Toyota Corolla Replacing the Control Arm Left Side

Подписаться 29 тыс.

Просмотров 80 тыс.

50% 1

How to fix a clunk when braking, I diagnosed this as needing control arms, this is part 2 of 2 videos. Please use my Amazon Affiliate link and help support my channel:
Lower Control arm kit: amzn.to/3H269Xq
ANPUDS 1/2-Inch Drive Torque Wrench: amzn.to/3THpwfW
ANPUDS 3/8-Inch Drive Click Torque Wrench: amzn.to/3tDkLcI
ANPUDS 1/4 - Inch Drive Click Torque Wrench: amzn.to/41F3mwX
ANPUDS 1" - Inch Drive Click Torque Wrench: amzn.to/3vbJXazTorque:
Torque specs:
Steering knuckle at Shock absorber 113ft
Suspension support at Piston rod 34 ft
Suspension support at 29ft
Suspension cross member at Body Bolt A: 116 ft
Suspension cross member at Body Bolt B: 83ft
Suspension cross member at Transverse engine, engine
mounting insulator 38ft
Steering knuckle at Lower ball joint 76 ft
Lower suspension arm at Lower ball joint 66ft
Lower suspension arm at Suspension cross member 101ft
Wheel lug nut 76ft

Авто/Мото

Опубликовано:

7 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 161

@thewishmastur 2 года назад

God bless you for making these videos to help others. I keep coming back to watch them as this is my first time tackling it. Please do not edit out any parts that you ran into difficulties. We need to learn from them. Thank you.

@dannysdiygarage 2 года назад

You’re welcome, thanks for commenting

@blestplays 5 дней назад

The editing and angles lightning continuity great cinematography

@eraserbuddy213 Месяц назад

Danny i stumbled upon this channel last night and im blown away by the amount of detail and effort you put in. Thank you for sharing your experience and knowledge with us

@dannysdiygarage Месяц назад

Welcome aboard! Appreciate your support

@thewishmastur 2 года назад

The hardest part is lining up the horizontal bolt into the arm.

@burnttoste7581 Год назад

Thanks for the video!! Saved my parents over 500 in labor cost. You really helped me out alot! Thanks again!!

@dannysdiygarage Год назад

Glad I could help! ♥️

@selwyn13 2 года назад

Dude I gotta give u a lot of credit for being able to do all this on the floor w/ a jack. I helped my coworker w/ this at the shop I work at on a Lexus RX300 which had this same exact set up on the lift, and that was already hard enough.

@dannysdiygarage 2 года назад

Yes, it made the job more difficult, but you do what you have to to get it done. Right!

@selwyn13 Год назад

For your Corolla is the camber adjustment that left bolt? I’m assuming it is, right?

@edward1927 9 месяцев назад

it isn't. really is no adjustable camber, you might have a little play where the strut attaches to the knuckle but not many cars have adjustable camber these days.@@selwyn13

@madk5513 2 года назад

Thanks, works on my 2015 corolla, it was a pain adjusting the jack back to original height to match the mount holes for reassembling, lots of prying effort to get control arm in and out but nonetheless i got it

@dannysdiygarage 2 года назад

Thank for commenting on your success

@Ezq95 Год назад

Great video and explanation 👍. My daughters 2012 Corolla S has 106k miles, and it started to sound like it needed struts. I'm going to swap out the front struts and Coils springs,Lower Control arms,Tie Rods,Sway bar bushings,Sway bar Linkages, and 4 brand new Goodyear Tires. I will be starting at 7:30 am tomorrow morning. The tire will be mounted and balanced, then alignment the front suspension by Firestone tire service. MOOG Brand Suspension except The Struts and coil assembly is sold by TRQ. Let's hope I can accomplish 🙏 it. I have never done this before. Thank you for your video. I will video myself trying to execute this change and experience.

@dannysdiygarage Год назад

Please update me when you’re finished, I will love to hear how everything worked our👍🏼

@klausmikaelson7004 2 года назад

You saved me a lot of money. Thank you so much for the video, I wasted 2 hours to figure it out until I found this video. I tried everything to take that bolt out.

@dannysdiygarage 2 года назад

You’re welcome, glad I could make your life a little easier 🍺

@reynaldogonzalez8209 2 года назад

Yeah, me too, jajajajaja

@loptixl Год назад

We ran into the same issue with the bolt and decided to drop the transmission pan instead. Definitely messier but came out like a charm and saved us from having to break a lot of bolts loose to life the transmission. The idea of widening the spaces where the control arm came out are definitely a plus! Thanks.

@callmebackfriday2 Год назад

@@loptixl That is what I was thinking because I have issue remembering all those nuts and bolts need to go back the same way. Can you confirm drop the pan has enough clearance. I may need to change the transmission filter anyway and perform Drain and Fill. Thanks in advance.

@lotwizzard1748 Год назад

@@loptixl i have a standard transmision,i wonder if i might get lucky and have clearance to get that one out

@stoner420b8 Год назад

People like you deserve alot of subscribers , we learning from you , we apreciate your time and effort 🤝

@dannysdiygarage Год назад

I appreciate that, I wish I had a lot more subscribers also, I'll keep trying if you keep watching, thanks

@thegreedybaker3632 25 дней назад

6:21 @@dannysdiygarage

@David-gu8hv 2 года назад

Thanks for the Great Vid! I was a bit surprised this video only has 13 comments since it's the best of about 6 I watched until I realized that probably not too many people are doing their own driver side lower control arm...

@dannysdiygarage 2 года назад

Yes it always surprises me what video’s do well and which don’t, sometimes I’ll spend days and weeks editing and get hardly any bees others a 10 minute edit and it’s a hit, crazy

@renan8486 Год назад

The best technique so far for a Corolla. I think it would work in mine which is a 2010.

@kelving4876 Год назад

I spent a good 2 Hours trying to lift the transmission (I took off the pivot bolt) and once i took off the entire mount the transmission finally gave me space. - 1999 Toyota Corolla

@dannysdiygarage Год назад

Great information, thanks for adding

@tomctutor 10 месяцев назад

Very good video. I done my 2004 Corolla likewise, but got garage to do ball-joints (wasn't sure how easy it was but they didn't charge much for that item, with hindsight could have done that part myself). Just a hint, leave bracket connected to engine block, long bolt, only need to remove top bolts connecting to chassis. 👌🛠

@dannysdiygarage 10 месяцев назад

Thanks for this

@ImAlwaysRightjustaskgoogle 9 месяцев назад

ALSO DONT SPREAD PARTS DESIGN TO HOLD BUSINGS TIGHTLY, AND DO NOT DRILL OUT BALLJOINT BOLT HOLES, SMH

@gavinwinks5953 Месяц назад

Great video. Im going to be changing my control arms and cv axles and this is a great help. My transmission oil pan gasket has a slight leak and I'm going to be changing that as well. If i remove the pan will I have access to removing that horizontal bolt?

@callmebackfriday2 Год назад

OMG, I am so glad you made this second video. I don't know it has to raise the transmission. BTW, how do you know you need to change the control arm vs ball joint. The reason I ask is I have clunking noise from the passenger side and it has noise when I turn, start and stop. It is a 2009 Corolla and it has the original Ball joint for 13 years / 190k miles. I figured out it has to be the ball joint but after watching your video, it "may" be control arm too and the effort is totally different than "simple" ball joint. Thanks for the excellent video. 👍

@dannysdiygarage Год назад

Sorry for the late response, hopefully you answered your questions by now, I’ve been traveling and haven’t had much RU-vid time, sorry

@broca246 6 месяцев назад

I normally just slacken the bolts from the subframe and pry it down a bit and the bolt comes right out. It’s less work in my opinion.

@dannysdiygarage 6 месяцев назад

Thanks for adding, appreciate the info.

@Anthony_in_Bloomington_Indiana 5 месяцев назад

Friday, February 23, 2024 ☁⛅☁ Danny, what unusual tools do I need to replace the driver side control arm? I mean tools beyond what the average, weekend mechanic has. I see a 19 millimeter wrench is part of the project. Do I also need a 3 or 4 foot long pry bar? I have a 1/2 inch, impact wrench, and an impact socket set. Thank you much and I appreciate all the work you put into making this video! I wish you a happy and productive spring, Anthony 🌳🌻🌾🐿🌳🌻🌻🌾🌳

@troudecul69 9 месяцев назад

really great video ! thanks a lot. For the front 19mm bolt of those who live in the rust belt, apply heat 🔥 🔥!! dont use a breaker bar.

@dannysdiygarage 9 месяцев назад

Great tip, I have great respect for you guys who have to deal with rust, I’ve been lucky since most of my repairs are on rust free vehicles, 👍🏼

@troudecul69 9 месяцев назад

@@dannysdiygarage respect for you for doing an excellent video with a lot of angle and good editing. The way you jacked the transmission was the best one I think. With your video my job was easier, in fact, I knew where I was going.

@dannysdiygarage 2 года назад

Yep, this job could have been so much easier with out that bolt issue

@Proxtor Год назад

This is how you know an engineers spouse cheated on them with a mechanic. Engineers design things to screw over mechanics in revenge. 😆

@dannysdiygarage Год назад

@@Proxtor not ruling it out,

@brianbroussard4433 2 года назад

HELL of an idea with the socket and pry bar widening up the brackets. I'll be doing this in a couple of weeks. Shit part is I JUST last month replaced all the motor mounts..lol.. oh well, it beats messing with that REAR mount which a MAJOR PITA!!

@dannysdiygarage 2 года назад

Thank you👍🏼

@reynaldogonzalez8209 2 года назад

Yes, they charged me $ 1,500 for labor so I decided to do it myself.

@thewishmastur 2 года назад

For both sides?

@thetuckgod9790 10 месяцев назад

Would it be convenient to just replace motor mounts if they have to be somewhat removed anyways to do this?

@aminapakzad2159 3 месяца назад

The 19mm horizontal bolt…. Mine is seized to the bushing… I managed to break it loose and unbolt it a little bit but now the bushings are causing major problems… the bolt is seized to the inner race of the bushing when I turn the bolt the rubber on the bushing twists with the bolt turning but neither my impact nor my breaker bar or my 72 ratchet are able to get the bolt to rotate past the resistance of the rubber bushings for a lack of better term…. please help

@godboat. Год назад

thank you what are the tourqe values?

@rabudman 2 года назад

I'm doing a filter and gasket change on the transmission the same day I'm installing the new control arms. Do you think you'd have enough space to pull that front bolt while the pan is removed - without removing the mounts, jacking up the transmission? Or not? Best video on this by the way.

@dannysdiygarage 2 года назад

Even with the pan removed, you still won’t have enough room, unfortunately

@rabudman 2 года назад

@@dannysdiygarage Thanks for the reply. I wasn't sure. I'm going to use your tip with the socket to open back up the space for the control arms to slide into. Great idea. Subbed.

@dannysdiygarage 2 года назад

Yep, I’ve done automotive for 30 plus years, ( if I knew then what I know now life would have been easier) thanks for commenting on this.

@mr.tarzan184 Год назад

the video very informative .....thanks

@dannysdiygarage Год назад

You’re welcome 👍🏼

@salvadoralvarez2093 2 года назад

Buen trabajo gringo gracias

@gregoriosmith6994 Год назад

The guy in Tijuana told me that he will put the labor in for the replacement of both control arms for $55.00.

@dannysdiygarage Год назад

Good deal,

@andreascaveman 2 года назад

Thanks!! Glad I found this channel! Btw - was this on a automatic transmission? Rumour says it will not be such a bolt problem on my manual...

@dannysdiygarage 2 года назад

Update the channel on this if you have a manual 👍🏼

@andreascaveman Год назад

@@dannysdiygarage seems like it's a bit too tight also, even though the oil pan is slightly smaller for manual.

@Cuyagua1765 2 года назад

May I ask you what kind of Makita impact wrench do you use? Do you feel it handled this job well? I am thinking about getting M18 FUEL GEN-3 18-Volt Lithium-Ion Brushless Cordless 1/2 in. Compact Impact Wrench with Friction Ring , but I am not sure if 250Lbs of torque will be enough for 20 years of salt collecting bolts. Thank you! Great video!

@dannysdiygarage 2 года назад

Invest in a breaker bar and use penetrating lube, I’m not sure I showed torquing everything, but I used a torque wrench

@dannysdiygarage 2 года назад

My makita is 10 years old, so whatever you purchase should be fine

@dirtyketchup Год назад

I'm looking to do this and the 4 motor mount on my '08 soon. I'm curious, with the control arm, does it need to be unload to torque those, or does it not matter? Just wondering how you would be able to manage getting the suspension under load if your jack was holding the engine/tranny out of the way.

@dannysdiygarage Год назад

Tighten everything down, put it on the ground and final step torque it,

@morganchola1009 9 месяцев назад

Wow 😮 this is wonderful.

@dannysdiygarage 9 месяцев назад

Thank you! Cheers!

@chrisryan8863 3 месяца назад

Did you replace the sway bars too Danny? The control arm kit you linked to has the sway bars with it.

@dannysdiygarage 3 месяца назад

I did not, this kit I linked to is an updated kit

@franciscommontielrodriguez707 Год назад

Gracias! great video

@dannysdiygarage Год назад

Appreciate your comment, thanks

@noahk9898 10 дней назад

Will this same process work on a 98 corolla?

@davidhoulden5791 2 года назад

I have a manual so I didn't have the transmission issue. However my front bolt reluctantly came out about 3/4 " and then stuck, couldn't get it to move with my 16" ratchet. It goes back in easily. Yes I am in the rust belt. Should I put more and more torque on the bolt? I would hate to snap it.

@dannysdiygarage 2 года назад

Use penetrating lube and let it sit, come back and screw it in a turn then back out, keep working it

@Prepare2Survive 2 года назад

I thought I read somewhere that you only need to remove the 2 left side bolts for the transmission mount and you didn't have to actually remove the entire mount. From what you remember does it seem like that would have worked?

@dannysdiygarage 2 года назад

Some times doing more can save you a lot of time, I don’t like to fight it,

@dannysdiygarage 2 года назад

I do my best

@miguelquazar883 Год назад

That is just evil to design this in a way to where you have to lift the transmission like that. It can be done, but I would prefer to do all this with more tools and equipment that I don't have. Awesome video. Thanks.

@dannysdiygarage Год назад

Appreciate your comment 👍🏼

@jp7489 Год назад

Nice👍I'm pretty sure my 2009 scion xb is gonna be the same procedure?

@dannysdiygarage Год назад

Good luck

@deedaartyst 2 года назад

Yeaaaaa, that goofy placement of trans in front of bolt!?.!?!.?! Nice vid tho

@Adrians_Ideas 2 года назад

THANK GOD I FOUND THIS

@dannysdiygarage 2 года назад

Thanks for commenting

@lechen5540 Год назад

Do you need to remove the 3 bolts at the bottom of of ball joint if you want to change both the ball joint and control arm???

@dannysdiygarage Год назад

No, but removing them makes it easier to pull off

@AmeriFanPicker 2 года назад

So what brand arms Did you use? Hard to believe the holes aren’t properly lined up. Sure you had the absolute correct part for either the arms or the ball joints???

@dannysdiygarage 2 года назад

A subscriber use Delphi brand, his comments are in this thread, he said no grinding, check it out

@AmeriFanPicker 2 года назад

@@dannysdiygarage thanks. I might go to a junkyard and practice lol. There’s a manual in one yard I might try so I don’t have to lol key with the tranny in the yard. Hell if it’s a great looking bushing maybe I’ll buy it and use it.

@AmeriFanPicker 2 года назад

@@dannysdiygarage fwiw I ended up getting duralast from autozone (OEM on forever back order and way too expensive). They were $92 each plus I had a coupon for 20% off. The ease of a walk on over the counter warranty makes it worthwhile to mei stead of having to ship a part back via rock auto etc. not that that is that big of a deal i suppose. Anyhow…the fitment was perfect on all counts. Seemed like a very quality made product. I wish I would’ve thought to weigh it against the one I took off. The passenger side was pretty hard because the front bolt was well sized into the bushing and the arm was really hard to get out. The drivers side easy peeezy. I did the front engine mount and tranny came up plenty. Blots on that side came out super easy. Anyhow….thanks for your vid it helped immensely.

@dannysdiygarage 2 года назад

Thanks for sharing this information

@dbeelee8564 Год назад

I took a look at pulling the motor mounts, so let's see if anyone has yt'd it ... and here it is. Many thanks. Btw, haynes manual describes craning the engine/trans, then dropping the K member/crossmember. What's that in dealer labor costs (book), probably over $2000+

@dannysdiygarage Год назад

There is no easy way to do it, if you have something to hold the engine up safely from the top, that is best, however most of us do it yourselfers don’t, good luck, please update us if you find a better way 👍🏼

@TheRubenjr13 Год назад

For a 2010 Corolla will it have the same bolt issue where transmission pan being in the way ?

@dannysdiygarage Год назад

Most likely it will

@limamantapachitas 7 месяцев назад

The video is 15 minutes but i guess it takes at least an hour to complete the job, any link for the parts? thank you so much for the video sir

@dannysdiygarage 7 месяцев назад

There is links in the comments if they still work

@simplyblazeegaming Год назад

Is it necessary to replace the whole LCA? or I can buy the bushings separately?

@dannysdiygarage Год назад

Great question, I don’t know that answer, the Honda dealer would be a better source to call

@johngrowney1521 2 месяца назад

Yes you can do just the bushings.

@C86913 Год назад

Does the car need to be lowered before tightening everything down?

@dannysdiygarage Год назад

Yes, that’s best

@selwyn13 2 года назад

Although it’s risky, Could we get away with cutting a small notch in the lip on the edge of the tranny Pan (maybe w/ a small cutting wheel on an angle grinder) thats in the way of the control arm bolt, so that we’ll have enough room to slide it out? That way we can avoid messing w/ loosening all the parts like the engine mount, b/c that’s what’s making me nervous as hell.

@dannysdiygarage 2 года назад

Not recommended, you’ll end up regretting it

@selwyn13 2 года назад

I’m talking about strictly on the part of the lip edge that curves down. Or even still no?

@dannysdiygarage 2 года назад

No, be very careful when working around the transmission.

@isaacsmith5611 2 года назад

Or just take out the bolt as much as possible, and then cut the bolt with a cutting wheel angle grinder, then continue to unscrew it by hand and possibly repeat until it’s out

@selwyn13 2 года назад

@@isaacsmith5611 Ohhhh. But will u have room to feed the new bolt in Frm the other side?

@dannysdiygarage 3 года назад

TOTRAIT Front Lower Control Arms w/Ball Joints Compatible with 2003-2008 Pontiac Vibe, 2000-2005 Toyota Celica, 2003-2013 Toyota Corolla, 2003-2008 Toyota Matrix. www.amazon.com/dp/B08N5VQBLG/ref=cm_sw_r_cp_api_glt_fabc_V9JNR7EM8AYE6AM9RF4A?_encoding=UTF8&psc=1

@salvadoralvarez2093 2 года назад

Where did you buy the griner??

@dannysdiygarage 2 года назад

Sorry I missed this comment, harbor freight, 20 bucks

@claytonjh1223 Год назад

what model makita impact are you using?

@dannysdiygarage Год назад

My makita tools are at least 10 years old, anything you buy today will be better than what I have, however I’m a big Makita fan, that’s my brand

@Thunder_Dome45 Год назад

Jeez have to take 30% of the car apart to get a bolt out. I wonder if they design that on purpose?

@dannysdiygarage Год назад

They weren’t thinking of the DIYer, that for sure

@thepawchoe2749 2 года назад

I don't see the sway bar. Did you remove it? I am currently doing the same repair, but I feel like the sway bar is in the way.

@dannysdiygarage 2 года назад

I don’t remember removing that, it’s been 1 year, however I showed ever step

@thepawchoe2749 2 года назад

@@dannysdiygarage it is a corolla, yes?

@thepawchoe2749 2 года назад

I just noticed the reason your CAs are so trashed is because of the lack of a sway bar. Mine is a 98 and i didn't really have to replace the CAs despite them being originals because mine has a sway bar to absorb half the shock. I'm actually doing the second one right now and it's also still in decente shape. I just want to do it because I'm reolacing every other suspensión component anyway

@dannysdiygarage 2 года назад

Thanks for the information, makes sense

@thepawchoe2749 2 года назад

Psh. I'm thanking you, brother. Disengaging motor Mouns is easier than the subframe. Screw that nonsense lol. Anyway, I appreciate your help and feedback. God bless.

@maelrodder9091 2 года назад

What brands are those control arm? Delphi?

@dannysdiygarage 2 года назад

I’m sure it’s a overseas brand, but works fine TOTRAIT Front Lower Control Arms w/Ball Joints Compatible with 2003-2008 Pontiac Vibe, 2000-2005 Toyota Celica, 2003-2013 Toyota Corolla, 2003-2008 Toyota Matrix.

@maelrodder9091 2 года назад

@@dannysdiygarage I’m asking because I don’t have a rotary drill like you to widen the holes for the ball joint . I bought my control arms from Delphi so hopefully it will fit right in. I also notice you didn’t torqued down the bolt that goes across the control arm on the left side. Good video overall

@dannysdiygarage 2 года назад

Let me know the outcome, I love to know if they fit

@maelrodder9091 2 года назад

hey I’ve replaced both side with Delphi control arm and they fit perfectly with no problem at all I didn’t have to do any modification on the control arms they were exactly the same as the OEM my car came with and by the way the Torque Spec is 101 ft-lbs you gotta torque those bolts down baby

@dannysdiygarage 2 года назад

Can you share the link to purchase these and I’ll post it, this will help others, thanks for sharing

@michaelgriffin3369 Год назад

Can you cut the bolt and install a new one the other way?

@dannysdiygarage Год назад

No, it only goes in one way, just do it as per the video, it’s not that difficult 👍🏼

@michaelgriffin3369 Год назад

@@dannysdiygarage thanks for the info & the great video. I’m just scared of the motor mounts. I know what you meant when you said you were lucky they lined up. Lining those up has been a nightmare for me before because my jack isn’t good at delicate moves.

@Musang_Jebat Год назад

👍👍👍

@arcticgummibear4500 Год назад

What year is your Corolla?

@dannysdiygarage Год назад

This is 2005 automatic LE

@BrianAhearn8597 2 года назад

If he had Taken the bolts out of the ball joint that pickle fork was not needed

@JshMusician 7 месяцев назад

No mention of torque specs. So important but no one mentions them when doing these car videos.

@dannysdiygarage 7 месяцев назад

Torque specs are in the description on part 1 or 2, I’ve started adding torque specifications on my latest videos, sorry about that, live and learn ❤️

@David-gu8hv 2 года назад

How long does it take?

@dannysdiygarage 2 года назад

Right side goes pretty quick, 2hours Left 4 hours, I’m assuming no real experience doing this, if you have experience left right side 1 hour left side 2hours, it took me all day with filming and filming takes a lot of time

@dannysdiygarage 2 года назад

If I did this job again now that I’ve done it 3hours, it’s actually pretty easy start with the right side

@David-gu8hv 2 года назад

@@dannysdiygarage thanks!

@JoseMorales-nf7jd Год назад

👍

@eduardoelena6264 Год назад

I couldn’t breaks loose the bold behind the transmission 😢

@dannysdiygarage Год назад

Bummer, squirt a lot of penetration lube on it, let it sit and try again

@ImAlwaysRightjustaskgoogle 9 месяцев назад

ok no you dont have to grind your control arm wtf are you doing? you insert the balljoint slightly , start the off bolt, then install the nuts and run them down for a tight fit...its like this for a reason, and do not spread your mounts for the lower control arm, place the control arm big bushing in first, use rubber mallet to work the barrel businng in , its easy, you want the pinch point pressure they way it supposed to be to get a good torque on them bolts , fyi the torque is not great enough to pinch what you seperated.... WARNING!!!!! DO NOT INSTALL YOUR SUSPENSION PARTS LIKE THIS OR YOU WILL RUN INTO ISSUES, SMH PLEASE DONT FOLLOW THIS GUYS "ADVICE"

@dannysdiygarage 9 месяцев назад

MrJames: Maybe you can make a video to show others how you do it👍🏼

@selwyn13 2 года назад

Erggg. 😠 Damn it Toyota