ 2

Qizim 94-qism (milliy serial) | Қизим 94 қисм (миллий сериал)

👊ЖЕСТКАЯ РУБКА КОСТЬ В КОСТЬ | ХОРОНЖЕНКО VS АГРЕССОР #mma #кулачка #мма #hardcore #хардкор #popmma

Spraying and Buffing Lacquer: Woodturning with Sam Angelo

WYOMINGWOODTURNER

Подписаться 70 тыс.

Просмотров 17 тыс.

50% 1

Видео Поделиться Скачать Добавить в

Sam Sprays gloss lacquer on a hollow form that he had previously colored. He first seals the wood with a lacquer sanding sealer, applies a spray lacquer, then wet sands to 6000 grit- then finishes by buffing the surface to remove any fine scratches. Buffing can be used to "cut back" the high gloss finish.
The following video links cover in detail the process of coloring, sanding, buffing and spraying lacquer on a lathe-turned project:
sanding playlist: • Sanding
Buffing: • BUFFING: Woodturning ...
Coloring: • Coloring a Hollow Form...
Coloring playlist: • Decorating w/Coloring,...
Buffing compound- www.amazon.com...
Thanks for watching my videos-
Please find my work on the following sites www.wyomingwood...
ETSY www.etsy.com/s...
Send me a comment or question via e-mail: @---- samandcheryle@gmail.com
I am now an authorized Robust lathe dealer. Please contact me if you have any questions.
Interested in a Robust Lathe-watch my videos below on these fine, American made machines.
The Robust American Beauty Lathe: A Closer Look • The Robust American Be...
For more information on the Robust Sweet 16 wood lathe, watch my video: Sweet 16 lathe tour tinyurl.com/uy...
Scout Lathe Tour…Video from Sam Angelo • Robust Scout lathe Tou...

Опубликовано:

10 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 44

@johncahall Год назад

Very nice and informative Sam. A fellow turner shared with me that he put the can in warm water before spraying the lacquer, and it really makes it thin out. I've tried it and it does make a significant difference. Keep up the good work Sam!

@WYOMINGWOODTURNER Год назад

Hi John, Yes I have used that "warming" technique. For this piece, I actually put the can in front of one of the heaters in my shop for 30 minutes or so., (No fear of the can exploding).... It is getting warmer here in Montana but the mornings in my shop are a little cool-as was the can of lacquer I was using. Sam

@jackthompson5092 Год назад

A very beautiful hollow form Sam.

@gregchapman729 Год назад

Very nice Sam, I am impressed with the look of that.

@jwhizhappymusic6900 Год назад

Great video. Easy to follow.

@carolriley8472 Год назад

Beautiful piece, Sam! The video was very informative and enjoyable!

@WYOMINGWOODTURNER Год назад

Thanks Carol

@chucksmith9633 Год назад

Many layers of lacquer will give you a thick coat because it melts into itself. Many layers of poly will give you many layers of poly because it just lays on the previous coat. My preference for lacquer is Mohawk. It seems more durable than the deft or watco. Thanks, Sam, for the video, beautiful piece with the added color.

@WYOMINGWOODTURNER Год назад

Yes I also have and use Mohawk when I use my "proper" spray gun. It is the best..... But when I am finishing on piece at a time, I just use a rattle can. Thanks Sam

@WYOMINGWOODTURNER Год назад

I did see a spray can of the Mohawk. I always have bought the gallon and used it in my spray gun.

@Ian-xy7xi Год назад

Brilliant stuff, thanks for sharing++++ Would be happy to see more finishing techniques

@WYOMINGWOODTURNER Год назад

Thanks, will do! Sam

@benyviaene7317 Год назад

Thank you ,Nice ideas 👏🏻👏🏻

@alwilliams9992 Год назад

Beautifully done. Another technique I’ll need to try. Thanks

@MarklTucson Год назад

Very informative video Sam. Appreciate seeing the steps to applying lacquer to get the finishes that you achieve.

@heatbill1261 Год назад

Thank you for sharing. Subscribed.. Liked.

@bernardfutter5327 Год назад

I really needed that instruction, Sam, thanks. Must make a similar spraying jig , rather than getting by with my turntable. Short of bench space, so inclined to use a T track and hanger bolt with wing nut instead of the clamp. Bernard.

@WYOMINGWOODTURNER Год назад

Glad it helped

@davidmorgan7522 Год назад

Beautiful hollow form that got more beautiful as you finished. I really like the color combination you used on that one. I've done a few of those but haven't had the color right yet. Guess I'd best get brave and make them a little thinner. Thanks for walking us through your process Sam! Take care, Dave

@WYOMINGWOODTURNER Год назад

Dave I did fairly well on coloring from the inside....much of this depends on the wood. Better to have a bit of luck with us.

@BurnsFilm 10 месяцев назад

amazing as always!!

@WYOMINGWOODTURNER 10 месяцев назад

Thank you! Cheers!

@jameswatson8630 Год назад

Outstanding, as usual. This is one where I take notes. Just one observation, when you're blasting through the grits 1800-6000, you don't feel it is necessary to wipe down the hollow form between the grits? Learned a lot today. You say finishing is simple, but there are all the little steps that you take that make all the difference that I would have never thought of doing. Now I am going to watch your other video on how to color a hollow form. Many thanks for sharing your craft, much appreciated.

@WYOMINGWOODTURNER Год назад

At 15:30 into the video I do clean the surface with paint thinner. I will definitely clean the surface every time I spray more product on a piece. However, I am using two forms of abrasives that don't really produce a loose grit that might stay on the piece. First I use Mirka abrolon pads, and then I use pen turners abrasives that are cloth backed. Neither one has a loose abrasive that will cause issues later on like a regular sandpaper will. Another example.....I don't usually sand with the lathe going forward AND reverse. I sand in reverse when I think it is necessary. But you will hear from some turners that this must be done all the time. Another rule??? I clean off the surface when I feel it necessary to do so. But thanks-you are very observant. Sam

@markwalsh3561 9 месяцев назад

Good job, well done. I have used lacquer for many years on furniture and cabinets but I cannot find lacquer here in PEI, Canada.. Thanks, Sam.

@joliekarno Год назад

Lovely.

@WYOMINGWOODTURNER Год назад

I am not sure what you are asking here. "to Part will wax"??? Sam

@joliekarno Год назад

@@WYOMINGWOODTURNER it was a typo but I got the answer, thanks.

@oldgeezer1746 Год назад

I like the color pattern on the burl.

@WYOMINGWOODTURNER Год назад

I give nature all the credit ... any third grader could do the coloring.

@kensurratt2729 Год назад

I need to try that technique on pens. I'm doing the CA glue and also the Glu Boost This looks maybe easier

@WYOMINGWOODTURNER Год назад

Yes this works really well on pens.

@randsipe224 7 месяцев назад

You aught to try Mohawk finishers choice, better than deft

@WYOMINGWOODTURNER 7 месяцев назад

I do use Mohawk lacquer when I spray with my Finex gun Sam

@leemunch4591 Год назад

Thanks for another excellent and very informative video Sam. I have one question. Can a cellulose sanding sealer like Mylands be used instead of the lacquer based sanding sealer?

@WYOMINGWOODTURNER Год назад

I am not familiar with that brand. But if it is a cellulose sanding sealer it should work. Perhaps try it on a scrap piece of wood first however, Sam.

@glencrandall7051 Год назад

The result it outstanding. But I question the necessity of going to 6000 grit. Can the human eye and touch really discern the difference between say 1000 and 6000 grit finishes? Thank you for sharing. Have a great day and stay safe.🙂🙂

@WYOMINGWOODTURNER Год назад

That’s a very good question Glen It’s all about hiding the scratches from the previous grid. With a very shiny surface like this, they are quite visible to me at least. Another thing is once you get to 800 or 1000 grit. It doesn’t take much sanding to progress through the grits. I might spend 20 or 30seconds sanding at 2400 and above. I guess it’s just the way I do it. Thanks, Sam.

@user-xm4xc7qy2f Год назад

Nice piece, enjoyed your video. Do you always use a high gloss spray lacquer? Have you ever tried using a semi gloss or satin lacquer spray to get a less shiny finish?

@WYOMINGWOODTURNER Год назад

That’s a good question. What I do I am for a really high gloss to begin with then when I buff it I can cut the gloss back a bit whatever finish you are using gloss is harder and will hold up better than a satin or semi gloss.

@gerardverzaal4666 Год назад

Beautiful globe! Why so you use a cold room to spray lacquer?

@WYOMINGWOODTURNER Год назад

Well, this is my "cold storage" room which means it is unheated. But we are much warmer now in Montana. So it was fairly warm. I did actually warm up the can of lacquer I used. So the cold storage room was probably 70 degrees. Sam

@latherookie Год назад

Who are you?

@WYOMINGWOODTURNER Год назад

I am just a guy turning in my shop, making RU-vid videos-780 so far. Thanks for watching. Sam

Далее

#95 Glass-like Finishing with Lacquer, Sealer and Drying Oil (Woodturning)

23:37

#95 Glass-like Finishing with Lacquer, Sealer and Drying Oil (Woodturning)

Просмотров 119 тыс.

Quick Tip TUESDAY: Wet sanding on the wood lathe with Sam Angelo

20:02

Quick Tip TUESDAY: Wet sanding on the wood lathe with Sam Angelo

Просмотров 56 тыс.

ТУМАННЫЕ УРОВНИ В ПВЗ ТЕПЕРЬ НЕ БЕСПОЛЕЗНЫ! ВСЁ ИЗ-ЗА...

00:41

ТУМАННЫЕ УРОВНИ В ПВЗ ТЕПЕРЬ НЕ БЕСПОЛЕЗНЫ! ВСЁ ИЗ-ЗА...

Просмотров 707 тыс.

ЗАЧЕМ ЭТО РАСТЕНИЕ СУЩЕСТВУЕТ?! / PVZ 2

00:47

ЗАЧЕМ ЭТО РАСТЕНИЕ СУЩЕСТВУЕТ?! / PVZ 2

Просмотров 477 тыс.

Qizim 94-qism (milliy serial) | Қизим 94 қисм (миллий сериал)

43:30

Qizim 94-qism (milliy serial) | Қизим 94 қисм (миллий сериал)

Просмотров 677 тыс.

👊ЖЕСТКАЯ РУБКА КОСТЬ В КОСТЬ | ХОРОНЖЕНКО VS АГРЕССОР #mma #кулачка #мма #hardcore #хардкор #popmma

00:11

👊ЖЕСТКАЯ РУБКА КОСТЬ В КОСТЬ | ХОРОНЖЕНКО VS АГРЕССОР #mma #кулачка #мма #hardcore #хардкор #popmma

Просмотров 817 тыс.

Spraying Lacquer With HVLP - (GREAT FINISH)

24:09

Spraying Lacquer With HVLP - (GREAT FINISH)

Просмотров 131 тыс.

My Favorite Food Safe Wood Finish for Tried and True Original Finish non-toxic wood bowls Video

16:06

My Favorite Food Safe Wood Finish for Tried and True Original Finish non-toxic wood bowls Video

Просмотров 146 тыс.

Wood Turning Easy High Gloss Sprayed Lacquer Finish

14:29

Wood Turning Easy High Gloss Sprayed Lacquer Finish

Просмотров 24 тыс.

High Gloss Finish For Wood Turnings

17:08

High Gloss Finish For Wood Turnings

Просмотров 70 тыс.

Turning incredible bowls with a colourful finish - by Emma Cook.

26:02

Turning incredible bowls with a colourful finish - by Emma Cook.

Просмотров 143 тыс.

Another approach to applying CA glue to a Pen

10:25

Another approach to applying CA glue to a Pen

Просмотров 61 тыс.

5 Reasons for Woodturners to Wet Sand!

12:25

5 Reasons for Woodturners to Wet Sand!

Просмотров 33 тыс.

Understanding the 40º-40º Grind with Sam Angelo

23:51

Understanding the 40º-40º Grind with Sam Angelo

Просмотров 68 тыс.

The TRUTH About OB Shine Juice!

19:21

The TRUTH About OB Shine Juice!

Просмотров 6 тыс.

Woodturning - The Most Hated Wood In The World?

8:38

Woodturning - The Most Hated Wood In The World?

Просмотров 88 тыс.

ТУМАННЫЕ УРОВНИ В ПВЗ ТЕПЕРЬ НЕ БЕСПОЛЕЗНЫ! ВСЁ ИЗ-ЗА...

00:41

ТУМАННЫЕ УРОВНИ В ПВЗ ТЕПЕРЬ НЕ БЕСПОЛЕЗНЫ! ВСЁ ИЗ-ЗА...

Просмотров 707 тыс.