Yamaha Rhino 660 Wheel Bearing Replacement

Подписаться 11 тыс.

Просмотров 19 тыс.

50% 1

How to replace wheel bearings on the Yamaha Rhino 660. I did the front wheel bearings, but the rears are going to be very similar.
Tom's Tinkering and Adventures would like to thank you for joining me in my adventures! Comment, Subscribe, and most of all, be inspired to live your own adventure when the time is right!
HELP SUPPORT THIS CHANNEL: I hope you enjoy the material that I offer, if you would like to support my channel there is a link below. Take note that it actually goes to my wife's account! She supports me in my adventures. Bless that woman!
DONATIONS: www.paypal.me/...
FOLLOW ME! If I'm on a motorcycle adventure, I take my Spot-X GPS tracker with me. It allows my family and friends to keep up on my progress and see where I'm at. The link below will be updated every time I get ready to go on a trip. share.findmesp...

Опубликовано:

11 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@Trytocookthis 3 года назад

Nice project. It's a sporty beauty and I'm sure it is fun. We gotta take care of the things that bring us joy. Nice vid. ;)

@TomsTinkeringandAdventures 3 года назад

We have fun with this beast, the Rhino is not as fast or fancy as the new side by sides but it's paid for and has been pretty reliable.

@Mr69barracuda 3 года назад

I already knew how to do this.. but it's been a lil while so I watched for confirmation. The only thing I did different was add a lil Heat to the hub (While bearings were in the freezer) to expand it and then Blaster penetrating oil before beating the bearings out of it. Cleaned the housing with a wire wheel- then sand paper to smooth out the rust ring under the seals, then blaster penetrating again for rust prevention. I then greased the seals in and out for easier assembly and sealant properties. great #video! No Big intro music carp. or intro "Look at me I'm Mr.. Blah- blah Fluff"

@TomsTinkeringandAdventures 3 года назад

Thanks, if you watch some of my older videos I do intros and bla bla…😂😂. Good tips for making the job a bit easier and better!

@audrybella6405 2 года назад

Thanks for the helpful video. I bought the bearing rebuild kit from my local Yamaha dealer for $32.00. Included two bearing and three (different) seals.

@TomsTinkeringandAdventures 2 года назад

That’s a good deal considering it’s all in a kit. Hope it goes together well!

@Silverado2000 Год назад

Doing these now remember don’t do what I did don’t run your bearings until nothing left of them my hub nut welded itself to the cv got too hot and had to cut it off😂 thanks for the video man

@TomsTinkeringandAdventures Год назад

Ah, been there before!

@parkerriverrat1 3 года назад

thanks for the video I have 8000 miles on my 2006 Rhino 660 would like to do all the wheel bearings someday. So far everything is still moving smoothly.

@TomsTinkeringandAdventures 3 года назад

Take your time and it isn’t too bad of a job.

@MrBajabug65 3 года назад

Good call on the center spacer! Could totally see that being a "DOH!" moment!

@TomsTinkeringandAdventures 3 года назад

I know a guy who has forgotten it before.

@TheBCSledder Месяц назад

The easiest way for removal ive found is to weld a rod to the inner race and pound it out

@TomsTinkeringandAdventures Месяц назад

@@TheBCSledder that works great if you have a welder. I have one, but I don’t use it enough to be proficient, should get it out and practice a bit.

@Trytocookthis 3 года назад

I like shopping on those websites that show me what other people bought when buying the same thing I'm buying. Maybe the seals would show up. LOL.

@TomsTinkeringandAdventures 3 года назад

I should have done a little bit more research before starting this job, would have known to get those seals. Fortunately it's not too difficult to change them out after the fact....but I still haven't done it!

@craigchristlieb5840 3 года назад

What size is that hub nut? Thanks for the video!

@TomsTinkeringandAdventures 3 года назад

I probably used a 1 1/4” socket, but 32mm is what should be used.

@terrybaltzer7484 2 года назад

Take the seal out of the bearing remove the ball bearings.Then the centre will fall out then take a Chisel and brake the outer race.

@TomsTinkeringandAdventures 2 года назад

There’s a few ways to get it done. I’m using my press next time! 😀

@brunow6101 23 дня назад

What is the torque on the axle nut? Thanks

@TomsTinkeringandAdventures День назад

Looks like it's 190 lb/ft.

@alansterling3481 3 года назад

how about getting an arbor press?

@TomsTinkeringandAdventures 3 года назад

Arbor press is a good way to do it as well. Most people probably don’t have one. Hammer and a vise or maybe a big C-clamp are likely to be more common. Hey, it’s good to see you here again!! 😀