Step by Step Install: 2014 Tacoma Compustar Alarm/Remote Start. 

Thanks for taking time to make this and this video helped a bunch!

Excuse the green wire and the pink wire which vehicle wire is connected to. 

Can you clarify whether the Blade needs to be programmed/flashed before installing into the Compustar unit? Or does the programming happen when it is installed, the wiring all done correctly, and then the vehicle started?

Yeah i've done that several times/I have the install guide in front of me . I've printed it and I have it on the screen😁. The problem is that on the connector the wires are not at the same pin location as shown on the install guide.Two of the locations given on the install guide are empty on the connector, Those 2 are TX and RX. At the location of the parking light I see a different color wire.

Great video! I;'m from South America (Ecuador) And I was able to install a compustar 7900AS everything works but the remote start :/ just tries to start and nothing. Can you help me please? My car sienna 2011 3.5 with the key to start the vehicle (the one with the G symbol) Thanks!

Is there anyway you can help me out with a 2007 tacoma. Starting doing it already and can't get the red light to flash green did it the same way as your video and now I'm stuck

So this should be exactly the same as a 2005 ya? Great video!

Hey Goodday. I'm from the Netherlands. Here we sadly have no compustar dealer. So I'm depending on fellas like you to properly install my system. I have the compustar 7900AS. I bought the Al Blade and flashed it allready. I want to install this in a Toyota Prius V 2013. I have the install guide from idatalink. From Bulldog security i have the vehicle diagram from my car. I have several questions. On the install guide they showed a fuse of 7.5 amp by the 12v input of the main harness . Must i replace the 30 Amp with this 7.5 amp( a very big difference !). I assume that i only have to use the the wires/connections shown on the install guide of idatalink.

hello, I really liked the video, I congratulate you, I'm sure I'll lose help to see if you can do it for me, please make a video programming a compustar cm-7200 alarm, to adapt it to a 2017 golf gti, how can I move the safety locks agency along with the original alarm or if you will have an email to be able to communicate greetings

Will this work without the blade? Cus my 9900AS kit did not come with it. I am installing it in a 1998 Isuzu Trooper.

Goodday I encountered some difficulties installing the unit. It appears that the location of some of the wires dont match with that from the car. In fact on this specific connector (L7)none of the location shown on the install guide are correct. The colors with the specific wires are there but they are at different locations. These wires involves two data wires RX and TX and the other is the parking light. What can i do to find out which wire is the correct one? I purchased a wiring diagram of my Prius V 2013. but is little hard to find the connector on the diagram.

Hi did same alarm install ,also bought from same place as you everything works just truck lights come on but no crank am i missing something using a AL BLADE but that is what the sent me programed already ,thanks for any help

Where did you buy the module trying figure out how I get the settings changed so I buy from correct place

Installed the same kit onto my 2015 tacoma and all works except the horn, looks like it was overlooked in the video. What was the cable that controlled that again?

still got that J32 teggy?

Great video, but Sir who do you think I am. I would not attempt this, those wires look like a maze of confusion. I thought maybe I'd try to look at this video but yeah I will leave this for the pros. Thanks for the video though.

The TB blade is always necessary on any vehicle?

How did you change the green/white to the starter 2?

So where does the pink wire go i don’t have an immobilizer/blade?

One more question You said the blue is ignition one . I hear other guys saying the blue is ignition 2. ?