Tinyhawk II AIO Motherboard REPAIR 

I've gone through lots of these boards, please do more TinyHawk 2 repairs!!

you should start an fpv repair group. we could all share idea. would be a great idea for common repairs !

I love this content man, I wish more people were into the electronics repair. Everyone thinks it's super difficult but, it's actually pretty easy with just a little bit of knowledge and a hot air gun. 9 times out of 10 the problem is an ldo that costs a few cents to repair I hate thinking how many boards get thrown away that could have been fixed.

You can't imagine the time i spent serching where was the issue... You're right, the blue led is the Frsky D8 receiver and i think it burnt when the transistor did... And i think it burned because i shorted the 3 sbus pin. Great work!

This is pretty cool, my Gyro seemed to fail and I only had to reflow the solder joints lol.

The level of skill and knowledge showed in this video is just amazing. Thank you very much for share it.

Best repair videos! Keep the good work Livyu!

Always love to see the repairs Thanks for the video

Wow this is really impressive. I have a strange issue on an almost new TinyHawk III right now. When plugging in the battery, there is no beep, and the AIO board's red LED flashes a few times fast - then nothing works (the separate VTX board works, but not the FC/ESC AIO). No arming, no motors spinning, no usual betaflight welcome beeping - just silence from the board. The red and blue LED should blink, but the blue led stays dark and the red LED, as said above, only flashes around 4 times, then remains dark. Instead, however, the motors are ticking around 2x/second, which I have never heard before. Now I tried plugging out the motors, and I found out that when no motor is plugged into the front right motor plug, then I get the right beep, the right blue and red LED blinking and I get USB and I can spin the remaining 3 motors in betaflight. I also switched motors to check them, and all 4 motors appear to be okay. However it does not matter which motor I plug in to the front right motor plug - always when the front right motor plug has a motor plugged in, the symptoms (no usb, no beep, only red led flashing, motors ticking) appear again. I checked the top and bottom sides of the AIO board and I cannot visually identify any discolored electronic components. The motor plug socket appears to be normal and undamaged. (The symptoms did not occur after a crash, but started between two flight sessions. The last good flight session was without any signs of something being wrong. I did pick some hair and dust out of the motors after flying, but everything seemed okay. The motors are definitely clean and running - only the top right motor socket creates a problem for the entire board.) Any clue what I can do to figure this out? I'd love to be able to repair this board. I have some basic knowledge of electronic components, I can do some soldering (however, the parts on the board are so tiny, I doubt I could safely solder resistors on there), I am willing to learn. I just see no trace of heat damage or other fishy symptoms except for the described faulty behavior.

thanks for making this video , this is great , id like to see how to repair mosfets on aio boards also

Great video as usual!

So satisfying to see the board get cleaned lol

Excellent! this is along something I have done many times with my own stuff. People need to learn things that are useful! Electronics is one of those things, as pretty much everything around us is of an electronic nature. We have to learn how things work, so we can fix things ourselves and save $ in the process, knowing how to repair thing is very powerful. While this is aimed at an item that we use for our hobby, the approach and technique applies to any type of electronic board repair. Thumbs UP!

Good skill on repair ! Thank for this

thx for sharing. aways nice to watch

You have a great skill~!👍👍👍 Awesome~👍

Love it dude

Great Skill 👍

I have three of those boards that need to be repaired this is a start thank you

Can u do more videos on fixing micro whoop boards like the most common issues ur a genius thank you for your time and hard work

Bravo !!!!!

good job

Nice !! I like repairs vidéos :)

I just fried this AiO yesterday. I needed to replace the power wire, because my XT30 connector broke (soldering on the Plug came off on one cable) and I failed to resolder it to the small XT30 and it melted lol. I ordered some pre-soldered XT30 cables, but didn't realise I ordered 16AWG wire sizes and I still tried to solder that onto the tiiiiiny pads on the AiO. I failed. Hard. Didn't dissasamble everything fully, just enough to get to the pads underneath on the side. Bad decision. I became frustrated and careless. I didn't care about annything anymore and overheated everything waaaaay to much and to long. Cooked out Flux sooo much, had to add so much with my Pen lol. Couldn't get solder onto the pads, then it 'spilled' over the pad onto everything arounnd it and I had to clean it up. I seriously fucked it up majorly. After 1 Hour of getting mad I had both wires soldered with the worst jointns possible and tried plugging in a 2S LiPo without a smokestop. Some LEDs flashed up shortly, but not for long. Wiggling it a bit at one point it stayed on for long enough to almost boot up once before flickering again and then nothing, quickly unplugging again. Simply pulling the Battery out of the XT30 I pulled of one wire from the solder pad as well lol. I don"t know if it is fixable or what to do about it. Plugging in via USB it still connects to BetaFlight so I guess just the Power Distribution is fucked up royally and I neither have the tools nor the skill to fix it. Don't want to buy yet another AiO for 90 bucks. This was my second board since I crashed in a Puddle once and some Chips on the ESC area burned up and I replaced it. Thinking of getting a custom Frame from Microheli that fits the TH1103 Motors with the awkward mounting patterns and rebuilding it with another AiO completly or even small stack with seperate F4/F7 FC + ESC because why not and because I already have so many spare Parts and replacement TH1103 Motors.

Really looking forward to your DJIFPV Air unit teardown. 👍

When I have such a hole in the element, I am looking for a tile on google in the photos. easier and faster than finding the paths where it goes. I recommend checking this way.

Video begins Livyu : hi, I am leave you. Bruh, the video just began. Jk mate, thanks for all the wonderful videos.

very nice video man! how do you know what component to use when you find the broken one? for example how do you know it taht was a double diode or a transistor, and in case which transistor to use? keep it up mate!

Super content! Thank you! But how do you know the part was a transistor and not a voltage regulator or diode ??

youre real man

Very well, you are a genius to me. I have followed all your videos, in order to repair a Tinyhawk, but have not yet succeeded. I would like you to tell me which component is the one I marked in red in the photo attached to the email I sent you. It's a kind of reel, with an underlined K on it. There is also another one under the small PCB of the video transmitter. Thanks for your help. Bruno.

Excellent video, congratulations, I have the same FC but damage in 2 mofset to ESC, as I find them on the web, what reference are they? thank you very much for your help

I wish I had your skills I really like fixing electronics only if I knew where to start.

what is the transistor you use'd?

Hello there! Thank you very much for the repair videos. I have an Aikon ak32 35A 4in1 esc that doesn't ppwer up. I was trying to spot the issue and i think it the the voltage regulator that is right after the power lead. I found a picture that says E39 on it but i cant find any info about it. I would appreciate any help!!! ❤️

Thanks bro, I got a Jhemcu that is screwed up somehow, and maybe some more stuff. Where do I send it?

I solders a new pigtail on mine and now it doesn't work. Done it before several times with success. Any idea

🔥👍

damn! i wish i could do this!

Excellent job... and the alcohol trick was new to me, but i guess you wouldn't do this on higher voltage boards ?

Hi, had a bad day with my Tinyhawk 2 Freestyle, tried to upgrade the VTX an it shorted out the FC with a little smoke an then stoped working! Can you tell me where on that FC board would be the problem that shorted Out an what is probably burned out from the VTX shorting out the FC? thank you!

I would like to make a upgrade with eachine tx805 and GPS beitian nn 220 t . With 2 s batteries schould do his work!

How much temperature you apply by heat gun?

I got one where the 3th and 4th esc don’t work…where to I check and how? 🙏🙏🙏🙏🙏😃😃😃

When I plug in a battery. The lights come on but the motors don’t beep or anything . Dosnt output video to the goggles either . Could that be the cause ??

USB is not recognized, is there a way to connect?

Nice! Love things like this. What kind of hot air device is it you use for these repairs? Or something similar to it.👍

Hi Livyu, forgive my english with google translate! I ask you for a lot of help, after weeks of research I cannot find a solution to my problem: at minute 0:26 the inductor that you have replaced is framed in the lower right corner and which is indicated by the factory with a K underlined. Could you tell me where I can buy it? I can't find his values anywhere on the net and my thinyhawk is without video signal for that reason. I sincerely hope you can help me! Thank you!

thank you! the inductor looks bit banged, too. i have two boards which are failing due to similar damage. one gets "rxloss" plenty and the other has the jitters in flight. can you probably show how to replace these tiny inductors? they seem to be hard to get off the pcb.

Anyone got a source for the FETs (SM2221CSQG)that are used on these emax aio boards? The FC costs nowadays more than I paid for my tinyhawk back then 0o

Hey can you please do a video on diagnosing and repairing the tinyhawk freestyle 2 AIO board? I just got one that lights up with battery power but nothing when usb is connected and can’t connect to the computer.

hi, how can i solder the cam on the FC? the pin is broken

NIce video! do you recommend any flux from aliexpress or similar? regards

A question: all those TH2 boards, including the one in your video have an inductor with a chipped off corner. Do you know what it is and how came that every board has a broken (?) inductor case? Is it on purpose for some technical reason?

Great repair, i got the same board and it is not connecting to the PC anymore. LEDs are lighting up and i have 5V from ESC is in place. Would could the issue be when there is no connection to the PC via USB?

I am facing a weird problem. One of my motors stopped spinning today. First my quad was wobbling, but after 5 mins of flught my motor 1 stopped spinning completely. How do I diagnose it and how to repair it. Can I simply replace one motor connectiin with a 6A esc. Please help.

I have some broken stuff where do I donate it to? I have a lot of these tiny hawk boards

Mine caught fire and burnt my house down .I'm looking for the neighbors house now

I'm the First bro

3:00 i use an old toothbrush and isopropyl alcohol to clean glue or residue. It's safer and faster imo.

Butonelu' pt macar 10 deodata Aprecieri unde lái ascuns?.. :)

got exact video.. thanks man now I need to find correct transister , .. other side of board has 1 more transilter at 30 sec (labelled with 662L), that is broken for me. how to identify this transister is NPN or PNP ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-xrjhuOSficg.html