The MOST affordable & RECHARGEABLE!! power brick for your pedalboard -Joyo JP-05 Power Supply 5 

@@BandOnABudgetNZ all cable 8 output i tested and not isolated :D buddy , but im happy with this product, just add another protection something like hum/noise etc,with ZGP Joyo Blocker/isolated , u can check

It is isolated from mains power noise because you don't have to plug into mains... This is a godsend for venues with dirty power.

@@BandOnABudgetNZ hi thanks! THe wall wart is factory , and it says... INPUT: 120V AC 60Hz 8W -- OUTPUT: 40V DC 100mA

@@BandOnABudgetNZ Hey, thanks for looking into that for me. wow awesome effort man!

If you run into mounting issues, I sometimes use Velcro tape to secure it a bit more while also using mounting plates. If you feel up for it, you could drill a few holes into the pedal board where the LED indicators would normally be so you can see it. A bit of DIY modding for your pedal board

@@BandOnABudgetNZ Awesome, thanks man. I’m thinking I’ll get one, are you still happy with yours? Do you recommend anything else?

@@BandOnABudgetNZ Thanks for your advice and input ✌️

Thanks, I haven't used any pedals with it yet, I literally just took it out the box and started charging it when i got it. Soon as it started charging there was a flashing green light, i left it for 2 hours and it was still flashing green. I'll give it another hour charge and see if it stops flashing. Thanks for replying @@BandOnABudgetNZ

I'm not too sure however from past experiences I have use a combination of Velcro strips and cable ties to mount power supplies under various pedal boards. I usually only to this if the power supply I'm working with doesn't fit in the pedalboard brackets. I've even gone as far as drilling small screw holes into the pedal board and making my own mounting plates, or even just small enough holes to loop cable ties thru and then around the power supply to hold it in place.

Yes! If the battery gets depleted, and you plug in the AC, it will work…and recharge the battery simultaneously. I swear by this thing.

@@BandOnABudgetNZ Ok, now I understand, I think I had misunderstood you. What you say in the video is that in one of the 500mA outputs you can connect a daisy chain and in this connect several pedals that together do not exceed 500mA right? Taking into account that it is also an isolated power supply, I think I will decide to buy it. Thank you very much friend!

You could always use 1 300mA + 1 100mA pedal for each 500mA output with a daisy chain so you could save space if wanted to c:

I own two of these. I haven't noticed any noise on my bass pedal rig. Seems to run pretty quiet. On my guitar rig, there was a very very faint hiss/hum however it was hard to tell if that was actually the power supply or other interference. I only heard it when practicing at home when the whole room is silent and if the volume on my amp or headphones was up quite loud. At a gig, I can never hear it, the ambient noise of the room and the crowd masks it so much that you could never tell and I've never had any issue live. Soundie never had any issues either, says my signal came through pretty clean.

Yes

@@BandOnABudgetNZ i have my bcb60 for 10yrs now and im using it almost like regularly..wall adapter and daisy chain is still working but the hum is loud when i use a guitar with passive pickup..

@@BandOnABudgetNZ its a humbucker(EMGHZ)..i just tried a new cable for the guitar, its a lot less noise, i think its acceptable now..i forgot to tell you that the noise only comes when i turn on my distortion(revv g3) on..

@Band On A Budget its at the front..i need to replace my old guitar cable, its the one causing the loud hum..

According to their website yes you can: www.joyoaudio.com/product/94.html The battery has a 4400mAh capacity.

Cool, I plan to use it for busking, so I thought I'd check

I don't think so never tried and I'm not too familiar with that Marshall amp. Best to stick to pedals for this power brick

probably take it as carryon. No different than carrying a phone or a portable power bank

@@BandOnABudgetNZ thank you for your answer! well that means, I can not see if the battery is really full charged. is it right?

oh just recognized: blinking stopped! all bugs fixed. Thanks for your review anyway, very nice job!

I'd say just pedals

If I had setup with 10 pedals or more id consider using the 529i just because the outputs have a higher current of 500mA and 300mA to choose from where as the Joyo has a couple of 500mA but the rest are 100mA. For example If a few pedals only require 100mA or less you could daisy chain up to 3 of them from the 300mA output (preferably analog pedals and save the digital pedals for the 500mA)

Ive got an HX stomp and a NUX B8 wireless system both of which require 500ma other than those two i have an scf gold stereo chorus that draws 150ma otherwise the rest are under 100.. should be fine running two Joyo units together right?

@@hiriwarikihana1283 It should be ok just make sure you dont daisy chain the two power supply. If in doubt its best to just use one output per pedal to ensure it has sufficient current to power the pedal.

I use it to power 11 pedals, 9 analog and 2 digital (POG and space echo) and it works great. My band I usually play 1 hour set but can last around 3+ hours continuous in my experience. It hasn't let me down yet and i've had it since 2020. Edit: Also worth noting that I daisy chain my drives and compressor!

There should be almost no noise with this unit. Its basically one big battery. Great unit, I have it for couple of years now. Just used it on the the gig for small pedal board. No need to check for outlets. Fantastic.

are outputs isolated? have you noticed any hum plugging digital and analog into this one?

@@LukeryaPereprygova not isolated, but also not plugged into mains power so not susceptible to 60 cycle hum. I hear some noise through headphones when I'm not plugged into an amp or PA, but I've seen a lot of people say that the IR200 headphone out is noisy, most likely part of the reason it has an earth ground screw on it that I haven't used. It isn't hum it's some kind of digital static

According to the label and manual it is isolated... however I dont think it is fully. I know there layout and design shows some of the outputs positioned into groups so I wonder if the title isolated is kind of misleading to those groups only. I have used this for so long now and pretty happy with the sound. Sometimes I may hear some noise but that's mainly due to one setup I had where there was a lot of high gain and volume. But for the most part its pretty quiet. Just be sure to run your digital FX separate to your analog FX within the groups on the power supply. In short, you get what you pay for, in this case I feel like I lucked out and got a pretty reasonable priced power supply that not only provides power for my pedals but also has a USB charge port AND built in battery to run on its own charge. If you are worried about noise then definitely go for a more expensive one with the trade off being possibly less outputs, no USB and no recharge capability. Is there a way you can take your pedalboard rig into a music store and try our the power supply?

It's not isolated and was noisy as hell with some of my pedals in the chain, but I added a couple of Joyo ZGP isolators to my noisier digital pedals and now no noise issues at all.