TEARDOWN: C3 vs B3 Parkside Performance PDSSAP 20-Li impact drivers 

I am the same as you! I don't use these tools to earn my money with them. I use them for DIY mostly. As you rightly observed I am concentrating on the cheaper tools hence the "Broke Life EU". Parkside at the moment I think see to be the best of the cheap tools, however they are slowly but surely prioritising profit more and more above the quality of the tool. I talk about the 5 year warranty at length, because as Lidl are a reputable seller I presume you could take them to court and not that they will for sure rule in your favour but you at least still have a chance. Whereas with ebay and aliexpress, good luck after the tool is delivered. However I do understand what you mean by after the second year it is up to the seller. As the mandatory warranty period in the EU is 2 years they will do a lot in those 2 years and after they are up they will start coming up with excuses no doubt about that. However you still have the 5 year claim on your side in any case. It stands to reason that if you make enough noise and the right one even after 4 years and 11 months they should acknowledge the warranty. Provided of course the tool is in the state they want it to be in, which is basically unused. And finally I want to say sorry you had to go through that, it is not a nice situation to be in. Not knowing what they will do with something you paid with your hard earned money for. At least it turned out in some positive way, not the best for sure but still OK. Thank you for the sub! It really means a lot! I don't ask for likes and subs on my videos, because I want to know that the people who decide to subscribe, leave a like or comment really want to be here and like the channel! Thank you for your time and I hope to see you around the channel!

No worries. Pleasure is all mine! I am glad I did it to notice the bent fin on the motor in mine! And generally yes a bit of cost cutting here and there as they do.

@@BrokeLifeEU Bent fin can be for balancing purpose

120Nm and 150Nm it should do easily. It can even do 200Nm with a full battery and heavy socket.

​@@BrokeLifeEU Just an update, I burn two of those impact wrench. First one, worked even on 170 nm on wheel nuts, but after that, tried to test it again with 126nm but on "Expert" mode from the app (I saw on this mode that all leds were on, so I thought this mode is more powerfull than "Performance) and it blocked, wasn't able to unscrew 126 nm, tried a few more times until it started to smoke. Return that, bought another one, again on 126nm didn't work, tried different nuts, undo them with a wrench then torque again 112nm, nothing and I saw that the engine was working but the anvil wasn't moving... this time I returned everything back, batteries and the impact wrench. Second experience with parkside but this time was a fail. I know, that wrench it's not for wheel lug nuts but I was thinking to change the anvil if it would have worked 😢

​@@BrokeLifeEUMaybe it'a a double standard? In different countries, in my case, Romania... Or the manufacturer change as you said in a previous video about c3... I saw a lot of tests with b3 wrench on youtube, and they were doing great job, c3 only on your channel and even though the b3 seems to be better than c3, c3 was doing a good job also..

​@@sebastian9020c3 e slab rău față de b3

Accu 4 Ah 20 V bluetooth ❤

For the smaller wood screws I would always use a drill. It provides me with way more control and precision. I'll reach for the impact driver if the bolt is big enough to demand it. Otherwise the drill is my choice. That is why U use the other big lag/wheel bolts to show the power of the tool. However one must keep in mind this is above all a low budget DIY tool so it ca never go head to head with a Makita. The C3 especially. They have cut down on cost so much when I compare it to the B3 that even against a 10 year old Makita I am sure the Makita will be the better tool.

@@BrokeLifeEU ya i know they're crazy cheap and sometimes you can live with the limitations and sometimes you can't. sometimes you can even fix it like when they forget to grease the tool or sawdust gets into the motor like on their sabre saws which they keep selling with that defect

Unfortunately QC is appalling in some cases. On the other hand I must admit it is because they are so cheap that I managed to buy my first power tools. I never had money and still don't for a brand new Milwaukee or DeWalt. Especially as I only use the tools from time to time and don't use them for my job at all. In time I of course understood the vast difference between Parkside and a proper Milwaukee or DeWalt but I think there is a place under the sun for Parkside. Only if they paid a bit more attention to their QC and a bit less to their profits. But that is impossible. I am sure...@@UGPepe

Wrong. For precision you use drill drivers, for power you use impact drivers/wrenches .

trigger sensitivity is a common isue on brushless drivers. I have a 1 year old brushless 18v makita and it has the same dead zone in the start. If you want really precise low rpm control you need a brushed one.

I would say the performance is slightly less than the B3 ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-UcQ6JfIK-yQ.html As for the parts they look like a downgrade. Especially the motor. On the B3 the fins are closely fused together and on the C3 there are little gaps in between them which vary. So it is not like it is a feature or something.

Better fan design on c3,better cooling.

I hope it has a warranty! I would say it is best to return it and get a new one or your money back! Which model is it?

Да, B3 и C3 са еднакви по отношение на преобразуването на 1/2" наковалня.

If you want the warranty to stand 100% I would say don't open it and don't do anything to it. Just use it like you would use an impact driver.

@@BrokeLifeEU thank you for the quick response, I appreciate and value it

No worries. It is my pleasure! In most cases manufacturers will go after anything in order to not accept a warranty claim. Although I have been lucky and I have never had an issue when I have had to resort to a warranty claim I would still advise people to be cautious. As I believe Parkside say somewhere that if any evidence of misuse or commercial use is found the warranty will be considered invalid.

On the side you see pictured you can see the brand "Parkside" and model number. On the opposite side you have another sticker with more detailed information about the tool. There you can find the manufacturer. For Parkside branded tools they are mostly one of three: Grizzly tools, Kompernass or OWIM.

You are quite right sir. Mine is made by Grizzly tools. I hope these are good. @@BrokeLifeEU

I hope they are too! At least they look like they have plenty in reserve. So if anything goes wrong they can replace them quickly! @@ps7539

I think it will be a long wait for the next version. And it seems to me more and more tools are being made by Grizzly so even less of a chance to get a C4 version by Kompernass. But all things considered I don‘t think it is too bad for that price. Providing you got a good one!

🎈

Sure! As soon as I find another B3!

@@BrokeLifeEU I have finally been able to buy a new b3 in a second hand app, I'll take some pictures and send you, if you want

Sorry about that, was a long day and I only made the video as a person requested it in the comments. As per the defect, look at the fins on the motor from the C3 one of them is bent... Also the fins I feel on the C3 are not fused together as well as they are on the B3.

în opinia mea B3

@@BrokeLifeEU Stii de pe unde s-ar mai putea cumpara B3-ul? Pe Romania vad ca singura optiune e OLX-ul. Multumesc!

@@oanceaandrei9652 Cred că doar OLX acum. Nici măcar Lidl.de nu le mai are.

@@BrokeLifeEU Am inteles. Multumesc! Pe OLX am vazut ca a bubuit pretul pentru B3. Inseamna ca sunt chiar bune.

@@oanceaandrei9652 Așa cred. Am văzut multe versiuni C3 stricate acum.

B3 is indeed very good. It's a shame they are difficult to find now. It's like the old A1. The people who have them don't want to sell them and that is completely understandable.