Super Bee low voltage cutoff & glitch sensitivity, Gas RC Kill Switch, Killer RC 

Thank-you for this video I will try this out next Sunday I've been having some problems with one of my two Killer RC switches. This is a must have for 1/5th r/c cars and trucks.

It is needed. A low voltage battery can cause a runaway. You can switch it to 3v, but you can't totally disable it.

Nice job on explaining it. I which I had on.

can we still make it work on a 2 channel avc, with fail safe with the adaptor liked to steering like in previouse killer bee swich? thanks btw link to order it if is possible to. w the conector devisor for 2 chanel reciever and radio please

hello, recently I have installed a kill super bee, but I see that the led light is in an orange tone similar to red instead of being in blue ... they took models with other colors or perhaps I have something wrong connected. Greetings and I hope you can help me.

and what about voltage, 2s LiPo battery have 9v+ when fully charged, need i put some BEC ? (RX spectrum comes with losi 5ive, servos: hitec HS-5765MH, and stock Losi 5ivet steering servo)

Would you want low voltage cut off to be like 7.3 for 2s lipo? If my lipo goes to even 6.3 it won’t charge as it says it’s voltage is too low. Having a 6 volt cutoff I’d imagine won’t help 2s lipo users. Maybe I missed something?

Hi i have a Losi 5T with a Spektrum DX 3R Pro i have the stock 6V battery and the stock SR3300T receiver i have it all setup. Low voltage set to 4v and Glitch sensitivity at 1 it goes through the start process then the LEDs go out and then i get solid green and flashing red at the same time. i have tried my AUX channel in P2 and P3 also i have tried frame rate at 16.5ms and 11ms still solid green and flashing red at the same time. Not sure what I'm doing wrong thanks Phil.

I did every single test And I notice if you or if the coil cable get disconnected from the supper bee kill switch the engine still running. I tape my around to make sure will not comes off

about bad cell, i don't think so. Can you give me a link to this LiPo

how can i disable lov voltag catoff, i use 6v NiMh battery

I jut put the kill switch in and it sweet ! I have the new Hitec servo kit from ddm it comes with the 4s batt does it come with a solution

The batteries are on our website. See link in video description. I guess you are having a low voltage problem? You never explained why you wanted to change the cutoff. Please email me info@KillerRC .com

so I hve a question will this kill switch work if for say my battery comes disconnected?

last time kill switch turn off the engine after 30 minutes running with 5100 NiMH battery with 4v cutoff, i found it strange cause battery was just charged and must be running more then 30 minutes, maybe it cause of NiMH battery lost voltage when get some big load from servos.

will this switch work with my nitro buggy?

Just installed the super bee on my 30DNB and 30DNT and the instruction manual is wrong. It’s states #1 switch as volts sense #2 switch as glitch sense Following the instruction manual had us scratching our heads until we watched this video and saw you use dip #2 to cycle the volt sensitivity. How come no one has mentioned this 👍🏼

it was only one time, actually i want to disable it because i think that this option isn't need with NiMH battery and can cause some problems, like at that time =)

You can only change it, not disable it. Why do you want to disable it? With a 6v battery you should have it at the factory setting of 4v. If the low voltage is being tripped then you need to charge your battery or get a better battery pack.

I turn the radio on and it turns red and I turn the radio off it turns green

no it couldn't be, because i turn on engine again a few times and it continue running, until i made servos work, at this time voltage was 4.2-4.5v

A fully charged 2S LiPo is 8.4v. I don't like using voltage regulators. The servos are stronger and faster. Myself and many others run a straight lipo in our Losi 5IVE without any problems, but the slight risk is still up to you. We have discussed this a few times on our various RC forums. RCLargescale . c o m

Or maybe the battery has a bad cell. Put a volt meter on it while you move the servos. Switch to our 6000mAh LiPo RX pack and you'll have plenty of power!

then i will switch it to 3v and look what happened =) if it was a battery then problem will be again.

Or maybe you just had a radio glitch and it has nothing to do with the battery?