Тёмный
No video :(

Throat Plates for the Ridgid R4514 Table Saw 

Diamond Woodworks
Подписаться 367
Просмотров 7 тыс.
50% 1

Instead of buying a dado throat plate for your ridgid table saw, DIY! All you need is 1/2” MDF, your saw, a jig saw, sander and a chisel! The first one takes a bit of time, but after that you can’t batch these things out!
Crosscut asked Build:
• Reversible Crosscut Sled

Опубликовано:

 

18 мар 2022

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 24   
@stevesfascinations1516
@stevesfascinations1516 Год назад
Good Job! I am going out to make one for my saw. Thanks for doing all the legwork on this, I was about to re-invent the wheel (again). Thumbs up and subscribed.
@diamondwoodworks6373
@diamondwoodworks6373 Год назад
Thanks! Hoping to start making videos again soon.
@marcuspullan1142
@marcuspullan1142 2 года назад
Jeff, thanks! I’ve seen a few videos but nothing a quick and easy as yours. Well explained. If I have some 1/2” down in basement, I’m making both the zero and dado stack face plate
@diamondwoodworks6373
@diamondwoodworks6373 2 года назад
Thanks and good luck!
@SongThatWomanOverThere
@SongThatWomanOverThere 5 месяцев назад
I really appreciate you for creating this video. The R4514 has been discontinued!!! I cannot find the table saw at all on the Ridgid site. I was searching for parts on 9Mar2024 in Alberta, Canada. There is no lifetime warranty when they stop making the product. Very disappointed about not being able to get parts. Again, thank you so much.
@jefffleming8103
@jefffleming8103 2 года назад
I just got a r4514 and was wondering if I could make a throat plate ..And after watching 👀 you I will have no problem thank you so much jeff
@diamondwoodworks6373
@diamondwoodworks6373 2 года назад
It was really straight forward. The first one will give ya a little trouble, but after that it’s super fast/easy.
@sgtstop
@sgtstop 7 месяцев назад
Thanks, Airborne! AATW! Great video. I know what Im doing next with mine!
@johnpetrea
@johnpetrea 6 месяцев назад
Thank You for sharing this information
@stevedarnell8444
@stevedarnell8444 2 года назад
If you take your wife’s lipstick you can put it on the mounting pads. Then when you put your new insert down it will mark where you need to knotch out your insert.
@diamondwoodworks6373
@diamondwoodworks6373 2 года назад
Good idea!
@terryray4646
@terryray4646 7 месяцев назад
Is there a throat plate for dado cuts with this saw?
@danielvaldez3778
@danielvaldez3778 9 месяцев назад
Can this table saw use dado blade?
@masterlordking
@masterlordking Год назад
just picked up the R4514, and need a dado plate $40 (I dont thank so) thanks for the video ,
@diamondwoodworks6373
@diamondwoodworks6373 Год назад
Exactly! Especially since this throat plate is pretty straight forward.
@ahomesjourney3225
@ahomesjourney3225 2 года назад
To make the dado plate, did you notch out with a jigsaw or keep running it through the table saw?
@diamondwoodworks6373
@diamondwoodworks6373 2 года назад
The dado plate was actually way easier to make. After making the zero clearance I knew where to remove material from underneath, and took care of that with a chisel. Once it was laying flat on the saw just slapped my dado on it and slowly raised the blade. No need to notch anything as the riving knife is removed when using the dado stack.
@egray8449
@egray8449 Год назад
How is the plate held in on the opposite side of your screw/washer solution?
@diamondwoodworks6373
@diamondwoodworks6373 Год назад
Just with a friction fit. Got rid of that particular saw but never had an issue. Most zero clearance inserts I’ve seen/used rely on friction (like my current saw/throat plate).
@dashermike3207
@dashermike3207 2 года назад
wosh you had a video on this for the R4513. My factory throat plate is terrible....not even flush with the table surface.
@diamondwoodworks6373
@diamondwoodworks6373 2 года назад
I believe that one has a rounded throat plate. Should be the same idea… with a little jig/band saw work!
@dashermike3207
@dashermike3207 2 года назад
@@diamondwoodworks6373 its a rectangular shaped one
Далее
Zero Clearance Throat Plate for Ridgid Table Saws
7:48
Ridgid R4514 Impressions
14:31
Просмотров 12 тыс.
Mastering the Dado Stack: No BS Advice for Woodworkers
14:45
Zero Clearance Inserts for Saws.  You Need One!
7:09
Просмотров 37 тыс.
zero clearance insert plate - Ridgid table saw
5:51
Просмотров 135 тыс.
How To Align Your RIDGID Portable Table Saw
11:28
Просмотров 148 тыс.