Taranis Q X7 Quick Tips: Setting up and using/showing telemetry (RSSI etc.) 

5 years later and we are still watching these...thank you, much appreciated.

This channel is an absolute treasure trove of useful information. I wanted to let you know how appreciative I am of all the work you put into this content. Thank you sir !

Wow. I bought this radio 2 years ago, but never knew how to do this. Now that my Long Range quad has GPS, i wanted to get coordinates printed out on my screen. This made it super easy to figure out how to do that. Thanks!

Thanks for this one,saved me a shed load of messing.

Thanks mate, very useful 😁 adding this so I can keep an eye on my fishing drone!! When I'm flying it out to sea 👍

this was great, just what I needed in here. thanks!

I love the "Painless Pill" on the radio! It looks great there!

Thx again Painless. Yet again another great instructional vid. 👍👍👍

Wow thank you man you helped me so much!!!!!! Thank you keep doing what you love bro❤

#Painless360 thank you so much for this video, I’m a new pilot and this info is priceless to me... 😎👍

Excellent info. Super helpful!

You are the best!! Thanks!!!!

nice video, thanks for that

Thank you so much.

Beautiful thank you very much

Hi, thx for the vid! What is rxbatt monitoring? Is it same as vfas?

Súper helpfull

Great video! Is there anyway to have the RSSI spoken every few seconds?

Just what I was looking for and explained very clearly as always. Can you tell me how do I now get an audible warning of low values while flying. Many Thanks.

Great video. Just one question, how do you decide when it's low? My RxBt shows me 3.1V, but my LiPo checker shows me 3.58V in each cell. It's a 2C 7.4V 1300Mah battery. Whats going wrong here? Is RxBt the value of 1 cell? Could someone help me out? I just want to let it to play an alarm at 3.4V/cell or 6.8V total.

Your video solved some of my problems. Because I am an electric powered flyer, I want to monitor the flight battery and not just the speed control or ESC output voltage. I am also using the frsky X8R reciever. Is this possible and how do I hook up this receiver? Thankyou for reading this

I sometimes get telemetry lost randomly and in a second its back. Cant figure out why have just updated all rx tx firmware and still a bit sketchy. Wondered if you had any weird things like this also what range are you getting with this set up (approx):-)

Thank you so much. That helps out a ton. My only problem problem is I was thinking I could do rssi for the xm+ since it has a port but I think it's only for maybe osd rssi reading?

Hey there Painless! Thank you so much for this tutorial I've done everything you told in here, but my RxBt is always frozen at 4.8. Either with a fresh battery or a used one. Can't seem to solve this. Could it be a bad Rx?

Thanks for the vid.. A little off topic I did a search for this on your channel but thought I would ask.. Do you know how to delete a mixer?

Really struggling with getting the right value 99 in my osd mine reads at 9 🤷🏻‍♂️

hey my qx7 is being stupid it won't let me select a switch it has worked fine before now but when I go to inputs and try to put a switch to a chanel I flick the switch nothing and doesn't show them in the list

I very much Enjoy your videos I have now built 4 multi-rotors and each one I go back to your series :-), perhaps I missed it but I am using cube with RFD900 telemetry / mission planner and a Taranis on all my copters.. the rc radios are d4r2 on the first 2, X8R, and RX8R .. could you point me to a video that would pass telemetry (battery, flight modes and height) to the Taranis? I know there are scrips with additional hardware for the x8r rx8r but was hoping an easy way to simply pass the telemetry to the Taranis - Thanks!

Can I get it to call out % instead of db?

Hi! Could you please tell if you have to do something special to make Taranis (i own X7) show "Type" on Telemetry page? I do not have one. Also tried to discover sensor - no luck. I own the KingKong ET115 drone.

Do you know a frsky mini receiver that will fit on a 250 size quad and do this too?

sir, I want to ask. beside the battery indicator on the monitor screen there is a signal bar indicator for telemetry. and the signal bar is only 1 bar and it can't be full and there is always a warning voice from the system. how to disable the signal bar? Thanks for your help.

I tried to do this with my xsr, but nothing is discovered. Anyone else have a simillar issue?

Do you have a video on how to set up RSSI or RQLI on a Taranis Q X7, and a 4-in-1 module from a Turnigy TGY-IA6B receiver (AFHDS 2A)? I'm using OpenTX 2.2. Module firmware is version 1.2.1.18, or newer. Thank you.

Lee. When I discover a new sensor via my Qx7, one of the sensors is A2. Is that my primary battery level? If so, the telemetry is showing 11.9-12.0. If I check the battery with a battery checker it's showing fully charged at 12.5. There's a bit of a discrepancy there. Just curious if I'm understanding this correctly. Thanks!

When I click, Discover new sensors nothing shows up even when I have the RSSI channel 12 mapped to my taranis, I move my remote and the % changes. I have an FrSky XM+ with a taranis qx7. I also noticed that in the telemetry window inside the Taranis for Source : Default and I cant change the value. Thanks for your videos !

For this procedure you need to update the receiver? I have XM Plus. Can activate a voice alarm for RSSI when 45 db? Tx

how do i set an alarm? or is it configurated by default?

can this bind to dsmx/dsm2

My Taranis X7 could not discover new sensors from L9R. Please help

mine doesn't find any sensors

hello everyone, on my Teranis q7S I cant set up low/high rates in mixer. any help please

My telemetry screen looks different. I am having problems with A2 readings.

I have a qx7 and for some reason it's only going to page 9 how can I get to the telemetry?

My source is null and I can't not see any sensors

Why i haven't got RSSI? 4:00

Hey painless long time watcher first time caller. 😂 I'm having a problem with my KISS FC. If you don't mind could you help me out. Please and Thank you. Check out my video I posted on my channel. It's the only video I have.

Hay Painless360, great video. I tryed to get RSSI and receiver voltage from my L9R receiver, but when I go to discover new sensors, it doesn't find them. Whay is that? L9R has RSSI.