No video :(

Test review of MP1584 0.8 to 25V 2A DC-DC Step down converter

Подписаться 108 тыс.

Просмотров 67 тыс.

50% 1

In this video you will see the voltage regulator MP1584 module is tested under the following conditions:
Watch 5A 50V Converter with WiFi App Control WZ5005 : bit.ly/wz5005
*** Purchase Electronic Load from **
Amazon Canada: amzn.to/3e2Zluu
Amazon USA: amzn.to/3huyXf3
All other Amazon:
AlExpress: s.click.aliexp...
Banggood: www.banggood.c...
** Purchase Arduino Start Kit **
Amazon USA: amzn.to/3z88F9G or just UNO board amzn.to/3aY7KOL
Amazon Canada: amzn.to/31an88J or just UNO board amzn.to/3pYxSNN
Amazon Europe (all Europe): amzn.to/3pMCHge or Just UNO board amzn.to/2PgGItD
AliExpress: s.click.aliexp...
Banggood: www.banggood.c... or UNO board www.banggood.c...
eBay: ebay.us/B1JWLi
***** Purchase Authentic Arduino Uno from ***
Amazon USA: amzn.to/2KApAwK
Amazon Canada: amzn.to/37LZ8sW
All Europe Amazon: amzn.to/36YDSzn
Input 15V output 9V at 3A
Input 15V output 9V at 2.5A
Input 15V output 9V at 1.5A
then at
Input 12V output 5V at 3A
Input 12V output 5V at 2.5A
Input 12V output 5V at 2A
Input 12V output 5V at 1.5A
View the datasheet for MP1584
www.monolithic...
Tutorial by Ahmad Shamshiri form Canada
****************************
Arduino Step by Step Course (over 100 lectures) Starts here • Lesson 00 What is Ardu...
****************************
If you found this tutorial helpful, please support me so I can continue creating contents like this. Here is PayPal link paypal.me/robo...
Follow me on Facebook robojaxTV
Follow me on Twitter: / robojaxtv
Follow me on Instagram: / robojax
Tutorial by Robojax.com
Get other projects code and learn Arduino
robojax.com/lea...
*** AFFILIATE PROGRAM ***
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Опубликовано:

5 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 143

@camelCased 2 года назад

Thank you for the tests. The results are what everyone would expect, there's no way a bare MP1584 with no heatsink could handle 3A. So, these modules are OK for sub 2A projects, and even then it's better to use a heatsink. I'm going to buy a few for my low-powered (sub 1A) projects.

@Way2Short2Watch 8 месяцев назад

same

@EJEuth 8 месяцев назад

Very nice review, thank you for sharing. One comment about the smaller module: This module Not based on MP1584, but either MP2307 (Vin < 23V; 3A) or MP1482 (Vin < 20V; 2A), both using synchronous rectification - that is why they don’t need the Schottky diode (as not found in your video at 2:44), which is mandatory for the MP1584 (larger module). I just discovered when I bought 5 of them and zoomed in finding an MP1482.

@robojax 8 месяцев назад

Thanks for the info!

@andrewemileski8004 3 года назад

Measure the voltage across the boost capacitor, pins 1 and 8, and if it is less than 5 Volts under load then the input voltage is too low (minimum Rds(on) is spec'd at 5 Volts). A good starting figure is Vin >= Vout + 6 Volts. For 9 Volts out, it needs 15 Volts in. Under-voltage lockout (UVLO) is 2.2 Volts on the boost capacitor, and it charges through a switch and diode. At high loads > 65% duty-cycle, the boost capacitor has less time to charge and may require a higher input voltage. All this is in the datasheet. Also, the 4.7 uH inductor is too small for ideal performance.

@flightisallright 6 лет назад

12 to 9V is a small delta. The module probably also has a max input current.

@lebasson 3 года назад

Fantastic overview, exactly what I wanted to see!

@robojax 3 года назад

Glad it was helpful!

@tui5978 3 года назад

Tôi muốn mua

@vaastafraja5685 2 месяца назад

@@robojax My friend will this do 4.2 lithium battery down to 3v?

@upendrachaudhari4635 4 года назад

i was going to choose mp2307 earlier for powering my esp8266 since it is easily available, for commercial project. Now i have dropped this idea, need to read spec sheets very carefully:) MP2307 has typical switching frequency of 300KHz while MP1584 has Fsw 900KHz and goes to 1.5MHz (though not recommended). So MP1584 is superior in every aspect. Now i am just in dilemma whether to use ACT4088 (typical Fsw 1.2MHz) or MP1584 (typical Fsw 900KHz), both are strong. Assuming higher the switching frequency less ripples in output voltage, only disadvantage it is non-synchronous and hence less power efficient.

@alexeinovember5491 6 лет назад

It is two different modules with two different ICs! Large one is MP1584, smaller one is MP2307! You can see that smaller one have no diode on output because it is synchronous converter! MP2307 is more efficient but input range is 23V vs 28V for MP1584

@swapniljoshi9997 5 лет назад

@Mai Mariarti Which one can be used to charge mobile supplied variable DC input? Will it be safe?

@swapniljoshi9997 5 лет назад

@Mai Mariarti Hi, i want to use an alternator hooked with bridge rectifier & smoothing capacitor. Then use one of these to charge cellphone. Input DC will be varying while output DC (5V) should be constant. Which one is better in mentioned scenario? MP1584 or MP2307?

@MMaheshThakur 5 лет назад

u saved me man

@MastercraftKARIGAR 4 года назад

@@swapniljoshi9997 you may use any of them just set voltage b4 plugin device

@Freedom1776usa Год назад

good info. thanks for contributing. I use these little converters all over the place and never have any issues. I dont push them though.

@tomb2623 2 года назад

i hear that adding an output electrolytic capacitor of 100uf (LOW ESR), improves performance greatly.

@sziamiau1 3 года назад

Unfortunately you do not use ESR capacitors on the PCB ! There are only the most necessary parts for the PCB to work!

@jj74qformerlyjailbreak3 Год назад

Very informative while performing robust test. Thanks for your time.

@diorthotistm1621 2 года назад

Thank you for the thorough testing, that was very enlightening.

@robojax 2 года назад

You are welcome. The best thank you for me is to subscribe to my channel. Thank you.

@mohammadjavadfarshid1804 3 года назад

thank you. these module benchmarks have been very useful for me

@celem1 3 года назад

There is inadequate thermal mass (copper area or heat sink) for the higher Amperes but the thermal shutdown was too fast at 2.5A. Possibly you had insufficient cool down between experiments? Also, Chinese chip markings are suspect more often than not. A real MP1584 should handle 3A. Possibly these are deficient copies of the MP1584.

@SomeRandomGuy_id Год назад

my question is will it work fine if the supply is an unstable dc supply like an output from bridge rectifier of motorcycle altenator. Thank You for this comparison.

@alfredonovoa8124 6 лет назад

Thank you for the reviews. It would be interesting to know the efficiency of the converters.

@robojax 6 лет назад

You are welcome. You are right. I have done for some other modules and forgot to do it with this. I'll keep that in mind. Thanks

@edism 4 года назад

Thanks you just saved me 14 mins, that's exactly what I'm here for lol. I've bookmarked your channel and video for future reference @Robojax, thanks for the upload all the same.

@justusbungener283 6 месяцев назад

@slybunda 3 года назад

if you vary the input voltage does the output voltage stay fixed to what it was set to? e.g set output to 7v but input voltage fluctuates between 9 to 16v? would output remain steady at 7v?

@robojax 3 года назад

if the input voltage is variable, then yes the output will stay stable regardless of changes at input. This has variable input and will keep output fixed.

@cyberbeast1789 2 года назад

I've been using this mini buck converter for my direct to PV/Solar panel 100w to my 12vdc fan. is it normal that it gets very hot on start ?

@jomfawad9255 2 месяца назад

Please if i connect battery to this and then this to breadboard, how much current in amps maximum i can then take from the breadboar

@robojax 2 месяца назад

For sure 2A is not a problem with the breadboards

@FilmFactry 3 года назад

So withe the larger D-Sun version, I warned to use it with my 3d printer's 24v PSU to give me 12v for a strip of LEDs. How odd that its input voltage is 23v not 24v. Who has 23v as standard?

@monipilli5425 3 года назад

I AM USING LM 2596 IC BUCK CONVERTER , I NEED TO REDUCE SOLAR PANEL 22V TO 12V....BUT NOW INPUT AND OUT PUT SAME VOLT....PRESET ADJUST ..BUT NO CHANGES OUT PUT VOLT ...WHAT IS THE REASON ....

@BigMTBrain 5 лет назад

Testing for 3 amps is invalid as the specs are "1.8A Sustained " for the Mini360. I couldn't find the sustained value for the Mini MP1584EN, but it surely is not the rated 3A peak for both boards.. As far as I know, "peak" means "short transient"; therefore, not "sustained". Keep in mind that the specs for either board CHIPS are different than the specs for the BOARDS, as according to the CHIP spec sheets, the BOARD designers select from a list of support component values, which set the characteristics of the BOARDS.

@robojax 4 года назад

Hi, If you see the datasheet, it is rated at 3A www.monolithicpower.com/en/documentview/productdocument/index/version/2/document_type/Datasheet/lang/en/sku/MP1584/

@AngelOrtiz1 Год назад

I have a battery drill I would like to step from down 20v 2a to 12v at 1.5 amp to another battery drill I wonder if the module will handle i...t thanks

@robojax Год назад

first I don't remember what was the maximum current I tested. let's say it was 1.5A, then yes.

@serkanozkan8793 4 года назад

this regulator one of the most efficient for this price and size. How ever I need bigger one, I really did not see much efficient than this in bigger scale. What should I do, should I cascade them ?

@robojax 4 года назад

yes can.

@davidbolha Год назад

Hi, Can I use this Mini360 to step down the voltage of an 18650 battery to ~ 3,2 V ? 🤔😕 Thanks ! Best Regards,

@ACOnetwork 3 года назад

That was interesting, thanks 😁

@robojax 3 года назад

Glad you enjoyed it!

@graywoulf Год назад

Does the set output voltage change with different input voltages? This is an important point of interest to me.

@robojax Год назад

of course not. the output stays as long as you don't bed below the minimum. This is true for all converters.

@FilmFactry 3 года назад

I just order o few of the larger size. What gets hot? would a small heatsink fix the issue. Is it the coil or the chip?

@robojax 3 года назад

Yes it will.

@diydsolar Год назад

Hi, have you tested buck converters with CN3903 ? Thanks.

@robojax Год назад

Hello, see my channel on Energy and power called WattHour youtube.com/@wattHour

@alexandrupopa5920 2 года назад

A very good review.

@arielbene2013 2 года назад

Hello robojax ... I'm following your work thank you. I need a good step down module that can handle 18v to 8.4v 2A. What do you recommend? Would you help?

@robojax 2 года назад

Hello, I have review of Step Down Convert also called "Buck converters" you can search my channel. but his is the best one ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ErqyxBvkdPk.html

@rctechmods8165 3 года назад

I have 4.2v lion cell and I want to use it to step down the 4.2v to 3.6v for 1watt led will it work or not I know I can just simply use current limiting resistor but as the battery gets low the brightest of led also gets low ( I think ) that's why I want to use buck converter to maintain the output at 3.6v. please reply sir I don't know how to operate 3.6v led on 4.2v without loosing brightness, as the battery gets low. I'm looking for something who can output 3.6v constantly untill battery gets low from 4.2v to 3.6v so I led can't loose brightness until unless battery gets lower than 3.6v

@robojax 3 года назад

Hello, why you want to limit the current? if LED needs ONE watt, it will not take more. so first you should not limit it. But you have to provide 3.6V if it say 3.6V the Lithium Ion battery voltage is 3.7V when you measure it as 4.2V that is charge cut off voltage. so people don't call it 4.2V, rather it is called 3.7V so I believe and it is 1 cell. so your LED seems to work with 1 Cell and you don't need converter in between your power supply and LED. But if its, then if your LED needs 3.6V 1W, the current I=P÷V, P is power and I is current in Ampere so I=1W÷3.6V=0.27A or 270mA current. Do not use resistor as it wastes energy as heat. use this module and set the output to 3.6V and do not worry about current. Good luck.. Pease. Ahmad from Canada

@rctechmods8165 3 года назад

@@robojax thank you very much for your reply sir

@robojax 3 года назад

you are welcome.

@pavelpervomaysk 5 лет назад

12V -> 9V Use 22uH. 4.7uH to less.

@zaidqortas6221 4 года назад

thank you for sharing knowledge

@robojax 4 года назад

You are welcome. Thank you for not skipping the ads and keep watching them. This will help me a lot.

@dj_sorra8605 Год назад

Is good to 24v to 12v and 0.40mAh? For a cooler

@robojax Год назад

yes this is "step down" meaning output is always lower than input.

@josep.3364 4 года назад

I like the video, but I need to thumbs down the large board uses MP1584 but the small board uses MP2307 and efficiency, where are the efficiency tests?

@robojax 4 года назад

you are right. when I was going to make this video, I didn't expect anyone would watch it. My later videos on converts have efficiency and full details.

@zepante2795 3 года назад

I think, the smaller one is mp2307 not mp1584

@robojax 3 года назад

you may be right. Now I can't change it.

@omambarkar3091 3 года назад

Hey I want to power a raspberry pi from this and for that i have an input of 12v 1A and the output required is 5v 3A can this solve the problem??

@robojax 3 года назад

Hi, I did the test for voltage and current. it is you who decide if it works for you or not.

@omambarkar3091 3 года назад

@@robojax As you are expert in this topic I just want suggestion on it! Does it convert 12v 1A to 5v 2a?

@auzworld 3 года назад

could the voltage be changed with an ardunio ? if so could you let me know what i might solder?

@robojax 3 года назад

Yes it could . But you need to hardware and code to make it happen and to modify the module. I am not sure if you are going into that rout.

@ericjijan7798 Год назад

Very Usefull 💯♥

@darkcrox 3 года назад

i have adapter output 5v 1.5A can I use this buck to convert to 4.2v?

@robojax 3 года назад

Yes you can. But if you are planning to charge lithium battery, this does not control the current ans that is very important if you want to your battery to last longer. You need constant current which limits the current and subsequently reduces the voltage.

@rajatfq 4 года назад

My input 12v 7ah, mini 360, and it burst. how much input current should be?

@robojax 4 года назад

I did not understand the "mini 360" but to calculate the current (current is shown as I ) I = P÷V and P=IxV do this calculator in both output and input. Just keep in mind the the output always has about 10% less than the input.

@gotta91 3 года назад

6v to 3v? And if I use aa battery and Inout voltage decrease, the output voltage is fixed?

@camelCased 2 года назад

Yes, that's how most of the modern buck (and also boost) stabilizers work - they try to keep the output voltage constant, no matter what you feed in, down to their specified voltage limits. mp1584 should keep your output stable down to 4.5V of input.

@kkedmonton 6 лет назад

The sellers of these modules tell you that a heat sink is required for larger currents.

@robojax 6 лет назад

Yes. I have also mentioned that it should be cooled however possible.

@cameraman1234567890 4 года назад

Is there a way to make it into a constant current mode?

@robojax 4 года назад

no this module.

@ezequieladrianminniti6252 3 года назад

the smaller one is not mp1584, it is mp2307

@robojax 3 года назад

Thank you for letting us know.

@gurpreetmatharoo1829 6 лет назад

bro which buch converter is good to convert 12v car battery to 5volt 5amp DC -DC

@robojax 6 лет назад

This one. Any voltage up to 30V to 5V, 5A ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-OjDIUF7lebw.html

@tritile 3 года назад

Did you watch them on osciloscope? These modules are noisy as duck.

@robojax 3 года назад

No I did not. when I was testing them, I could not hear anything as I remember.

@Leonardo-yj3ks 5 лет назад

The power supply you are using is

@robojax 5 лет назад

voltage V and Current I (in ampere A) so you will always get less than what comes to the input. Example input 10V, current 1A 10x1=10W and output can never be more than 9.9W (assuming 90% efficiency). For example for 5V output can get get 9.9W/5V=1.98A. So calculated it with respect to power.

@PablumMcDump 3 года назад

@@robojax minor correction here -- if it's 90% efficient, it can provide 9W, or 1.8A @ 5V.

@shsftech3792 4 года назад

thank you!

@robojax 4 года назад

You're welcome!

@anwin85alon 2 месяца назад

Pm me can you to install do solar panel of charger :

@cspy0 5 лет назад

Can it step down 3.7v to 1.5v? Which mini step down buck can I use??

@robojax 5 лет назад

both can be used. But check the datasheet and it show you can get fro 0.8V up.

@MMaheshThakur 5 лет назад

you are best

@robojax 5 лет назад

So are you. Thanks.

@MMaheshThakur 5 лет назад

Can it charge my 1.5×2 aaa cell with 5.volt mobile charger. What is best module for charging aaa and aa cell with from usb mobile charger. Can I put heat sink on it

@robojax 5 лет назад

Yes you can if you have some way to turn it OFF when charging is done. You my use this module with any power supply to charge your battery ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-hacb6rNQDfc.html

@MMaheshThakur 5 лет назад

Robojax thanks

@mertbilgusi9850 3 года назад

hello, where did you buy the current load device?

@robojax 3 года назад

Hello, I just added links to different sources for the 10A electronic load.

@Shubham-po2tp 3 года назад

@@robojax Please tell me is those module useful for motor I want constant voltage speed for n20 micro gear motor Should I go for linear regulator or buck converter is suitable 2 using Motor Each is 12v 1amp

@RDCST 3 года назад

What's the consumption at 12V with no load?

@robojax 3 года назад

If have not mention it then it is 1ma or less than that.

@RDCST 3 года назад

@@robojax Thanks!

@orbita1 5 лет назад

do you think this module can handle: 24Vdc in 12-20Vdc out 1 - 1.5A draw ?

@robojax 5 лет назад

I believe I have answered your question in the video. Please watch it and don't escape.

@orbita1 5 лет назад

@@robojax I asked ten minutes in before you got there! Alas it seems this module is suitable. Thank you

@robojax 5 лет назад

LOL okay. you are welcome.

@orbita1 5 лет назад

@@robojax it seems one mistake in your testing is not using an oscilloscope to test noise. The smps at 24v in 20v out 1.5A draw has 2vpp noise. Totally unacceptable for some applications.

@ankansaha3260 3 года назад

Can I control DC motor speed by it ...??

@robojax 3 года назад

No. this is a fixed voltage. Most DC motor speed are controlled using PWM. Search my channel for PWM. Here is how search for a particular video in a Channel ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-OhkUceBWcHs.html

@IcemanTorre 6 лет назад

where you can buy the machine you use to test the regulators thanks

@robojax 6 лет назад

If you are in US or Canada here www.amazon.ca/dp/B07B466TGW and www.amazon.ca/dp/B07B3RWCFV if you elsewhere eBay would be better option.

@IcemanTorre 6 лет назад

Robojax I mean the device that has a fan and lcd screen

@ogomah 6 лет назад

you have a plan and list of components to make it or kits

@giuseppechiodi3356 5 лет назад

you can find it here: tinyurl.com/yd5mnzxg

@rourabkarar4584 3 года назад

Sir! Do you make giveaway. Because I can't find one in my local electronic shop. Those sold online are very expensive. Thanks in advance sir!

@robojax 3 года назад

Hello, I don't have them. I made video and after that God know where they are as they are very tiny.

@rourabkarar4584 3 года назад

🤣🤣🤣

@ZeroMass 3 года назад

they're $1 on eBay👀

@rourabkarar4584 3 года назад

@@ZeroMass calculate the shipping please. PIN- 700138

@Ajrocket 4 года назад

I have one but it is not working, no voltage is coming out.

@robojax 4 года назад

if wiring is correct, it must be dead.

@Ajrocket 4 года назад

@@robojax I will buy another, it costs 20 CZK = 0.75 cents maybe

@Ajrocket 4 года назад

@@robojax BTW I have exactly the same wiring as you.

@robojax 4 года назад

Good luck and stay safe.

@hexure9663 6 лет назад

cool

@electronmath8609 4 года назад

👍❤️👍

@robojax 4 года назад

Thanks.

@MMaheshThakur 5 лет назад

u did not tell difference in both.

@robojax 5 лет назад

it is the same chip. two module. current will not be affected.

@MMaheshThakur 5 лет назад

Robojax oh thanks u so much for reply . Then what is for 100 and R47 block there . What is it's meaning. Can I put heat sink on it. Can it charge my 1.2×2 aaa cell with 5.volt mobile charger. What is best module for charging aaa and aa cell with from usb mobile phone charger.

@robojax 5 лет назад

You are welcome. There are 100s but I have not tested any so far. So can't suggest.