Testing $300 Amazon Supercharger: Will It Blow?? 

I like these low low budget experiments especially when they actually work out.

I think this car would be a perfect candidate for a rebuilt junkyard M90 supercharger.

The Aisin AMR supercharger rotors aren't plastic, they are Teflon coated. The same applies to the Toyota SC12 & SC14, they are Teflon coated. Spinning them too fast, generates a lot of heat - which causes the Teflon to delaminate. The supercharger you've installed is a Toyota sc14 which displaces the same as an Eaton M90. Try to keep the SC14 under 15,000 rpm and it won't delaminate. The biggest upgrade to a supercharged engine is to install a set of headers. For a supercharged engine the primary pipe size should to two sizes about what is normally used for N\A - 1.75 inch primary pipes into a single collector should do the trick. The supercharger should be governed - Toyota used these on the 1G-GZE and the throttle body was in front of the supercharger, the ducting then ran through an intercooler before entering the engine. Of course its your car, so do as you please. This is just a bit of information for you to gain some insight as to what you have bought.

I'm definetly not an expert with superchargers but maybe putting an intercooler would be a good idea, main reason not to cool the air but to filter out the plastic pieces in case something bad happens. Love theese budget builds tho

30 seconds in and I can already tell this channel is going to BLOW up! Subscribed

Been eagerly awaiting this video!

This is awesome I can’t wait for part 2! Definitely subscribing

Definitely favorite new channel you guys rock keep it up you guys don't get the credit you deserve twin turbo LETS GO

Skip to the last 30 seconds of the video to see

how do yall only have 7k subs!! this is great content!

An M90 supercharger used is super cheap and easy to find on marketplace or even ebay. MUCH more reliable and likely less than the $300 you spent! Best of luck tho!

“While I am crazy, I am not insane.”😂 Same 💩 different day over here too guys💀

Put an intercooler on that so it catches the fragments if the rotors explodes and also dump valve in pressure side is recommented so it dont cause too much pressure when coming off the throttle, done that on volvo engine before.

Well it makes all the right sounds, good luck with the next steps!!!😎

From a fist too two fingers sound like an upgrade

what about putting a screen between the supercharger and the intake so in case the fins shatter it won't mess up the motor.

Get some stainless steel wire mesh and put between the supercharger and the intake to help keep the plastic from going into the engine.

Yoooo that’s RAD and I’m stoked to add mine now 🎉🎉

Started watching thinking you had hundreds of thousands of subscribes not 5k! Keep up the good work!

The most scuffed supercharged Miata setup. I love it 🤣

Car guy version of Mark Weins

Raceland is the best bang for the buck. I put a full set on my XB and it corners like a dream.

This is the first video iv seen from this guy ..dose anyone else get mark weins vibes off this dude it like mark started a car channel

Put a screen on the out put side. To prevent the problem from last attempt

Look forward to seeing the video y’all made up in Switzerland today. It was nice meeting y’all guys 🤙🏼

I cant believe you guys only have 5k subs got mine so i can say i was there when you touch 1million. Also i love long videos like VGG PBG and junkyard diggs put out. Btw.

Can't wait to see the next one

This is a beast ngl

Awesome thanks 👍

This video blew up for yall please make more of these

Those raceland coils are really good I ran them on my g35 drift build they were perfect

Just add like a turbo filter net for u can catch the plastic pieces before it go in the engine just in case

K, first video for me on this channel and I am here for it, let’s goooooo

It’s like those middle eastern videos where they replicate, then forge the SC housing out of molten aluminum, and probably 3D print the rotors. 🤦‍♂️ and you paid $300 for it. 😂 Oh, forgot about the sand blasting to make it look nice. They have lots of that there 🤣

Here is a simple rule of thumb. The more friction the more heat, heat kills parts and power.

Amazing to me they even bother with plastic of any type, the case casting makes me think they could manage the rotors also. Wonder the internal RPMs of it.

What would those plastic rotors you should decide to put in some kind of fine mesh net behind them so if they break they get caught before they get into the engine

A few years ago I installed a supercharger from a Mercedes compressor in a Miata 1.6 it made 165 hp in the dyno..

Amazons always got your back😂

Wild build🤣

On my Dyers 671 supercharger i was told to run my belt a bit loose. Turns out that's correct as the belt, counterintuitively, tightens up as it heats up. Running too snug it then tightens up enough to put tension on crank pulley which in turn can cause main bearings to wear more heavily leading to early engine failure.... At least on a street driven ride like my pink '64 Corvette ProStreeter. rick in Tennessee.

The ultimate drift car chassis would have open wheels or sculpted fenders so that the chassis center of gravity could be located below the center line of the axles like in Formula One or Indianapolis Speedway cars with narrower tires that are made to have reduced traction obviously there would no way possible to flip such a car unless it impacted and object and flipped. Also no body roll occurs when the center of gravity is inline with the center line of the axles or below it so no need for better roll bars ect...

9:42... The perfect, "that's what she said."

Right next to Aurora central is crazy

I knew I’d seen you somewhere before… So this is what Trevor is upto since he move out of Sunnyvale, hope Corey is keeping well. BAAAAAAAAM.

Id put a mesh screen between intake pipe.. almost like the screen for turbos thst dudes put when they run no air filter

Aye man I don’t know why you getting so much hate but keep up the good work 👍🏽🔥

YOU KNOW HOW TOXIC ZIP TIES ARE AND DUDE HAS ONE HANGING OUT HIS MOUTH LIKE IT'S A PIECE OF HAY GRASS......

Man I can't wait till camera manufacturers come out with some sort of image stabilization.

finally sc14 supercharger

i love the content

The pulley on the blower is bigger than the balancer pulley, lol..that’s so funny..

Interesting build thats for sure 😂

Why did I glance at your thumbnail and think Mark Weins became a mechanic lol

whoop! Dunno how I ran across this channel, but TOO FUN! Makes me wanna grab one of my worn out 302's and stuff a supercharger on it just to "see" .. Should Be fun ..

10:40 is when it starts.

Raceland coilovers and epic in the same sentence. Not something i ever thought id hear

This must be a baby Cleetus channel. That’s OG Leroy’s over seas cousin Lēi luō yī🤣🤣 that was too funny🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣

Maybe install a mesh screen in the line to prevent the FOD from entering the engine?

Don't forget to put window screen on the side that pushes the air in the motor so if it does fall apart your not getting pieces in the engine

It's always the coils 😊

Sc14 rotors are "Teflon" coated. Perfectly good superchargers

I doubt it puts out enough for your engine but its fun to watch and I will probably do a similar mod to my Kubota diesel.

This is probably going to Rob More power than it makes not to mention an air restriction. It would be a good idea to take the charge pipe off where it connects to the charger and make sure that the holes are the same size and if not poured it out also probably wouldn't be a bad idea to Port the exhaust side either to match the diameter of the exhaust so you're not creating a air restriction. Also probably be a good idea to add a screen or a intercooler so if it does fly apart it doesn't go straight into the engine and you need a boost gauge you can always change the pulley size to make more boost

Wtf half the charger is bolted to the engine that moves , and half to the solid frame rail.😂

im always down to watch a dumpster fire, not sure why the algorithm put this in my feed but take my sub, cant wait to see it melt

That blower sounded scary dangerous, it’s going to blow up with in the first 10 hrs of run time..

Given what happened last time, I would have though you two would have at least had the foresight to go to walmart or something and get some window screen to make an intake protector screen in one of the couplers before the throttle body.

I put a amr500 and a 46mm Mikuni on my wifes 84 subaru GL. I loved it right up until it tore up all the front end drive components (ate the hubs and destroyed a shaft). It originally only had 76hp and the carb and SC are both rated to 150hp. Honestly I'm not sure what its making but the bottom end grunt is fantastic. Now I just have to retrofit modern knuckles and suspension into the old girl to get it back on the road.

HEY. HEY. How dare you. If you are gonna work with angles and dangles you cant forget about mr bojangles! 😂

It looks like a direct replica of the Toyota blowers from the late 80's so it should be good for something

Im curious. When r u guys gonna finish it to see if it gets results?

Do you need fuel injected in blower feed air to cool and lube the rotors??

A bypass valve will relieve boost when TB closes.

I have one on my lawnmower...cuts the yard in half the time...damn octane boost tho...

Just subscribed

You should take out the plastic parts and 3D print the parts in metal to see if that makes it better.

I'd take it apart, and have the plastic pieces machined from metal. Then reassemble using the metal replacement parts. Fingers crossed 😅

Maybe you should put some kind of a screen between the supercharger and the intake for the engine that way any plastic does break off it gets caught in the screen rather than in a motor

Damn thing sounds like my riding mower!

You should put in a screen to catch the broken plastic.

the cameraman vehicle is hilarious

That's no supercharger, it's a kazoo. Kazoo Racing was born this day.

Went from a fist to not even two fingers fitting. I'll leave this right here.

Definitely need a c230 kompressor on it

the belt should only be able to push in 1in with slack

I really don't think the guy with the pink leopard print with blue glasses as wrenching

by the sound of the pitch it need a smaller pully x5

Plastic next to exhaust!?! GL

Watermeth injection before supercharger so to keep it lubed and cool

Whack you didn’t even plumb it up….you proved it can spin that’s about it 😂

Mercedes compressor electric superchargers work pretty good. I mean it worked on the old mr2

dang the one guy is a total Eeyore personality all is doom and gloom

When are you going to post next video of this.

so how is it working properly when its not pushing the air into the motor only towards the firewall?

I'd put a screen between the supercharger and throttle body.

Put a heavy screen in the intake on case of disaster...

add the supercharger that is in the toyota previa. They are around 300 on ebay and last a long time.

Why not make shift a filter to put in the intake side? So if it blows up again

What I think might of happened, was welding on the motor without unplugging the coilpack and module it fried it