Swordfish 200a esc, Water cooling Install Deltaforce 35 Fast Electric Rc Boat 

IMPORTANT INFORMATION: The swordfish controller doesn't like delta winds.,the higher amp ones. Or low numbered winds like the neu 1d winds or less. So you guys will not see this one in action. SORRY

I would be interested to see you test how hull-shine affects performance and speed!

I'm no expert when it comes to rv boats, but I probably would have removed the ESC mount, and just layed the ESC front to back flat on the battery try in the center to get it as low as possible, then mounted the batteries along the sides of the hull like you showed. That would help keep the wiring and cooling lines out of the way if you decide to run 8s, and have all the room you need to shift them to get your balance right. You have a lot of fun projects. I can't wait to finish my boat and get it on the water for the first time. The scouring of the hull should work to improve speed. 1/1 Jet ski riders/racers have been doing it for years and the real fast guys claim a noticable increase, maybe 5mph or so on some skis.👍

You should put everything in it and look for c.g. at about 1/3 with room to adjust it a couple of inches because of 6s and 8s weight diffence.... then glue everything. Probably end up with esc left next to motor (also helps with torque roll)... If that doesn't fit, esc in front of motor and lipo's on sides. Should be a very good hull to go fast...

Check this out I don't know if you already do it but you probably do cut you a little piece of Hose the same kind that you're using for your Cooling say maybe an 1/8in wide and slide it over top of your hose instead of using a zip tie to hold your hoses on your Barb fittings looks good and works well yeah the black hoses looks good I just switched mine up to White for a change something different. and your connections on your ESC and your motor look awesome what are those 8 mm? I like your water test too never seen that done that's a good way to check it before it hits the water like you said cause what runs hot don't run long

Yeah thinking about putting the same ESC in my Pursuit yeah do the video where you have it pulled up on the computer that'd be cool I'd like to see that

*The video keeps me surprised. Great R/C, it's really cool. 👍🏻😀👊*

I got black hoses on my boats but i used hose from windshield washer on cars i am a mechanic so i had lots lol

Black lines look killer. More easy on the eye.

How did you like the swordfish 220 amp ESC is the data logging pretty cool

Your videos are excellent if I was to critique anything it would be you repeating your words which gets annoying.

What's the dimensions on your bearing ID OD and width or if you got a number on it would be great and I got to hook up on bearings I can get you top of the line bearings for cheap

WHEN I BUILT MY 3 POINT HYDRO BACK IN 1970 I HEARD TALK OF GLOSS AND FLAT BOTTOMS. IT REALY ISE"T A NEW IDEA.

lmao that's great. For your next trick I want to see 8s in a ul19. Great video sir.

Hey big b sand your hull front to back 😁👍 no side side 👽

I love your videos I have learned a lot from you I just got through gutting and rebuilding a miss geico 24 . I balanced the prop and had to modify the stuffing tube and pretty much everything and all thankfully to your videos

If it was proposing for a while that will take out bearings so you might want to check it your serfice drive also as well as motor. Cool build!

I'd like to see that comparison with scoured bottom please bud

Hi mate i put my receiver in a small balloon and cable tie it up somewhere so water doesn't destroy it 🦘👍😁.

that things gunna fly on the water with that esc!!

This was great B. I had to post it on the community page bro. That esc is 🔥

26 minutes video😓

I am interested in those escs u turned me onto ose i was wondering about the refurbished stuff if it was any good or not

Love Hifei swordfish esc's got a 300A pro and a 200A pro lite my self and datalogging is the best tool ever for rc boats. Nice to se some cool update on the df 35 😁 jus bewear tha if you use PC and USB link move the hifei file from C:\progamfile to C:\dokument or a new file you make . If it is location are progamfil it has a tendens to say error . my computer \ dokuments \ hifei v4.11 is how i did it to make it work .

Another awesome bit of tinkering Big B 👌 That's a really neat layout, getting that ESC in with the rest of the gear. Nice work bro 👏 Can't wait to see her running with that Swordfish... should be 'x' knotts and (hopefully) no smoke!! Love the orange and black combo with the inlets. That colour combo works so well. Here's hoping that .187 cable is for the Shrimper build! 😉

U gunna do a 8s run ?

what KV is that motor ?

What's your email address bud.