Thank you for watching! More videos about the Modular Cabinet System: • Modular Cabinet System More info and plans for the Modular Cabinet System: jerswoodshop.com/cabinet-system/ Patreon: / jerschmidt
I only removed one wall, and cutting the slots deeper only on one side would have made the drawers visibly off-center. Removing and re-cutting both walls would have been double the work.
If you cut off the walls you're removing wood so you need to add fillers anyways! Sanding 16 dadoes inside the assembled cabinet.... is a hell of a lot of work.
Adding the thicker filler strips was so much easier because the saw kerf alone was going to require filler strips anyway on top of the work to re-cut the 8 dados per side. Jer definitely did it the easier way plus accented his “mistake” with the walnut filler strips.
I am new to your channel and I am overwhelmed at your seemingly innate grasp of the laws of physics, your effortless and complex analytical ability, precision planning and skillful execution of your work. You are a very talented young man and I look forward to following your channel videos.
Excellent video - learning how to fix mistakes is a great skill. Extra likes for being honest enough to admit you thought you had the measurements memorized. And didn't.
Another obstacle...another proportional, well-thought out and creative solution! Impressive and inspirational as always my friend. Kudos and thank you for another great video.
I think Modular Cabinet System might be my favourite youtube series. Everything is just so precise and well thought out! Even this video about a mistake is just making me happy about how tidily you fixed it! And the walnut scar looks very fashionable in my opinion. It's subtle, but if you're looking for it, it's right there waiting. Very cool.
Nice fix, I think it looks great with its "scar!" I half expected you to make some sort of tool like a router plane that would fit the tight space, and not have to disassemble at all. But I'm still glad to have another video and more Jer ingenuity!
Thanks for sharing this learn by mistake topic. I think that about every project has something that does not fly exactly as it should have. Being able to recover without restarting from scratch is as much a key quality as being able to invent something. Not sure how I’d have dealt with that one though. I think you indeed took the fastest route to resolution.
Jer, Hello Again. I must say, you are that ten percent more clever than the normal person and you have the precision to match the attempt to remedy. Will you accept that as a compliment?
Above was my comment sometime back, but RU-vid changed my ID for logging in to the one on this comment and I can't edit the original post. I'm going to update and correct the comment by saying you are well over the 10 percent that I jokingly put on originally. Sorry for the DIG and demotion at the time!
Love the fix. I think we all goof on stuff like that and kick ourselves after the fact but fixing the issue and making it stand out is a great reminder. Also money shot on the clear coat going on the walnut.
I like the fix as a trim feature it adds a cool detail to the design and overall will not weaken the structure any..good stuff You could easilt put this into both sides on a future from scratch build by simply altering the dimension to fit the fillet. You could even use different coloured fillets depending on what type of tools are to be stored in it ..if you like that sort of thing. thanks for sharing
I made this mistake when building you plans before…used a router, guide and flush trim but to get slot to right depth and used a chisel to clear out the back that the router wouldn’t reach. Took a lot of time, but looks comparable to this time-wise
I think the filler looks great. You should add them to the next ones you do, Its a feature not a bug... Maybe use different wood types on different draw boxes, Just liking the contrast. Love you work. 😀
The mini router planes may have solved this problem. Especially when you can mount the blade off the back to reach into the back of cabinet. Lee Valley Veritas makes two different small router planes. Love the walnut strips.
That walnut does look very nice and clean. 👍 Maybe a handheld router plane could have let you deepen those grooves to save cutting it apart? Million ways to skin a cat though I guess 🙂
Well, now you have to make a butcher block version with exotic wood for use as an end-table in a home. Would make a great video and expand your audience into an existing (and massive) RU-vid market. #EveryDefectGetsRespect
I enjoyed watching you work through a problem, your precision and attention to detail are master class. A customer design, fab, and install video would be a great vid. A J. Schmidt designed workshop!
After I built and finished six caucuses from 3/4” baltic birch, and was about to build drawers… I realized that nobody sells 3/8” baltic birch in my area. So I had to order that online for my drawer bottoms. Just saying... Great plans, great stuff!
Really well done, Jer! They turned out great! 😃 You should measure the plywood you used in those and compare against the older ones... I could bet they aren't the same. That's what probably messed up with your build. Anyway, stay safe there with your family! 🖖😊
3:44 I dont understand why you didnt cut the slots deeper. On the tablesaw i think thats a lot easier than glueing filler on. I just saw you answer to @AronGreen Thanks
Interesting correction. I'm lazy and would have accepted having a couple of non-interchangeable modules. But I agree with AronGreen - why not cut off the side(s), recut the dados, and use a spacer to keep the outside width consistent? Good video.
I am curious as to why you didn't just trim 1/2 mm off the bottom projection on each side. This would appear to have negligible impact on the drawer projections and the trimmed drawer bottoms would remain compatible with the prior frames. It would appear to take only minutes to run the drawers through the table saw trimming each side. The overall drawer width would remain unchanged so that the drawers would remain centered in the opening. Am I missing something about that solution?
Wouldn't it have been possible to just route the slots a little deeper? Just route each half the missing depth without taking it apart at all. Or for that matter since it's less than 1mm, just sand it or rasp it? Or just cut the drawer 1mm on one side? I dunno, seems like all of these things are much easier than what ended up happening. Maybe I'm not understanding though
A router won’t fit in the bottom two slots or the top one without disassembling the cabinet, and it won’t reach the back of any of them. I tried sanding them, but that was on track to take way longer than this did. And I addressed why I can’t cut the drawers narrower in the video.
That would still require me to disassemble the cabinet because there’s not enough room to use the plane (especially not for the bottom slot). So then that would just be extra work with no real benefit over how I did it.
Hey Jer, nice work as always. One question I had was with the pre drilled holes. The walnut hides and obscures the lower hole, if I’m not mistaken, so did you just rely on the screw penetrating the walnut and then “finding” its way into the lower portion of the original pre drill, thus aligning things? I was just curious. Thanks!
Yeah, I figured once it found that lower hole, it would mash itself sideways in the walnut enough to line up. It seemed to work well enough. And it's easy to start it close enough that it finds that hole, because I can line up the sides flush enough by eye/feel.
Personnaly my fix would have been simpler, quicker and invisible to the naked or clothed eye. I would have made new drawers, so they fit and simply not exchange drawers around my shop. (I would have kept the old drawer parts for new drawers as they were the correct dimension)
I thought about that! It would have been a good technique I think, but I decided it wasn't worth buying & modding a tool rather than fixing it with what i already have.
@@tcarney57 Absolutely, that's pretty much how I see it. Works for me! And, incidentally, making a fundamental mistake such that something can't fit, and the 'fix' leaves the external dimension incorrect I would not consider a minor flaw.
@@tcarney57 I am happy for you that you are content to live with your mistakes. If it brings you peace my friend, that is a good thing. I still take pride in my work.
I used to think this way, but I’m starting to realize that “taking pride in my [perfect] work” is/was just a way to protect my fragile ego. You’ll always be learning and growing, and I think it’s much better to look back on past projects and be reminded “that’s the project that taught me x”, rather than “that’s the project that the younger, cockier version of me thought was perfect”.
This is just grossly unacceptable.. I'm seriously disappointed..since when has Jer allowed 0.5mm out of tolerance to slip passed his Quality Control..and then even worse to then say 1mm over tolerance is okay ? Someone needs to do a welfare check on Jer if that's even Jer at all..something is Hinky about this Big time..
