Swingarm bearing replacement - 1984 ATC 200X 

Thank you sooo much !! Not gonna lie the screw driver in the sprocket truck in seconds! Magic thanks again!

Never know what to expect from you Bert but it's always an adventure sometimes educational laters

All that work now you got to take it out for a run around the yard have some fun. 👍👍😀🇨🇦

hammer time...good job bert

Been using the double wrench trick for years🔧🔧works great.

Always something to do no matter rain or shine later

Burt u work the same way I do hammer persuader and wd40 lol gets the job done everytime!

Nice 👍 I’m taking mine apart right now and I didn’t know for sure if the disc holder was threaded or slipped on because it wonk move

I enjoyed watching you work on this while cord stripping on time lapse! Nice work!

There is always something to learn from you BERT great 👍

Your beekeeper did wheeler sometime back turn out great

Late to reply however, fill all those voids up with grease, everything condensates which leads to corrosion. Keep up the content. I'm heading for the same repair soon and wanted to visit the alumni at the good ole University of RU-vid

Great video

"Getting a bit rusty in there, lucky we got to it now rather than later" , let's see 1984 to 2021 = 37 years, mmm, lucky we did not wait until 40 years to have a Bo - peep. Thanks Bert some of your mechanical video's convince me to pay the premium and get a professional to do it. Had a flat battery on my Ford Escape this morning and Auto membership attendee said he did not carry a 4044 battery but gave it a quick charge to get me where I was going and he said to ring up my Car membership later in the day and organize with them for a replacement battery. Did so and the second bloke who turned up this afternoon with replacement battery was spitting chips because replacing a battery on a Ford Escape was a 45 minute job and he was most cranky with his associate who turned up earlier and did not carry that particular battery. The interesting thing was that after installing the new battery and I then took it for a spin, I found half a dozen of the electrical gadgets. ( ie the thing that turns off you engine to save fuel when you stop at traffic lights) all suddenly started to work again, although my dealership could not get them working at last annual tuneup. My "Two bobs worth" says that due of the Covid *19, I have only traveled 5000 kilometres in last 12 months so various electrical gadget don't work after your battery amps are to low due to lesser charging. Wonder when the dealership will wake up to this fact. Now to find a professional dealership to do my next annual service. does such a place exist Bert.

Hi Bert another great video nice content stay safe bro regard 👍💪💰❤️

Dupro plastic paint. Works great. All your tools, you need a chain break. Great video Bert.

Hairspray is how I used to put grips on spray bar they slide right on then glue themselves there

good video.

wet sanding for plastic then clean and re-do it then get plastic spray in can and apply make sure to match the color then dry and wax n buff.

Drill and tap that outer tube housing for a grease fitting. Take the inner seals out of the bearings. Pump it full of grease. Heck, I'd still do it while assembled. Grease the drill and tap while using, clean chips and re-grease to catch as many chips as possible. Enough grease pressure will still get it through the inner seals. We used to use Pledge furniture polish on the plastics. Cheapest (Aquanet) hairspray for installing grips.

love it

You need to invest in a 1” knooter wrench. They are next to the Sky hooks & Board stretchers.

Bert, you should buy some emery cloth, it won't remove any metal to mention but it works really well for prepping shafts for the race and bearings, easy to use as well

Wow

I put a grease fitting in the center to grease them last longer

Something on a wet day to do...😄😄

Just for the record if'n you paint the exhaust I recommend Rust-Oleum Automotive High Heat Spray.. I have had great experiences using it on exhaust system !

Restore plastic with mothers mag and aluminum polish. Mainly used by those in the know for yellowed headlight plastic on your car. check out a youtube on mothers headlight fix.

Guten Tag aus germanii 👍 👌 💪

Çok güzel video 250

Just as i was going to ask you if you put that inner pipe in you said shit. Then that was that.....to funny

Heat gun for the plastics. It will melt the imperfections and bring the luster back

Light oil on a cloth or I'd say put some more material on it with some kind of spray maybe clear coat, then sand and polish. I wouldn't sand or wet sand that old paint right from the get, I bet it's real easy to go to deep . Try a couple methods on a small piece first then once you find one you like do the rest.

Great job bert.Looks like your sprocket carrier bearing is gone.It makes the sprocket loose like that.

The ceramic coatings put a shine on the plastics

Try code in the Plastic with WD-40

I use heat gun to liven my plastics back up. It brings the color back out and use plastic filler lightly and use the heat gun to fill it in the grooves/scratches. GO SLOW!! It will melt the plastic if u use too much heat

Even though they are sealed units, why they did not put grease fittings also is beyond me!!! Turn the bar you were hammering around once you un stuck it on the second barring!!! Happy Holiday Sir!!!

Kansas rain all day today it be rain for 2 week and 3 day next week

Bert! wear glasses when using a wire brush!

Bert....have you never heard of a dead blow mallet??

Do you like the new Ryobi batteries I’ve had them do some weird things on a cordless angle grinder

Hit it with a torch plastic turns brand new

Good stuff but no test ride? aaaaaaaw

Great video. I'm not sure if I missed it but did you put that metal tube back in that goes between the bearings inside the carrier? Thanks

How's your roof holding up with all this rain? Remember a while back you were up there patching away. You caught a great sunset as I remember. Btw, love your Beauty Parlor chair! 😊

Hey you still have that teal chair , I see , it's nice

LOL you got that can of lube setting there just a pipe would have been better to knock that out

You ever purchase something and say who is the jack ass that worked on this before me.... Pipe wrenches, adjustable wrenches, sledge hammers...

I have a couple of questions Bert. I use Ryobi tools too. I got a one plus impact wrench for my bday and wondered what sockets you use with it? The Kobalt ones I have don't fit the wrench the opening is too small. I like my Ryobi tools and don't want to go buy something else that will require more different batteries. Let me know. Thanks

#abs #Plastic #Star Brite!

Use a hot air gun to bring back the shine of the plastic parts.

👍👍👍💜💚🧡🤗🥰

We broke it??? What is the WE stuff. I was just looking - didn't touch it.

Should have put a greese fitting in the middle of the swing arm never have to bearing again

Hey Bert, Did you hear about Ryobi’s zero turn electric mower? I know you love Ryobi!

Are you sponsored by " Croc's " Burt lol.

Was this the quad in a different video you see for sale on side of road

all constructive criticism I hope you understand that Im old school and follow you religiously no no no not anti seize in there you want them sealed bearings to fit tight no lube of any kind if you wanta hit that bearing after its seated use the old bearing againt it NEVER hit the inner race please

Hey Burt. Love the videos. I cringe when I see you beating on that mushroomed tool with no safety glasses on. I have a friend that lost one eye that way. It only takes a second for that end to chip off and get you.

Now take the axle back out and put the disc on it

Use a Scott brit pads on the plastic

clean up that mushroom head on that bar bert, dangerious

#dude omg with all you know.. How could you just about murder that bearing .... Hitting it in the center you just about killed the center race . why didn't you take like a um 1" 1/2"' socket or a match the outter race...or even using that copper headed hammer would have been better ? No doubts you distorted the ball carriage also... UGH =P

Little bit of diesel fuel will shine em up

alot of work better get some enjoyment out of it

This video proves that not everyone should repair vehicles

Put the tools down mate Holy f#%k