Spyra 2 and Spyra LX Faulty Problems | FIX 

Well done for making this honest review. These water guns are expensive, and most RU-vid videos reviewing them, are not critical enough to base a good judgement on. 👍

Why is your video titled “Fix” when you didn’t provide a fix?

Thanks for the upload same thing happened to me faulty now I will follow your lead and email them. Gutted it was broke on the same day we brought it

I also had a problem with my spyra lx. I have been using it for a short time and then put it a site for a while and when we were going on vacation I brought it with me. And right at the time to have some fun I started pumping up the water and it took forever after pumping for a long time i finally got the gun on pressure and when I took it out of the water a lot of water came out the front of the gun just like yours. the next time I had to inflate the gun again I saw that with every pump movement a lot of water came out of that hole at the bottom so then I thought hey this is not good. now I'm always like I'll see if I can solve it myself if not I can always send it to spyra 😜But I found out that there was a break in one of the check valves of the water gun now I must also say that I do not find that strange because you put a lot of pressure on the inside of the Water gun so why is that piece of plastic so thin there is enough room to make this much stronger so I thought this was really weird. Now I glued and reinforced the housing myself with the help of a 22mm copper pipe, I sawed it open and gently beat it over the plastic so that it now Many times stronger than before and the water gun works like new again. I think spyra can pay more attention to this part because you are putting pressure on the gun and so there is a lot of tension on this part. And I think for the money they ask for the gun that this could certainly be made a lot stronger.

I had same issue. took mine apart. a clip came off that holds the bellows to the nozzle. it might not have been tight enough. fixing it tomorrow.

Thanks for the video. So what is the fix?

I got my tuesday 4/24/23 and it worked perfectly till today 4/29/30 and same thing is happend, stuck at 32% and won’t shoot and when I release wanted only a tiny bit comes out.

So your tip is to email support. Nice

Did you have to have a recipe or record with them i bought them from a third party

donde lo compro

Hi , do you have the email address at spyra? My spyra 2 has the same issue sticking at 32

Mine gets stuck at 23. Whats the problem? How to fix this problem?

Yes, Stuck on 32 here also!

My spyra 2 is not refilling it’s getting stuck at 23-24-43-44-45.

Thanks, I used my Spyra 2 for the first time yesterday and an hr into using (or less) exactly the same loading problem occurs. It is stuck on 23% and wont fire at all. You mentioned there is a fix for this? Is there a link to the fix video anywhere? Thanks for posting.

I got a defective Spyra 2 from a Co-worker for 50.00 bucks. I took a chance on it seeing that he only bought it a few weeks prior and I figured that it would be an easy fix (told me that he was upset with the Company). Turns out that my co-worker was getting the run around from Spyra and then they stopped communicating with him altogether. He told me that the rubber bladder inside the water gun was ruptured (after I bought it) and that he had asked someone at Spyra to send him a replacement bladder (free if possible or pay if necessary, he just wanted to fix it himself) The company stopped responding to his messages after he requested the replacement bladder. I'm now stuck with a perfectly new looking Spyra 2 that does not work (yes we're still friends). Does anyone know where I can get a new water bladder for the Spyra 2 or a substitute that will work for it?

I have the same problem😢

Had my spyra 2 for 2 weeks...used 4 times. Issues out of the box with leaking out the drain hole and also mystery yellow liquid (rusty solenoid?). Then on a charge it went bang and it seems the bladder exploded inside...what a waste of cash 300AUD!!!! I was in discussion with spyra on the email about it and then they blocked me sending any more responses 🤣 Avoid this company!

I bought two spyra 2's and one of them isn't unloading /loading :( It tries to shoot but it's empty. I'll try emailing them also..

On both guns you’re not sticking the nozzle in up to the fill line. It doesn’t draw up water from the barrel, it draws up from the middle gills.

I have also spyra 2 with the same issue. For this value it shouldn't happen.

Mine WONT FILL UP-- please help