No video :(

TPLINK CPE210 / 220/ 510 / 610 Access Point and Client Complete Setup

Подписаться 6 тыс.

Просмотров 82 тыс.

50% 1

#AccessPoint
#TPLink
If you find this video helpful,
Donation accepted at any amount.
GCASH 09167555337
You may want to have internet access for your nearby farm house to monitor CCTV, or control SMART SWITCH for generator or equipment, refill water for pets, or enjoy browsing while you're with your work away from home where fiber line is not available. Access Point answer this. So here's the simple and complete set-up and configuration. Remember to attach Router at the CLIENT CPE for WIFI Access..
Needed equipment:
2PCS pair
TPLINK CPE210 or CPE510
2PCS CAT6 OUTDOOR LAN CABLE needed to connect adapter to CPE
2PCS INDOOR CAT6 LAN CABLE needed to connect router to adapter.
TAKE NOTE: Router must be attached at the CLIENT CPE Power Adapter LAN PORT to enjoy browsing the internet
CPE210 Range tested: Best Performance if less that 1000m distance from the Access Point
If distance is more than 1km, it is better to use CPE510
You cannot use CPE210 and match with CPE510
You must use same frequency CPE, means if you use CPE210 as Access Point, then your Client must be CPE210

Опубликовано:

29 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 130

@vaskasooo9469 2 года назад

the best explanation thank you .

@wooduplaytimber 2 года назад

This was a great video to follow. My distance is just under 100 metres, but your video was by far the easiest to follow.

@leifpurvis4826 5 месяцев назад

This was a life saver. Went seamlessly until I forgot a password at the very end. I got back on track with client, and all panned out. THANK YOU!!!

@johnny-smith 5 месяцев назад

Thanks, no one else said to change the Client computer’s IP back to automatic

@juntrinidad6574 2 года назад

Laking tipid dahil dito naipasa ko ang internet 3km away.. Salamat

@vaniljdrommen Год назад

Thank you! Id had trouble with these for 3years. And now its finally working 😍

@FAIROOZBANNAPK 2 года назад

Superb, Thanks buddy... Very easy setps I have done my work by your tutorial...

@ooruthendy6502 2 года назад

perfect video for cpe setup from A to Z

@Bang-Ben_Tutorial Год назад

thank you very much "CoolRider"..I use wireless TP-Link CPE210,,speed until 300Mbps it's very good 👍

@iceicepogi Год назад

Pls do visit my channel watch videos and ads to support me if you have time. Thank you in advance

@abbasversi1058 5 месяцев назад

Made life easy, great assist 👍

@bettylovell173 Год назад

simply the best by far thanks

@fvpvideos94 2 года назад

The Best ang explanation mo sir. Thank you. How about sa client na router sir Kung cpe510 gagamitin need po ba na 5g yung router?

@iceicepogi 2 года назад

Kahit 2.4ghz or dual 2.4 / 5ghz pwde

@mohamedaberghaze4575 11 месяцев назад

I did all the steps and it worked. Thank you. Just a question please, the distance separating the two devices is approximately 400 meters. The signal he picked up is 50%. Is it good or should I try to answer 70 or 80%?

@iceicepogi 11 месяцев назад

At 400m you should get full signal bar if no objects in line of sight. Check your line of sight between your cpe again..

@jotburke7749 2 года назад

All I would suggest is that you make backups of both the Access Point & Client configurations. Otherwise one of the most concise videos ... Thank you!

@iceicepogi 2 года назад

yes all my cpe have thier own config file.. Pretty good idea

@geirellingsen4498 Год назад

Thank you so much for a very easy to follow video. I have MacBook and use MacOs. I have a couple questions: Both devices are configured and set up, but there is no internet connection between them. Where have I done wrong? Does the device have to be connected by cable every time a change needs to be made, or is it possible to do it online without a cable? Answer will be appreciated.

@iceicepogi Год назад

You need to connect AP(the 1st CPE configured in the video)to your ISP router. Then the last (client) CPE connect to your new router this will be the one to distribute internet

@wazzuu08 28 дней назад

Helo. Planning to setup access point from one house to opposite house 10m away. So need 2 CPE correct ?

@ericvonflorendo4752 2 года назад

thankyou natapos ko din yung proj ko salamat po

@iceicepogi 2 года назад

Enjoy po..

@noelkjonstad8446 Год назад

this may be a stupid question but can i connect wirelessly to the Client (eg. via a wireless camera) or do I need another router connected via ethernet cable to the client.

@iceicepogi Год назад

If you set as AP then check configuration of your camera if it can detect wifi..

@eal1 Год назад

I set it up via another router connected to the client I'm using the 710 5G version and have some devices that will only take 2.4. I could never find the client as a wifi network only the AP one but seems CoolRider is possibly suggesting you can have an AP to AP configuration?

@StefanOlofsson-tn2ux Год назад

Thanks, best ever!

@gurpreetchandi4849 Год назад

Thanks sir very helpful video

@KBHSharingChannel 2 года назад

Thank you bro

@owensteve9483 Год назад

Question is it possible to make 2 separate nanostation but all are in one location broadcast one Access point as if it was one nanostation?

@robertraman6307 2 года назад

Hello, nice video! I wonder - I need help with my setup. Is this correct? Internetmodem -> router -> CPE210 access point -> CPE210 client -> Ubiquiti LR Access point -> Wifi connection to my computer, phone, appleTV. The router where the internet connection is could route the connection through this setup?

@robertraman6307 2 года назад

I want to share internet from one house to another house 500 m away, not only have one connection but multiple? Or do I need a router to create new ip-adress in the distant location and have that connected in between? internetmodem -> router -> CPE210 access point -> CPE210 client -> router - > Ubiquiti LR Access point -> wife connection to devices?

@sanchalak684 7 месяцев назад

Great job

@hacaz8567 2 года назад

Muchas gracias, perfecto

@albertosteffanini2615 2 года назад

Hello! nice video ... I bought it after seeing you .. but a question: on the instructions that serve the grounding for the antenna .. did I understand correctly? a good shielded ethernet cable is not enough? !!

@iceicepogi 2 года назад

You may add grounding wire thats theoretically effective. But lightning wont spare anything if it will directly hit by it. Tried once my cpe directly hit by lightning, both cpe and router dead instantly. To sum up, grounding not that really effective.

@Deleonaircraft956 2 года назад

Does this work for 220 bridges

@johnny-smith 5 месяцев назад

Anyone know why it’s limited to 100 down despite using Cat 6 cables and having 700+ down from the modem?

@multihaydrainfinity8876 7 месяцев назад

Thank you❤ . What is the provider's speed and the customer's speed up to 1km?

@iceicepogi 7 месяцев назад

You can get same speed. Thats very short distance

@kentdextermarcos5458 Год назад

Sir okay lang ba iisa lang yung CPE? kasi medyo kapos pa sa budget. I mean, Modem (Converge) > CPE (AP) > Router (tenda). Bali yung tenda na yung mag rereceive and nasa 250m po yung layo.

@iceicepogi Год назад

Pwede naman siguro kung kaya ng signal sir try nyo po..

@hillhavenleonbergersleonberger 2 года назад

thanks so much great job

@ByahingJoPH 2 года назад

napunta ako dito dahil sa shopee..hahaha

@iceicepogi 2 года назад

Yes shopee din ako kumuha

@ByahingJoPH 2 года назад

@@iceicepogi ilang kilometers aabot sir

@iceicepogi 2 года назад

@@ByahingJoPH CPE210 medyo hirap na sa 1km nung nag test ako marami matataas na kahoy, i think kulang sa height ang pole ko. Pag lampas 1km mas maganda CPE510 kana mas reliable, kunti lang naman dagdag sa presyo

@modefour4 Год назад

Hi. To test alignment / signal strength when the Client and the AP are up so high did you need to have a long cable to the CPE or were you connected to the CPE via wifi?

@iceicepogi Год назад

you can use your phone once CPE is connected to the router. just manually set ip addfess of your phone

@CesarHernandez-wv6jh Год назад

Perfect

@blacklneer58 6 месяцев назад

Thx so much

@sportindaveyg 11 месяцев назад

Darn wondering why my Access Point isnt showing in the Client Configuration part... hmmm

@_matis_ Год назад

Does the first unit need to be physically connected to the router of my ISP? Let us say my ISP router is downstairs and the unit is upstairs. Can't they communicate wireless? I would need a long cable and holes in the walls

@iceicepogi Год назад

It cannot communicate wirelessly if the setup is like in the video. You need to connect router via lan cable.

@_matis_ Год назад

@@iceicepogi Thank you

@amazeme_ 8 месяцев назад

Boss pwede pagawa tutorial paano mag config ng Multi AP isang EAP 110 at CPE210. TY

@iceicepogi 8 месяцев назад

Eap110 pwede multi AP sya. Pati CPE210 pwde din multi AP

@Yeshinfotech Год назад

I recently installed cpe210 AP and client but internet dropped completely frequently even if Tx and RX signal showing. Can you please help me?

@iceicepogi Год назад

Make sure of the line of sight

@jaouadloutfi6450 2 года назад

Thank you

@jignesh318 Год назад

I have 210 and UBNT loco m2. 210 is a AP and loco M2 is client. But i am having a problem to connect AP. From client side i can see AP in. Site survey but I am not able to connect it. Please advise

@iceicepogi Год назад

Make sure they have the same frequency. 210 is 2.4ghz

@faizalesa89 Год назад

Can the receiver unit then connected to wifi router so that at the receiver house can get wireless Internet?

@iceicepogi Год назад

Yes you can connect to wifi router (client or known as reciever) as intended function. Just make sure that the AP is connected too to the main isp router

@Networkgaming01 Год назад

Sir after finishing configuring client cpe can i disconnected the lan line from pc??? Ans me please I want to learn how to setup this device with pc and phone......

@iceicepogi Год назад

Yes disconnect it, then connect AP LAN to Router that is connected to the internet. Connect LAN Client CPE to router then enjoy the internet..

@matcense529 Год назад

is this an omni directional or directional connectivity

@osamakhatib8501 Год назад

Hello, Does it support multiple subnets?

@clarkboocclaridad2993 Год назад

boss hindi ba maglalagay ng distance settings sa sender/Ap? naka zero lang kasi DISTANCE SETTINGS. samantala sa RECEIVER/client nilagyan mo ng 1Km.

@iceicepogi Год назад

Automatic yan sir basta nag bind na yang dalawa..

@kokmantam204 Год назад

I follow all your step,but when I connect the access point to ISP,it's still can't internet

@iceicepogi Год назад

What model do you use for AP and Client?

@kokmantam204 Год назад

@@iceicepogi CPE210

@andrewtv9887 10 месяцев назад

Boss pede ko ba i hide ssid ni AP,. May 10 stations na connected. Hindi ba maapektuhan mga ito sir pag naghide ako ssid ni AP

@iceicepogi 9 месяцев назад

Pwde mo i hide AP

@edvinas4072 Год назад

I want to have extended wifi to my garage, I have 2 of cpe210, how I need configure it to have extendef wifi? Can it work if first cpe210 i config like AP, second one config as repeater, and from repeater I can connect wifi?

@iceicepogi Год назад

You should configure as AP and Client as shown in this video. You need router in Client CPE.

@edvinas4072 Год назад

@@iceicepogi so from client I must have LAN to router? Because I have router In my house, garage is 50 meeters from house, wifi to weak, so I need connect thes two cpe as in video, one cpe210 connectet to my main router in house and i install it outside house wall with lan cabel, then second cpe client i install on garage wall outside, then from client cpe i need conned LAN cabel to SECOND router in my garage? And from this router i can have wifi, do i understood right?

@iceicepogi Год назад

@@edvinas4072 you got it right!

@mib0xsalvad0r10 2 года назад

Hello sir ung pnkta mong speedtest ano jto during setup ba or nung nakasetup n s malayo ung client ?

@iceicepogi 2 года назад

Nung malayo na sir. Basta maganda signal quality nya, mabilis ang speed..

@dmhans22 Год назад

Sir possible po ba iconnect ang cpe510 sa cpe605 for p2p? 500m lang po distance ng dalawa..

@iceicepogi Год назад

Pwede pwde. 500m napakalapit lang

@alilou-belghit 2 года назад

I have one TP-link Cpe 510 . in client mode it is possible to connect to any wifi network or only to another tp-link cpe 510 ?

@iceicepogi 2 года назад

Yes. It is better if you pair it with the same CPE. Ordinary wifi function well with wifi gadgets. CPE is created to pair with CPE. It is better if you have another CPE. All you need to do is to configure AP mode so your client can work with it..

@citizenoftheworld11 2 года назад

i think if u comnect ur cpe to another wifi other than another cpe's u won't get the long distance i will be used as a wifi adapter but i should have some good range

@glem9582 2 года назад

If I connect the client to a router do I need to reconfigure the client? or no need?

@iceicepogi 2 года назад

Here's diagram.. Configure AP CPE, Configure Client CPE, Connect router.. Configuration is once only..

@ronaldiroy26 2 года назад

Good im trying to configure cpe510 in AP ROUTER mode, pero pag mag click na ako sa AP ROUTER mode may warning message na ganito "the status of Port0 will change to WAN, and the management access will be disabled on this port. If you want to managr the cpe device through Port0, go to MANAGEMENT>Web server to configure the Remote Login IP Address" Paano ito ma solve, mas preferred ko kasi AP ROUTER mode to control download and upload speed ng client

@iceicepogi 2 года назад

Pa send screenshot Messenger sir sa E-Link Rosario para ma check ko..

@zourdanyoussef7148 Год назад

If the distance is just 300 m can just use one

@sksaifuddin2304 2 года назад

DHCP SHOULD BE ON OR NOT?

@naadinarembellammotivation7385 8 месяцев назад

only three lights lighting in client cpe what to do

@iceicepogi 8 месяцев назад

Re align and monitor connection signal

@naadinarembellammotivation7385 8 месяцев назад

@@iceicepogi re align the antenna or what to realign

@notsolonelyrider2548 2 года назад

sir kung naka ap mode ang base station pwede ba madaming client na cpe kumonek?

@iceicepogi 2 года назад

Pwede sir..

@Firstimpressionofmy 2 года назад

Hi, I'm facing the issue of "failure to get data" Have you any idea about it?

@iceicepogi Год назад

Make sure ap and client have good line of sight

@rinchintsering7863 2 года назад

Do I require internet connection in the laptop for configuration?

@iceicepogi 2 года назад

It is not required since you only configure the two device to exchange data with each other. Once done then you can connect the internet to the AP

@ralphpianar9029 11 месяцев назад

idol paano lagyan ng pisowifi ang receiver side? Ganyan ksi na setup gusto ko pero dagdagan ko vendo

@iceicepogi 11 месяцев назад

Gamitan lang ng router tas ikabit mo na sa piso wifi client mo

@leomar.gumapac Год назад

Paano po setup cpe210 sa vlan? Di ko po masave yung vlan settings sa network vlan management

@iceicepogi Год назад

May i know kung paaano hardware setup nyo sir? Haven't tried aa vlan. Although may vlan ako nakita sa portal nya, try nyo lang tignan.

@martiruiz Год назад

Is it compatible with starlink?

@iceicepogi Год назад

It should be. Because all routers are standardized to adapt other equipment such as these cpe to work together.

@chronus117 2 года назад

Kung mga 150m lang walang line of sight ano pwedeng gamitin?

@iceicepogi 2 года назад

Mas maganda mag FOC ka na lang pag wala LOS.

@freefree8047 2 года назад

Good day sir, is this set up compatible for omada piso wifi voucher type?

@iceicepogi 2 года назад

Yes fully compatibe with omada and eap.

@freefree8047 2 года назад

Thank you po sir. Sa client side po ay need pa ba maglagay ng EAP for access point or hindi na po?

@iceicepogi 2 года назад

@@freefree8047 Yes need po maglagay ng eap client side para sya ang mag distribute ng wifi signal. I think parang ganito po sya: Client Cpe510-Router-Omada Controller-Eap