Thickness Planer Tune Up and Maintenance

Подписаться 551 тыс.

Просмотров 176 тыс.

50% 1

Get the Katz-Moses Magnetic Dovetail Jig here: lddy.no/stiz
In this woodworking tool video we do a tune up our Thickness Planer and go over basic maintenance to get your Thickness Planer working tip top. Whether you bought it new or used these basic techniques work great for getting your tool in top working order. Thanks for watching! Please like, comment and subscribe. Cheers!
----
Buy the Katz-Moses Dovetail Jig: lddy.no/stiz
I have Walnut Slabs for sale: lddy.no/stj0
Buy The Katz-Moses Stop Block: lddy.no/stiz
The Katz-Moses Woodworking Apron: lddy.no/stir
BitsBits is the BEST place to buy router bits: bit.ly/BitsBits USE CODE JKATZMOSES15 for 15% off
Total Boat Epoxy: bit.ly/2I3Q8m4 10% Discount code JKATZMO
----
Essential Woodworking Skills Playlist: • Essential Woodworking ...
----
Woodworking Joint of the Week Playlist: • Woodworking Joint of t...
----
Tool Tune Up Thursday Playlist: • Tool Tune Up Thursday
----
Check me out on social media:
jkatzmoses
www.Facebook.com/katzmoseswoodworking
patreon.com/katzmoseswoodworking
/ katzmoseswoodworkingshop
----
Tools I love:
The Katz-Moses Woodworking Apron: lddy.no/stir
My Favorite Dozuki Saw: lddy.no/stit
My Favorite Ryoba Saw: lddy.no/stiv
New Flush Trim Saw: lddy.no/stix
Razor Saw: amzn.to/2nm0FzG
Marking Gauge: amzn.to/2nlXLuQ
Marking Knife: amzn.to/2nm39Ok
Stanley Sweetheart Chisels: amzn.to/2mVMTkF
Knew Concepts Fret Saw: amzn.to/2FUDbYZ
Dewalt Planer Package: amzn.to/2thEf6O
Forrest 10” Combo Blade: amzn.to/2Fdaee3
Festool Tape Measure: amzn.to/2oS3cjD
Starrett 6” Combination Square: amzn.to/2oP3dVw
Woodstock 3 in 1 Shoulder Plane: amzn.to/2FgAS1A
Stanley Low Angle Jack Plane: amzn.to/2oV4I4O
Dewaxed Shellac Flakes: amzn.to/2FeqqYh
Abalone Inlay :amzn.to/2rjMTxe
Abalone Inlay Alternate: goo.gl/DHonFy
5 Minute Epoxy: amzn.to/2FijsSa
Triton 3 ¼ hp Router (with built in lift and edge guide incl): amzn.to/2LBw3Go
Kreg Router Plate: amzn.to/2A7oVNC
Triton Bushing Set: amzn.to/2A7pSpa
Bosch 1 HP Colt Router Set With Fixed and Plunge Base: amzn.to/2mHP1wY
Bosch Edge Guide: amzn.to/2uRRKs2
Bosch Bushings Set: amzn.to/2JUNRYb
Centering Cone: amzn.to/2OjgOAf
¼” Inexpensive Router Bit Set: amzn.to/2JUPrJB
½” Inexpensive router Bit Set: amzn.to/2Abyhrq
Whiteside ¼” shank Spiral Upcut Bit ⅛”: amzn.to/2LDw6S1
Whiteside ¼” Shank Spiral Upcut Bit 1/4”: amzn.to/2uNanxA
SUPER MEGA FLUSH TRIM BIT ½” Shank: amzn.to/2LyH1wr
SUPER MEGA FLUSH TRIM BIT 1/4” Shank: amzn.to/2JWMFDx
45 Degree Bit I Like: amzn.to/2JRNNII
Whiteside Inlay Kit I like: amzn.to/2JV0DWp
Flush Trim Bit I Use All The Time for smaller applications: amzn.to/2uPrvCC
Avid CNCs of all shapes and sizes: bit.ly/3cdKdqA
Bescutter Laser (awesome c02 and fiber lasers) Website: bit.ly/bescutter
----
Camera Gear:
Lumix GH5-s and main lens: amzn.to/2J49F7m
30mm Macro Lens: amzn.to/2GJXtTT
15mm Lens: amzn.to/2NafUox
50mm Lens I use for product shots: amzn.to/2mehs5y
Microphone: amzn.to/2IGjKIa
Lav Microphone: amzn.to/2Nb8SzY
Gimbal: amzn.to/2s9ZV0F
2nd CAMERA Canon 70d: amzn.to/2FiCEDq
Tripod: amzn.to/2HasNvK
Slider: amzn.to/2oNucSd
24MM Wide Angle/Macro Lens: amzn.to/2oSzzjh
50MM f/1.8 for those tight shots: amzn.to/2tpAoVm
10-18mm Lens for the wide shots: amzn.to/2FZrhNM Axiom CNC (so awesome!): bit.ly/2J9RnPX

Хобби

Опубликовано:

29 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 162

@katzmosestools 5 лет назад

Great drying lubricant for Tool Tune Ups: Glidecoat Drying Woodworking Tool Lubricant: amzn.to/2Lys3aY I Love This Paste Wax: @t @t

@glennryzebol4472 4 года назад

Hey Jon, thanks for this video. I might be looking for a new planer soon and I see this one everywhere and figure it`s a good sign as to quality. Would you reccomend this unit? Can it handle moderate use? Thanks again

@dlmad4561 2 месяца назад

Hey brother ! so today my 735 arrived as my 734 just made the Montana border on it's way to Helena and its new home. My best friend wanted it and I wanted to up grade and also went with the helico cutter blades. I ran in after getting it mounted on the stand that is made to fit both. Then I came in a nd rewatched your set up video and went to set it all up. I spent the last 30 years as a union perscion Millwright so I had a clue. After set up it took on some hickory and some quilted maple. It did great . My helico will arrive in a week or so and I will go back to you for install. Love your video's and I can hear your voice very well unlike others. Stay cool, you be the Man !!!

@ScottSpeedPro Год назад

Dewalt should use this as their official maintenance video, great info across the board. I just unpacked my 735x and this is priceless moving forward.

@msk3905 Месяц назад

I’ve been using ceramic auto exterior protectant on my metal surfaces and it has been working better than the paste wax I was using before

@lockcitywoodworks 5 лет назад

I want a planer so bad. Someday. Congrats on the little girl, Jonathan. You're gonna love dad life.

@mattbram8993 3 года назад

Black Friday sale on Amazon for this model, $499 :)

@gnarthdarkanen7464 5 лет назад

GREAT video!!! I'm certainly glad SOMEBODY is putting out a few tips on opening up equipment and cleaning it out! Thanks... As a technician who often "services the unserviceable", I can attest to the very VERY high percentage of tools (among other things) that are discarded over a "janitorial issue". AND it's nice to see the inside of something before I've had to dive into one of my own. (lolz) ;o)

@scottlward1 5 лет назад

Best of luck with the new baby!! Hoping all goes well. Thanks for the videos, love watching your shop develop and all the helpful hints and tips.

@WindRidgeWoodCrafts 5 лет назад

Great series, Jonathan. Thanks for taking the time to create it.

@markhunt6177 5 лет назад

Just bought a new planner. Have to get it calibrated. Perfect timing for this video! thank you.

@rhihodag9873 5 лет назад

Love this series! You are absolutely correct that we should give all of our equipment some periodic, regular TLC. We oftentimes neglect to 'tune' and clean each and every piece in our shop. The investment in time pays off 10-Fold! Thanks for all the GREAT tips!

@bryangittings4197 5 лет назад

Loving the turn up thursday. After seeing you tune your table saw I went and did mine wow much better same with the chop saw. Saturday the planer hahah cant wait to see what's next

@robertshelton3796 3 года назад

Just bought one of these used. For the Dewalt in particular you can set the feed speed lever in the middle (essentially neutral) and rotate the feed rollers by hand.

@MrJohnnyboyrebel 3 года назад

Wonderful video! Just spent a very fruitful hour tuning up my DW735.

@drewfalkenburg6808 5 лет назад

Pro tip: Many levels have magnetic strips. Lay one on each side of the planer bed extending over whichever feed you are adjusting. Levels will hold the feed for you while you tighten!

@Supreme.Shinobi Год назад

i just did it this way after struggling for 30 minutes. WAY EASIER. thanks for the tip!

@gylesdias2900 Год назад

Newbie watching this, please could you explain what you mean a bit more? struggling to get this level and not sure how to use these magnetic level strips

@Supreme.Shinobi Год назад

@@gylesdias2900 loosen the 4 screws, place level across the planer bed magnet side down ensuring the magnetic part is touching the bed and out/infeed table. tighten screws, repeat on opposite side. I ended up adding a bit of an angle to both sides but same process.

@AKdesignsandhardwoods 5 лет назад

I just so happen to be doing this exact thing and opens my phone to your upload. Perfect.

@lancem5965 5 лет назад

Love these tune up Thursdays

@JkCanvas 5 лет назад

Another awesome tool tune up Thursday.

@BobChristenson51 5 лет назад

The blades for the 735 are NOT made be sharpened per manufacturer. You may be able to hone them but they are indexed to the cutter head so the height adjustments changes slightly. 2 things will affect planer performance when you try to sharpen the knives. Additionally, if the knives are not sharpened exactly the same amount the quality of the surface will be compromised. Washboard and increased snipe will result. Good video.

@AlphaNerd132 4 года назад

I'm drooling over all the upgrades he applied to that thing. I have the same model but base.

@BradsWorkbench 5 лет назад

Thanks for making this. I have the slanted board issue. I was able to minimize it but haven’t been able to eliminate it. I do flip the board but have had times I lose track of which side is the high side lol. But at least I know now not to drive myself crazy trying to get it perfect

@gerraldhead8317 2 года назад

A big THANK YOU for this video. It shows me the issues I have and how to fix it.

@anthonyhenley2480 5 лет назад

I love these tune-up videos, not just because of their top-shelf quality but I know that they will be here for reference when I do need to tune up.

@MarioG2912 3 года назад

AAAAHHH! Wish I would have seen this video earlier. I went from changing blades, cleaning rollers, waxing table, heating up my shop, thinking keyed gears were broken...the big problem was a misaligned infeed table. Just milled about 20BF of cherry like a boss. Thanks, man. Now I can finish building that moxon from your other video.

@wwscott7595 5 лет назад

Hullo young man. You and your wife are now starting a new phase of your life together with the arrival of a little girl. The lunch box thicknessers we have over here are more like timber mincer's. We use mostly a machine that is a combined planer (jointer) and a thicknesser underneath. Then again we use metric and you use feet and inches. You sent a man to the moon with a pencil, paper and using feet and inches (a rocket as well) Love to all the family BIG GUY.

@cameramaam 4 года назад

Thanks for this very useful and informative video. First planer, I want to do it all right!

@mvred100 4 года назад

Great video, Jonathan.

@jeffforbes3772 5 лет назад

Great tips sir. Thanks for posting.

@silver-hy6mi 5 лет назад

Great video and advice, I hope all goes well with your new Bub!🍼

@multidinero 5 лет назад

Congrats on the little one, John!

@TheTranq 5 лет назад

Great video. My planer just started leaving a groove and I'm happy to hear that the Dewalts have double sided blade

@katzmosestools 5 лет назад

The best ever!

@tomblount5635 3 года назад

I just enjoy watching these vids about adjusting the infeed and out feed shelves. It doesn't dawn on these geniuses that the planer comes set up from the factory. Leveling these shelves only enhances the snipe. The planer has two rollers. If you are having snipe. Simply lift slightly up on the out feed side of the board as it comes off the front roller and this will greatly lesson the snipe. If you do what this "expert" suggests. You will definitely improve your SNIPE. Guaranteed. Leave it alone and enjoy planing

@JordanWoodwerx 5 лет назад

Great tip, thanks man!!

@lPaulSaltzman 4 года назад

THANK YOU, THANK YOU AND ANOTHER THANK YOU. I am waiting on a new belt and a set of sprockets for my DW 735. Even though the belt does not seem worn and the sprockets are fine. The problem I am trying to correct is the feed rollers are not doing their job. Now I watching you, and your chain on the opposite side that I am on and then I hit me like a ton of bricks, My problem is on this side. So I jump up, remove the three screws and find the BROKEN SPROCKETS. Thank you, Jonathan, you are the only one that shows this side when cleaning the planner.

@katzmosestools 4 года назад

My pleasure bud!

@weedyganzalays 3 года назад

Fantastic video dude thank you so much!

@robertmcevoy24 5 лет назад

Thanks this will be very helpful

@bocchieri 5 лет назад

congrats on the newborn!! fatherhood is a blast

@FredMcIntyre 5 лет назад

Thanks for the info! 😃👍🏻👊🏻

@joshmohi9298 5 лет назад

congrats on the baby,thanks for the info.

@bear1277 5 лет назад

On the 735 I don't think the infeed and outfeed tables are supposed to be exactly level. They're supposed to be level where it meets the main planer bed, but they're supposed to incline the further out you get. This is supposed to simulate the tilting of the board trick that further helps to reduce (eliminate?) snipe. I definitely noticed a difference in snipe after making this adjustment on mine.

@swooopg 4 года назад

Good idea! I’m definitely gonna try that...my planer leaves really bad snipe. I made the planer sled and it works well but it’s a pain to use.

@threesonsrestorations4043 2 года назад

You are correct! I'm surprised JKM hasn't corrected his video with this information or acknowledged it in the description. The tables came set this way from the factory for a reason!

@halfbeardsilvertongue5129 Год назад

Hmmmm... I'm glad I read this comment before I "tuned" my brand new planer. Think I'll watch a few more videos before I jump into the setup. Thanks for the video, JKM, and thanks for the comment, @bear1277.

@msk3905 Месяц назад

No matter how i adjusted my out/in feeds i get snipe with this planer…disappointing to say the least. I have only found one way to eliminate snipe, use a long straight board resting on feed arms but then my height gauge is useless without doing math.

@alwayssearching1882 4 месяца назад

I love this upload. My new Harbor Freight Baur planer has horrible snipe right out of the box. I watched that video of the one piece you mentioned someone else made but I am going to try and adjust my flip tables prior to building a unit. Thanks for the info.

@msk3905 Месяц назад

So does this one even after playing with countless adjustment settings to the in/out feeds.

@BarrySumpter Год назад

Champion of Champions!

@snydercustomwoodwork 2 года назад

Another great video! If you could get a straight knife head for your jointer and show how to replace/ adjust your knives I think it would do really well.

@HikerNine 5 лет назад

I love you, man.

@LQ-gaming Год назад

ty boss! squeaky clean !!

@Whatthensayyou 5 лет назад

Now I feel like a someone who was able to ask a question at a presidential town hall, and get an answer!! Thanks for the tips, This is my most expensive tool in the garage and this weekend it will get the katz moses clean up :D ... Now just gotta order some more stickers lol

@katzmosestools 5 лет назад

Go get'em tiger!

@roberttravis6713 2 месяца назад

Remove the cover on the hand wheel side. The v belt pulley is held with a 24 mm nut. It is low profile and has neither a lock washer nor nylon lock. Inspect it. If it loosens (the machine vibrates a lot right?) the pulley will wobble the belt will melt and the pulley gets ruined. Oh you’ll definitely know this is beginning if the feed rollers are running but the cutter head isn’t.

@theriddler9963 4 года назад

Thanks for the very helpful video, you mentioned you would post a link for snipe attachment. I maybe overlooking it but could you point me to the video?

@Rossco242424 2 года назад

Quick question, thank you for the great video. Why not use glidecoat on the planer bed as well?

@thenext9537 Год назад

All I can say is take your in feed and out feed tables and angle them most of the way up! I got rid of snipe that way. Does it happen still? Yes, but with long stock, If you don't grab it at end and lift up a bit, when end goes past first roller, it will tilt UP into the blade and that last 2" or so will snipe. Also supporting it at an angle going in helps alot -I use a roller stand which angles things like a 1/8" to 1/4" as things enter the planer. When you get to final thickening, you'll want to know this. I've spent too many hours chasing snipe and thickness to give a crap anymore. I hate it, but when I get it right, so nice.

@kendelmage 4 года назад

Hi. I love your videos and find your method of explanation to be very clear and helpful. I have a question for you about my Dewalt 735 planer. I bought it used and I didn't notice in the dark of the garage the gouges on the planer bed. I used it for the first time the other day and in order to avoid scratches in my wood, I used MixWax finishing paste wax and my files to get rid of the high spots of the gouges. It seemed to work. I applied multiple layers of the wax but still feel the cuts in the metal. It seems to have done the trick. Is there another method that might work better?

@davidstanek7604 5 лет назад

Great tip on the index pins! Always wondered why there was wiggle room for the blade to sit on the housing unit

@gregmislick1117 5 лет назад

You left out step one - get a planer if you dont have one! Other than that great set of tips, thanks. Someday I will apply them.

@JohnMcGrathManInShed 5 лет назад

The woodworking Mechanic!

@harrypowers9412 2 года назад

Love your channel, your tools and your videos. Is the intermittent music really necessary?

@jonwooddell3966 2 года назад

I realize this video was made a couple of years ago, but I recently was given a DW733 when my father-in-law passed away. He left it in an outside shed (for about 8 years is the family estimate) and there is rust in many places. I'm going to buy some replacement blades and try to clean the rust off the roller they mount to, but I was wondering if you have any other suggestions/warnings to help me try to get this planer back on line. Thanks for everything you have shared and taught me.

@snyderhaus 3 года назад

Is it worth upgrading to the helical on the lunchbox planer? Or is it better taking the money and getting a larger planer that has more hp etc to it?

@bijan4727 Месяц назад

Hi very nice presentation. I have a 13 inch dewalt thickness planer. Let’s say I have three pieces of 2X4 and each one them is 2-7/16 , 2-3/8, and 2-5/16 how do I make all three of them being 2-5/16 without manually measuring them. I appreciate your input. Thanks

@MPDesign 5 лет назад

Do a jointer next!!

@txbob 3 года назад

I wish you would have shown the cleaning of rollers. Do you simple green them? Other than that, thanks for a great video and I subscribed.

@zavoina 5 лет назад

I see the digital planer readout for your thickness. Do you prefer that, recommend it, or it was on it when you acquired it? Loving the videos, and be ready to celebrate in a couple weeks - Father's Day!

@katzmosestools 5 лет назад

I love that thing!

@roni3425 2 года назад

Hi Jonathan, Is the bees wax/mineral oil paste you use for cuttingboards usable to lubricate the planer tables ? Thanks in advance Ronald

@maxwang2537 3 года назад

Thanks for sharing. This can be a silly question. I assume there is only one motor in a thicknesser which dives both the cutting block and the feeding rollers. Obviously they rotate at significantly different speeds so there should be a high ratio reduction gear somewhere. How is it maintained, periodic engine oil change? Correct me if this is wrong. Thanks.

@Vman7757 5 лет назад

Some day I have this tool on my list to buy. I hope to have it in November. Can you do a video on how to use it? Or do you have one? I have seen lots of people use one. But they don't go over how too.

@katzmosestools 5 лет назад

You'll see it's pretty self explanatory . Great tool

@TomsPropertyCare Месяц назад

What about deep grooves in the bed? I do my wood working outdoors and didn't notice little rocks stuck to the boards and it gouged the bed.

@nonexman 6 месяцев назад

Since you are already using Glidecoat, why do you use a pastewax on the bottom surface? I've been using Glidecoat on the bottom for years with great success. Other than that mystery (to me), great video.

@mikhailarey1196 Год назад

When opened the top to change the blades it was packed with sawdust. I can’t seem to stop it from filling up. Constantly vacuuming it out.

@lithgowlights859 2 года назад

Started sharpening the blades on my 735 as I am using it to take about 1mm off 25 year old Merbau decking surrounding a pool. After about 100 linear feet the blades are dull and coated with a horrid sap an need cleaning and sharpening. 2 minutes on some 800 grit paper will clean and sharpen the blades enough to get another 100 feet of boards through it. Only sharpened once, but many people say they get 2-3 sharpens before they have to toss the blades Blades here are US$70+ a set, but I have some non genuine blades arriving to test their longevity and hopefully save me some $

@BarrySumpter Год назад

How'd you go?

@lithgowlights859 Год назад

@@BarrySumpter the knockoff blades work well and along with sharpening the blades I can use the plainer for hours with no issue, swapping blades every hour or two.

@MrThedocholiday 2 года назад

Thanks for not beating a dead horse about safety. The idiots who need nagged about safety are tone deaf in the first place & the rest of us can only tolerate one or two warnings before we get annoyed… because we came here looking for good info rather than a nagging woman. Good & thorough vid… Thanks a mint!

@bmbell1919 3 года назад

The Wen manual says the infeed and outboard sides should be about 1mm higher than the cutting table...why would that be? It looks like you are making them perfectly flat across which seems to make more sense. Thank you!

@WiLL02724 28 дней назад

2024 comment/question. Paste Wax is definitely old school, is ceramic coating a better option now ?

@christofix 5 лет назад

Great review / tip video. I'm planning to buy a thickness planer but i don't know which brand to buy. I doubt between the Makita and the dewalt. Are you happy with this dewalt and do you recommend him?

@katzmosestools 5 лет назад

Very happy with the dewalt l. I've had both sizes and they were great. Click one of my Amazon links (any of them) when you're ready to buy. It helps the channel a lot

@christofix 5 лет назад

@@katzmosestools Thank you for that anwser my friend. If they ship it to belgium i will order it that way. That will help you and your channel

@StarscreamGamingYT 5 лет назад

I’ve had my Dewalt for years and it’s fantastic. Never snipe. Don’t even think about the Makita.

@christofix 5 лет назад

@@StarscreamGamingYT Thank you so much Joe. It is great to have some feedback! I realy appreciate your anwser.Thanks

@tomblount5635 3 года назад

I have the Dewalt it's a great planer and comes with a extra set of knives. Don't mess with trying to "level it" n you will be fine. It comes set up from the factory. All you need to do is wax or seal the bed and begin planing. That simple

@paulcuster9578 5 лет назад

Thanks for the tips. I have one of these and was just getting ready to do a tune up for the summer. With this planner, do you have some slop in the hand crank wheel? Mine has a little although it generally holds it's height just fine. Just looking to compare it to another to see if I am imagining something or if it is within tolerance.

@katzmosestools 5 лет назад

Get the wixey digital height gauge. It'll give you piece of mind

@ryanglick3894 2 года назад

I know this is an old post but I was wondering if its possible when you replace the rollers in a 735 dewalt to reverse them. Front in rear and rear in front and if they can what would it do? Thanks in advance for the answer.

@xyshomavazax 3 года назад

I made a long bed for my Dewalt planer, using 3/4” plywood, and I air-spray my planer out after every use. My problem is that I’m getting an uneven cut from one side to another. I can’t tell if the rollers are parallel with the bed, but something is messed up in there. Any ideas?

@acanadianwoodworker 5 лет назад

I have this planer and it generates an enormous amount of static which I assume is from the wood chips bouncing around the attached vacuum hose. When I open the cyclone bucket afterwards the chips are bouncing around like popcorn! I tried grounding the hose wire to a machine screw in the back of the unit, but it doesn't seem to do much. Any tips you can think of, let me know!

@woodsilobuilds7245 5 лет назад

I have the same issue...get a static shock each time I disconnect the hose.

@guitarman_3693 3 года назад

i ran a bare copper 14ga. wire from a piece of romex THRU the middle of the flex tube & ground it to the catch can, if metal.. if plastic ? im not sure... i hope it helps you..

@Henry.Bendik 3 года назад

Love your vids Jonathan, keep up the good work. I just tuned up my old DW733 in the hopes to eliminate the snipe I'm getting. I also added an MDF sled and still getting snipe on both ends of a board. Any idea with might be causing this?

@tomblount5635 3 года назад

Yes. Leveling the in feed and out feed as he suggested definitely increases the snipe. Go back to the original position of the tables. They need to be slightly elevated from the bed. Adjust until most of the snipe is gone. If you still have a slight bit then simply lift up slightly on the out feed board as it passes the front roller and you will have minimal snipe which can be eliminated by sanding. Listen to the this other suggestion and yur doomed to snipe hell!!

@Henry.Bendik 3 года назад

@@tomblount5635 Thanks very much! Can't understand why Jonathan never responded ?!

@rosswines Год назад

Time to upgrade to 735 model perhaps

@richardspencer742 5 лет назад

Commenting just to help you out ;-)

@katzmosestools 5 лет назад

Thanks Rich

@guitarman_3693 3 года назад

ok. right away 6ou cowered away from what im looking for... and yes , im gonna time the threaded post and bring the planer back to level.... bye. good luck with your elementry vid.

@indieOttawa Месяц назад

It won't be long before you are giving us how to Tuneup your baby :)

@JoshHarrisPhotography Год назад

Just to be clear, are you using Simple Green on the rollers as well?

@williamsimpson2083 5 лет назад

Are you going to do videos on bandsaws and pillar drills?

@katzmosestools 5 лет назад

Yep

@aarondrossart6026 3 года назад

I have the ridgid lunchbox planer and the infeed/outfeed design is pretty dumb. Wishing I would have spent the extra couple hundred bucks and and gotten the 735...

@garriv777 Год назад

When is DeWalt going to come out with this model that has a helical head already installed? Come on DeWalt, get with the times!

@pacoclbhs 4 года назад

Hey mr jonathan! I recently tune up my planer dw733 but the right side is thigher than the left side and I don’t know how to adjust it 😬

@tomblount5635 3 года назад

Your first mistake was adjusting it. It comes set up from the factory. A lot of these so called experts don't know anything about the planer and they think they need to have the infeed and out feed shelves level with the bed? That is totally bogus. You greatly enhance the snipe by doing that. Leave it alone. If you have leveled it then go back and slightly elevate each side until the snipe is minimal. Listen to this guy and yur guaranteed snipe

@rosswines Год назад

Time to trade up to 735 maybe perhaps

@tomasmendoza866 2 года назад

First off Jonathan, thank you for all your content! I’m just getting started on my woodworking journey so I’m soaking it all up! Question I have is what planer model is that and would you recommend it? I have someone I meet who is selling a dewalt 734 and am curious if that’s what you have there. Thx!

@AxGryndr 2 года назад

This is the DW735, the 734 is the more traditional lunchbox style planner with 2 posts while the 735 is a four post.

@BarrySumpter Год назад

Anyone reading this late after the fact. 735 hands down.

@foxtrotdeltausn4757 5 месяцев назад

So.... what if you just got this exact one used and one of the screw legs has loosened and now it is bound up?

@MattyE316 Год назад

Hi, I recently bought a used DeWalt planer and went to change the blade and the screw on the top is just spinning. I got the other 3 out. I can't pry up because it's recessed. Any thoughts?

@jguild45 Год назад

Where is the link to the Jay Bates snipe video?

@joser1219 5 лет назад

My planer is a Ridgid and I'd like to know if the rollers can be tightened or adjusted. I thought I noticed, when passing a board, the rollers move up in a spring like motion and leave a 4 inch long snipe.

@katzmosestools 5 лет назад

I'm not familiar with that one. I would look up the instruction manual

@Romski1978 3 года назад

Hi what blade r u I using in your planer

@SkyBoss52 4 месяца назад

HELP! My brand new DW 735 does not plane evenly across the width of a 12 1/2” cutting board glue up. If I reverse, as you mention in the beginning of this video, my board is left thicker in the center than the edges. This is a big problem when cutting into 1 1/4” thick pieces for end grain cutting boards. I’ve taken close measurements and the cutting head is not parrell to the bed. Can you point me in the right direction for adjusting? Thanks

@coloradomountainman8659 Год назад

I had my 735 for 3 days. Took it back. Worst snipe I've ever had on a planer, and I've been using shop planers since my first one (Makita 10" ) back in 1980, regardless how I fed the material. This machine also ate blades. Less than 10 minutes planing clean pine 2x8's and the blades were rendered unusable and that was while taking less than 1/16" on a pass, about 1/2 turn on the handle. Switch is in a terrible location, nothing to keep a board from hitting it and turning the machine off when sliding a board across the top and positioning it to refeed it. Then there is the chip exiting the machine at 200+ mph. There needs to be a way to disconnect the blower to be able to just have the chips drop into a receptacle. And lastly, as if this wasn't enough, the power cord is on the wrong side of the machine, creating a tripping hazard unless you do some magical rerouting. Back to using my 25 year old Ryobi AP13 which still performs remarkedly well after a million miles of use.

@chopwoodcharlie 4 года назад

My planer is displaying the problem you addressed initially, planning out of square. You mentioned that there is no simple fix for this. However, I deal with very close clearances in my work and passing it through again is not really a good option, I am determined to fix it. Have you ever attempted fixing this? Any advice would help. Thank you.

@danielpittman889 3 года назад

You'll need to rotate the screws at one end of the machine. On the DeWalt 735 there are two screws on each end - most lunchbox planers have one screw per side. Anyway, give the screw or screws on one side a quarter turn and see if the problem gets better or worse. It's a fiddly process of trial and error and some tools are easier to adjust than others. See if your manual has detailed instructions.

@thomasdavisiii1 5 лет назад

Sealed bearings

@godsmwc65 5 лет назад

Where is the link on Jay bates planer table ? Moses ?

@katzmosestools 5 лет назад

In the cards on the upper right hand corner of the video

@tomw4231 5 лет назад

You mentioned a link to a Jay Bates video for a planer bed. I cannot seem to locate it. Thanks.

@katzmosestools 5 лет назад

It's in the cards. The little "i" in the top right corner of the video

@tomw4231 5 лет назад

@@katzmosestools Ah, there it is. Thanks.

@marshallmurrell4583 4 года назад

I disagree with your advice on adjusting the cutterhead to be parallel. That said, my planer is not a DeWalt 735, and it may be different for that planer. Mine is a Delta 22-555. It was fairly significantly out of parallel with the table. If one follows your recommendation to simply turn the board around, won't you wind up with a crown in the middle of the board? At any rate, I disassembled my planer and got the cutterhead to within .003 " over the 13" length of the cutterhead of being parallel. I used 1-2-3 blocks and feeler gauges. It took me about an hour and a half to do that, which was significantly less time than correcting the thickness difference in six pieces of walnut that I had cut for use in two bedside tables. I also took the opportunity to give it a good cleaning and lubricated screws and guide rods. Vertical adjustment is now much smoother and noise free.

@-11BRAVO- Год назад

Pro tip: last time I was cleaning under my blades on the cutter head my intelligent self ran my finger down the blade and it’s so sharp I cut myself down the whole 12.5 inches and was bleeding before I realized what was happening

@roywescott 3 года назад

I HAVE A QUESTION. THERE IS A PART, THE CUTTER HEAD LOCK LEVER. IT HAS A SPRING AND IS ADJUSTABLE UP AND DOWN. IF YOU TIGHTEN IT, IT DOESNT’ MOVE, LOOSEN IT AND IT WORKS UP AND DOWN WITH THE SPRING. AT WHAT POSITION ARE YOU TO TIGHTEN THE SCREWS. DOES THE BRACKET NEED TO BE UP OR DOWN. DESPERATELY LOOKING FOR ANSWER.

@rosswines Год назад

Lock lever goes back into normal open position when the dust collector is bolted back on It's basically a safety lock out item. With cover off you need to press down to rotate the 3 straight blades when servicing them. Simples

@michaelbennett5386 3 года назад

my dealt planer has fins on the inside of the vacuum out port , I can't get 2'' hose inside.I tape on and it blows off, any suggestions.

@brentriddersen9882 3 года назад

Its meant to have a 4" hose around the dust port. Then you can use a clamp on the hose to keep it in place. You need a 4x2 reducer and 4" hose and a couple clamps

@tomblount5635 3 года назад

@@brentriddersen9882 it's very simple to get a metal dryer hose 4 a screw clamp and attach to the 4" exhaust. Run the hose to a 30 gallon trash can. Problem solved no expense hookup or attachments or duct tape!!?