Swag Offroad Air/Hydraulic Ram Mount Install

Подписаться 567 тыс.

Просмотров 153 тыс.

50% 1

In this video Tim will show you how to install Swag Offroad's Air/Hydraulic Ram Mount kit on his JD2 M3 tube bender, converting it from a manual bender to a hydraulic bender.
Swag Offroad - www.swagoffroad...
Website: www.bleepinjeep...
FaceBook: / bleepinjeep
This product is meant for entertainment purposes only. Your mileage may vary. Do not try this at home. Void where prohibited. Some assembly required. For off-road use only. Slippery when wet. Batteries not included. Do not use while operating a motor vehicle, heavy equipment, cherokee XJ, wrangler TJ, wrangler JK, or any Jeep vehicle, especially the newer Fiat ones. How-to videos may be too intense for some viewers and children under 30 years of age. Please remain seated until the 4x4 ride has come to a complete stop. Studies have shown viewing these videos causes increased cancer risks in laboratory test people. I am not a professional, I have no training, I'm not even particularly good at horse whispering. Don't believe everything that you know. Please keep your hands in the vehicle at all times. Do not tap on glass. Do not eat anything that has been on the floor for more than 3 days. Keep your hands to yourself. Not to be taken internally. Reproduction strictly prohibited. Driver does not carry cash. Objects in Bleepinjeep mirrors may be farther than they appear.
09521

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 70

@tims_4x4_garage 6 лет назад

The swag adapter really makes this bender so much more user friendly. The best benefit, as you mentioned is having a setup that doesn’t need to be bolted to the floor. Really handy since you want a lot of room around your bender and you don’t want it bolted to the center of the garage. Lol. The return spring is a great addition.

@seko6056 2 года назад

this bender is one of few that make so easy 90° bend. Well done with the upgrade

@arcturusbbqsausagemaking2435 6 лет назад

Great video As a retired welder fabricator of 27 years its nice to see someone run a beautiful bead as good as I used to Lol. !! ..... Nice job

@endoskeleton99 8 лет назад

Great video and super nice welds! When I get my JD2, I will do the exact same upgrade. Thanks for the tips!

@CncObsession 8 лет назад

Maybe use some trampoline springs to make the return automatic with the knob only. Great video.

@DAVE94LIGHTNING 3 года назад

Best video on the Air/Hydraulic conversion yet. I just bought this exact same set up. Only thing you did not explain is how much of a pain in the butt it is to push the ram back manually. Buy the Swag elastic spring kit it is worth the $50 Thanks.

@MyBridgestone24 5 лет назад

Just ordered a JD2 Model 3 and the Swag kit. Going to be a great addition to the shop. Great Video.

@markpinther9296 8 лет назад

Thanks for this. Excellent job narrating and demonstrating this. Mp

@RottFink 9 лет назад

Fantastic upgrade! Looks like I'll have a new tool to buy here soon... Thanks for the great video. Keep up the great work guys.

@valveman12 9 лет назад

Very instructional video. I have purchased a lot of products from SWAG and they are always well made. BTW: Nice clean welds.

@talon0863 9 лет назад

Good job - nice welds too!

@CasperRc81 5 лет назад

I could be wrong a friend of my built a 90* square frame with a mount plate and gusset. Mounted the tube bender and the frame plugs into the receiver of his truck your not bolting or moving that vehicle. We live in Az so weather is almost always compliant.

@BruceBusby 6 лет назад

That's some very nice looking welding beads!

@mxcollin95 2 года назад

Dude nice welds. That setup is definitely on my list of tools to get! Did you buy that stand for the tube bender or make it? That stand looks solid!

@elijahperez159 3 года назад

My ram started leaking on the ram end as soon as I torqued down the bracket on it, I hope it stops

@pavelshanin8636 2 года назад

Спасибо за видео. Очень помогло в моей работе в гараже.

@jeepingneatus 5 лет назад

Super helpful video. Thanks

@ttenrabyrral1 7 лет назад

Great Video!! Need a measurement PLEASE. I plan to fabricate a JD2 Model 3 bender to use with JD2 dies and need to know the benders arm spacing. I found good drawings for the hole size, location and spacing on line but have not been able to determine the distance between the bender arms. In other words, how long is the 1" OD spacer in the die follower mounting arms? The spacer that the ratchet bar mounts on. Thanks!!

@SubZeroSpecialists 5 лет назад

Nice clean video Tim. I'm more interested in the stand as are others. Can you make and sell them?

@josecunha731 6 лет назад

... strange the things we notice. I see your water heater in the corner, and remember how anxious I am to convert mine to a tankless electric to reclaim that little space in the garage. ;-) The perils of having a shop in a small garage. Great video though, one of my next projects.

@josecunha731 6 лет назад

Also really wish my welds looked as good as yours.

@rheidtech 9 лет назад

Great piece and affordable. Good stuff.

@boomstickkid 2 года назад

How big did you make your base plate for your stand? Mines currently only 12x12 but that’s cuz it was mounted to the floor. I was thinking 24x24 but should I make it bigger, I don’t want it to be too tippy when loading tubing.

@RedneckGarage 9 лет назад

Good information - not sure I would buy a 400.00 tube bender then add on hydraulics on top of that cost ....

@sjeverett75 8 лет назад

so would you just spend the 700+ to get the hydrolic version in the first place? This method still comes out cheaper and you don't have to do it all at once.

@mitchdenner9743 6 лет назад

sjeverett75 it's actually eight hundred bucks for the hydraulic version and it only gives you hydraulic piston with it you still have to buy Power supply hydraulic pump 900 bucks for the electric pump or 500 for the air over hydraulic so you're looking at 1200 minimum and 1600 maximum and you still have to buy dies

@ronmiller682 5 лет назад

Very nice I need to get the whole assembly

@YankeeCherokee 9 лет назад

Are you going to build a roll cage or something with the bender? Very interested in how you'll use it

@bleepinjeep 9 лет назад

Maybe. I'll be making all kinds of stuff with it. I didn't buy it for a specific project. Simply adding to my at home fabrication abilities with this setup. - Tim

@YankeeCherokee 9 лет назад

BleepinJeep Alright thanks for letting me know. Be sure to tell us about the things you make with it!

@PatinatruckGarage Год назад

Do you have info on your rolling stand

@neskhymontoya2096 4 года назад

Great video. Does anyone know if the JD model 3 is consistent to the model 32's dies, in particular the dies for bending square tubing?

@320MN 7 лет назад

What is the size of your mount plate on your stand? Are the holes centered on the plate?

@SubePelayo928 3 года назад

Any issues with the ram not extending at first?

@Arkansasdisc 8 лет назад

The JD2 manual says to torque the bolt for the handle (that you have to remove for the ram mount) to around 71 ft/lbs (IIRC). I added my Tam mount and torqued to factory spec and it seems far too tight. it doesn't allow the ram mount to swivel and the ram extends. Dis you run into this? Are you torqued to spec? Did you just hand tighten?

@Arkansasdisc 8 лет назад

sorry for typos. *Did *Ram

@SpokesandRotors 8 лет назад

How large of a compressor do I need to operate that ram? CFM, etc?

@kennethstephens8046 9 лет назад

Nice knife. What brand and model please?

@chukchee 6 лет назад

Do you have plans for the stand?

@lucinorosas7066 8 лет назад

how much did you pay for this bender, l need bend 100 pices galvanice pipe. 1 foot long each, 30 degrees.

@Backtheblue-xo8mv 6 лет назад

I have a harbor Freight 90 amp flux core will it be safe to weld that

@krisdjsteel 5 лет назад

Cameras are affected by electromagnetic fields. You’ll fire your camera at some point if you keep doing that.

@darkmage4446 7 лет назад

do you know what the bolt size is that they use? and ram size?

@darkmage4446 7 лет назад

like whats the width of your air ram

@patrana2222 4 года назад

Cuántas toneladas es eso 30 TN o 20 TN especificame saludo peru

@CHIBA280CRV 5 лет назад

Fantastic thanks

@johnridley1038 5 лет назад

Great Video, However, how come you had to weld it yourself?

@MrMrsregor 3 года назад

you can buy it already welded for an additional $34.95 on the swag offroad website. however, most people that have/buy a hydraulic tube bender are buying it because they already weld

@epride38 5 лет назад

what size is the tubing you bending? gauge?

@mohamedf1739 4 года назад

احسنت يارجل

@earlywins32 9 лет назад

Were you welding with your hh140? What's the thickness on the swag brackets?

@bleepinjeep 9 лет назад

Yeah, sure was. The swag ram mount is 1/4" thick. Thit was definitely the limit of single pass welding with that machine. I wasn't able to burn the welds in as hot as I would have liked with my hh140 but it welded it strong enough that I'm not worried about it coming apart. Works for me! - Tim

@mrshudson5705 7 лет назад

Nice weld

@TheDakotaThurmond 8 лет назад

You didn't torque it...

@tjs_welding_and_fabrication 9 лет назад

Wow. That thing takes forever to bend. I have the same bender i converted to real hydraulics. There i a vid on my channel. Otherwise good plug for SWAG.

@lucinorosas7066 8 лет назад

how much did you pay for the bender?