Test Batteries with a Multimeter - Collin’s Lab Notes

Подписаться 449 тыс.

Просмотров 55 тыс.

50% 1

Find all manner of multimeters at Adafruit:
www.adafruit.com/category/637
Test a battery & get acquainted with multimeters #adafruit #collinslabnotes
Visit the Adafruit shop online - www.adafruit.com
-----------------------------------------
LIVE CHAT IS HERE! adafru.it/discord
Adafruit on Instagram: / adafruit
Subscribe to Adafruit on RU-vid: adafru.it/subscribe
New tutorials on the Adafruit Learning System: learn.adafruit.com/
-----------------------------------------

Наука

Опубликовано:

30 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@christopherjones4785 3 года назад

they need to be tested under load. that is why you use a resistor. 100ohm for AA-D and 4.7kohm for button cells.

@TerrariumFirma 7 месяцев назад

but what which wattage? i have found them on ebay but it specifies 1/4 watt. Is this suitable for testing AA batteries?

@xray2518 6 месяцев назад

Super quick and to the point. Some might say direct. Thank you ❤

@Helal_Tech 11 месяцев назад

The comforting voice ❤

@mrlithium69 3 года назад

If only it was this straightforward. I have a drawer full of "dead" batteries that still read 1.25-1.35v. The only thing I have left that doesnt draw enough current to still work with them is an analog clock. I would estimate "Super dead" is like 0.7v, it is impressive you found one with 0.267v

@jasonvoorhees3282 Год назад

Different circuits work on different voltages. A clock may work down to 0.7, but there is a very simple circuit that is called “Joule theif” which works down to 0.3v

@johnsellers9623 9 месяцев назад

You are not getting a precise reading because you need to test them using a resistor to be accurate.

@do7hemath937 10 месяцев назад

The cheap red DMM that harbor freight used to give away just for coming in the store has the selection to check batteries ...................THE CORRECT WAY.......under a load. Good 1.5 volt batteries are 4.0, 3 volt ( alarm keypads ) are about 8.1 & 9 volt batteries are 25 mA.

@candeffect 2 года назад

Nice and fresh = fresh

@greentechnology3529 3 года назад

Now connect the nominal load to this cell. For example, the bulb for the Maglite Solitaire flashlight type LK3A001 (1.5V krypton). And measure the tension again. And how do you know how to do it, maybe the load current?

@johnsellers9623 Год назад

Yeah that’s not correct information those batteries can both be junk. Has to be under load.

@remi1771 Год назад

I'm not sure why but i'm seing my standard AA battery read 80v...

@notrandom2 Год назад

I don't see "0.267"... I see 267.2 Can anyone please explain?

@janluisantoc702 11 месяцев назад

It showed mV or millivolts. To convert it back to volts, divide it by 100.

@debdootkumar4832 10 месяцев назад

267 millivolts & 2 microvolts

@spacenodus7959 2 года назад

👍

@marcmicari7659 7 месяцев назад

Unless you use a joule thief then get down to nearer 0v....lol

@phoperdox_sore 3 года назад

I have two batteries where both measure around 1.4V, but when I install one of them into a analog clock, only one of them works. May have to check the short circuit current as well. But good shorts anyway!

@phoperdox_sore 3 года назад

Indeed Still wondering what is causing this type of voltage behaviour in terms of the battery chemistry welp

@bsathya4 3 года назад

@@phoperdox_sore someone once told me to add a nominal load (resistor) to the battery while testing, under load is when the battery must perform. I am yet to try this.