This is how you repair a laptop by not jumping a mosfet 

I don't care what anybody say, this is a flawless victory, the irrelevant parts of the video is what made this one suspense filled, AWESOME ONE mr Bongi.

Hello, I just wanna say Thank you for giving the links for schematics. Now I can learn on how to repair motherboards with your videos. Please upload more and more videos. More power to your channel 👌🏼💪🏼

Great video. Very nice way you make it, showin schematics, graphics and good board view. Explanation is good, informative and a relaxing.

This is OK: a shorted mosfet. The problem is when the 2 mosfets are fine. You must suspect about the IC charging pump, which manages the mosfets' gate.

Keep up the good work bro, I'm your new subscriber.

This is a very good job. Thanks for sharing with us.

IF you did not have a donor mosfet, in this case since they are the same and only the 1st mosfet is broken, you could have switched the 1st MOSFET with the 2nd MOSFET and THEN jumped the 2nd mosfet with a wire. Then the charging chip should be safe. Of course, replacing the mosfet with a new one is always better but if you are in an emergency, this could have worked too.

your presentation is very good and clear for me

Thanks. Great video & super clear instructions. What flux are you using please?

Thanks to your video this helps me a lot😊

Great job! Your knowledge is excellent. What microscope your using here?

I've been working on Toshiba l850 boards recently. One I jumped eventually failed. There was hole in charge ic. I think you are right. Best not jump. Another can't get powering. Seems like signalling from EC to charge ic bad. Anyway I'll play until it's fixed or I die.

I just tested some power banks, how to make them stronger, and what to do to reach their max output power. The solution is simple, connecting a 4.5V soldering iron to the USB port and use it for testing bad boards. Some get stronger in 2 minutes, some need 10 minutes to reach max power (older devices).

Watching the way you repair and technique good day

I'm new to this board repair thingy. I've watch your videos numerous time. Its very helpful. It hard to repair thing you don't have schematic for it. Is there schematics files you can share with us here?

what about that knocked capacitor?

Useful video, thanks. I assume it needed a new screen after you'd dragged the motherboard over it a few times? Surprised you didn't protect it...

Excellent video

Hi great video, can you do a video on how to replace a mosfet by reading the lettering on the mosfet, as I agree with replacing it but how you read the letters on the mosfet and if you can't get how too find the one you can use, your very good at what you do👍😁

Is it a special gel type flux you are using ? I have only a liquid flux pen.

Nice work bro 💪

Please help with lenovo g50 A-362 REV 1 that you used to repair 🙏🙏

Thank you sir..very helpful video..

Hi have you schematics for samsung np270e5e-x06fr please??? Thankyou

Pls sir… what are criterias for changing the first mosfet? Must it be from the same type of laptop/motherboard? Or any mosfet with same number? Or just change from anywhere? Or can u replace N channel with any N channel and P channel mosfet with any P channel mosfet even if is not the same number? 🙏 pls help me

I want dell all in one schematic model 20- 3048 do u have

how many degrees of heat to remove the mosfet IC? thanks sir

Hi bro i have a lenovo G580 The problem is restart no display when I remove the ram it's stable start and hold on but if put ram it's again restart is there any help and suggestion

Brother what course would you recommend for me to take to learn more ngama electronics.

Sir in a situation where you bridge the first mosfet and the charging ic got damage. What will i do? I bridged my first mosfet and now the charging ic gets hot each time I plug in my adapter. What’s the solution

nice job

Nice job bro. Please let me know which microscope you are using??

Very nice

Please upload Part 2 book for advanced users thank you 😇😇😇

Thank you for this. What if laptop starts normally, loads windows ok, progs run ok, but then fans go max and then it all shuts down? Any idea what to check. Also doesnt see nvidia gpu anymore. Hasee n95. Thx

I understand but I used to bypass two mosfets and it charges , can you explain please ? I know in newer laptop the BQ chip won't allow that but how about older laptops ? I tried it myself in hp pro book board which first two mosfets was burned and welded to the board and I bypassed them with jumber wire and laptop was working and charging

what's that paste (liquid ) called 11:54 ???

If a mosfets number ends in an even number its an n channel and if it ends with an odd number its a p channel mosfet thats what i learned to do

Hi there , it was very useful and informative tutorial video . your explanation is very simple and perfect . keep it up . thnx

Thank for your amazing video, Please advise where I can get free Schematics ! Thanks

Brilliant as usual however a bit more analysis possibly next time please ?

what flux exactly do you use please? it looks good

Hi do u sell second hand laptops?

Im located in gauteng and I have a same lenovo laptop that doesnt power on. Is there any possibility that we can make a way for my laptop to reach you for reparations?

❤

Its very strange, he is holdin MM at buzzer mode and he is checking 3v and 5v 🤦‍.

Bro just hot glue it together, its simple

it does not work spacks you know

First

I often wonder how a screen gets scratched when repairing the circuit board and now I know, people like you sliding the board on it like it's a work bench and when they ask you how come it's scratched you tell them it wasn't you you were working on the circuit board, really bad abuse of a customers property, very very unprofessional.

Can you tell me where to get Asus schematics from?