This handmade tool will remove hardest type of Bearings || Blind hole bearing puller 

Dear Boris Bearing have a cage for balls I remove it because it was damaged and the ball was not missing. But the cage is not problem for use this way. And other size of bearing need other size three shafts. I want to show a way for pulling bearings 😉 I think it's one of the best

@@innovationtime20 you are right , is better than cutting it. Who's Boris ?😂

👍👍😂😂 my dictionary Chang Horia into Boris Dear Horia

No, the bearing cage has failed, only about 7 percent of bearing failure is caused by the result of this problem, most bearings are making so much noise (saying rI need to be replaced) by this point you replace them.

Yep. Utterly useless for any kind of sealed bearing!

👌👌👏👏💐💐

🙏🙏🌹🌹

Very good and innovative.

❤️❤️

🌹🌹🌹

❤️❤️

Thank you dear RICKY 🌹🙏

Thank you dear John 🌹

👍👍

@ Ron Bianca, How did the suggested method help to pull out the bearing!

@@madhusudangupta3661 After putting the bolt in the hole,adding molten lead and letting it cool down it provided me with a handle to pull the bearing out.

@Jambo They were not loose. It was the only thing I could think of at the time and it worked!

Thank you dear faramarz 🌹

🙏

Thanks dear Angie 🌹

Exactly bro Different size of bearing need different size of studs 👍

Thanks bro 🙏🌹

🙏❤️❤️

Thank you dear Frank 🙏🌹

Thanks bro but no ball was missed but the cage of balls was removed

sealed bearings are not sealed. the seal can be popped out easy with a small screwdriver or pick.

Wouldn't work very well? It wouldn't work at all on anything but open bearings without all of its, ahem, balls? Basically for scrapyard finds where you're getting rid of the bearing to salvage the part for something else. In most cases though, a regular bearing puller works just fine 🤣🤦‍♂️

Thank you dear Duke 🙏🌹

🙏🌹

Thank you dear Juan 🙏🌹

🙏🙏🌹🌹

❤️

That’s what I was thinking. Cool idea and all but pretty limited. The time it would take to make this tool would be better suited practicing with a torch or welder.

🙏❤️🙏

🌹🌹

🙏🙏🌹🌹

@@innovationtime20 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

Thanks bro 🙏

Thank you for your comment dear Colin 🙏🙏🌹🌹

Thank you so much dear Gilbert 🙏🙏🌹🌹

There is people like you and me and others that have to go through the system to get a piece of paper to show how good we are so we're allowed to practice engineering that is wrong

❤️❤️

❤️

Bravo 👏👏

@@innovationtime20 This proves your trick is not worth the time of the viewer.

@@madhusudangupta3661 Two totally different applications. One has nothing to do with the other.

Thanks bro 🙏🌹

Thank you so much ❤️❤️

Thank you dear Imma for your comment 🌹🌹🙏🙏

This was exactly my thought- why not just use off-the-shelf bearing separator with T-bar and forcing screw. I think a Harbor Freight kit is about 75-100 bucks or rent one from your local parts store. Very good idea though, A+ for quality work & ingenuity!

if you cant get anything to grab the back side those pullers are useless. the ones that expand break easily they arent a few bucks you end up throwing $40-50 in the trash when they do break. also if you have all the tools and materials on hand you only need the time to make this tool.

@@darkshadowsx5949 ...completely agree.

No dear Shane

@@innovationtime20 you should, we use pullers and that idea is one of the best I have seen.

Thanks bro 👍 It depends on the size of bearing bro

❤️❤️

I think most tool store have this I bought it from one of them bro 😉

@@innovationtime20 I never see that size

😕

@@brucebonkowski7253 Try Starrett

👍

No bro

🙏🙏🙏🌹🌹🌹🌹

You can remove it with welding When it welded and deformed easily pulled out 😉

❤️

Just the cage of balls was removed

Удалено для лучшего отображения Но он также работает с разделителем

Hi dear Michel I want to use this bolt to prevent spinning the front pice, it has to take by a wrench

@@innovationtime20 Hi I,m a mechanic , and you are absolutely right , application pending , Thanks for youre reply Michel

🙏🙏🌹🌹

Hi bro Metal sealed or plastic sealed can easily remove with a sharp object 😉

👍

Just three rods for each size that is one way, another way is another bearing puller that I have made it before, I have a play list for bearing puller If you like you can watch this bro 😉

Just missing the cage bro👍

🙏🙏❤️❤️

Hi dear Joey The cage of balls just removed to better show how the studs work, when the cage removed it seems some balls missing, you can try it bro 💐