Transgo Shift Kit Installation 45RFE/545RFE-Part 1

Подписаться 1,5 тыс.

Просмотров 67 тыс.

50% 1

After coming up empty handed after looking for clear instructions on how to install a shift kit in this transmission, I decided this would be the perfect opportunity to make this video. This is the Trans-Go 45rfe-HD2 kit and it works on the 45rfe,545rfe, and 68rfe. These transmissions are found in many different vehicles such as the Dodge Ram,Jeep Grand Cherokee, Dodge Durango, and Dodge Dakota. These transmissions are used behind the 4.7l V8, 5.7l hemi, and the 6.7l Cummins. I am installing this kit in a 2002 Dodge Dakota. This video may also goes through the steps to replace the solenoid pack in these transmissions which is the most common problem if you get transmission codes.

Авто/Мото

Опубликовано:

25 янв 2014

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@3347861 6 лет назад

Accumulator springs simply cushion the shift. Stiffer springs equal a firmer shift, and the thicker plate holds the higher spring pressure without distorting. I'm running this kit and love it.

@leebar342 9 лет назад

Good job and saved me some guess work! My Durango is an '02 4.7 4x4 with 197,000 miles. The trans was not shifting into 2nd or 3rd all the way, on occasion, and this kit is highly recommended. I hope it does the job and will find out today. FYI, Rock Auto has a replacement oil pan with a drain plug for this trans.

@jrstone257 6 лет назад

Thanks for posting this. Ordering the trango kit to solve my 2nd to 3rd problem. Plate screws came out in the pan and plate was bent.

@klmelj 10 лет назад

I just purchased a transgo kit yesterday and the first thing I was going to do it shoot a video. Looks like you took a good video. I will probably do the snap ring and the trans pump spring upgrades too.

@Internetpirate3 10 лет назад

The only thing I wish I had shown in this video was how to unplug the electrical connector but for the most part I tried to make this video as informative as possible. Good luck with your trans!

@edoscar83 Год назад

Hello. I like your video. I have a 5-45RFE and plan to install the Shift kit. But I have seen some change the pistons. What do you think?

@rossokeefe9268 2 года назад

Hi..my transmission In 09 ram sometimes stays in 4th gear..would this kit help that out...last time I changed the fluid my truck ,it somehow gave it tire ripping power..lasted for maybe 6 months but went soggy again..it still drives fine...would this kit benefit me with that issue as well?

@markvietti 5 лет назад

I did not notice any difference after installing this shift kit.

@eportillomx 9 лет назад

changing the transmission solenoid pack will fix my neutral safety switch or reverse safety switch problem? (they are the same ,aren't they?)

@DeezNutz-cw7dc 7 лет назад

yes, im fixing this now.

@1eldar777 4 года назад

No 3rd and 4 gear can you help me out with it

@testdepth377 29 дней назад

What is the reason for installing this kit? What does it fix or repair?

@futbolero4152 10 лет назад

how did you know that your shift kit needed replacement? i have tge same transmission and after a throughral atf change with new filters, the car will shift, but wont move. did this happen in your car? mant thanx and great video

@Internetpirate3 10 лет назад

Check the fluid level and check to make sure you have the flat filter seated correctly. Also make sure that when you install the new seal for the flat filter you have to tap it in with a hammer or it will leak and your car won't move.

@user-dr1ez1yr3u 3 года назад

Sounds like your seal on the flat filter hasn't seated all the way. I've seen it in this transmission many times.

@michellescott2400 7 лет назад

Where does spring go

@lassestorgards7153 6 лет назад

Hi I have a dodge dakota with a 545rfe transmission. The problem is that it stalls when I put it in gear but it works in reverse. I changed the shift solenoid but it didn´t help. Is the torque converter lock up somehow any clues of what part it make it to fail.

@Internetpirate3 6 лет назад

Do you have any codes stored in the TCM or is the Check Engine light on?

@lassestorgards7153 6 лет назад

p0700 p0456 p0442

@WaknBakn 5 лет назад

I'm thinking about doing this to my 2011 ram and I dont have a tuner. I plan on getting one later, is it hard to remove the resistor later?

@Internetpirate3 5 лет назад

It should be pretty easy to remove the resistor later on. Just when you install it you can use a spade connector in the wiring harness to attach the resistor temporarily.

@WaknBakn 5 лет назад

@@Internetpirate3thanks so much for the reply. I didn't notice that the video was so old until after I posted. Does the resistor get connected in the fuse box? Again thank you for replying

@Internetpirate3 5 лет назад

Connect the resistor inline with the wiring harness preferably at the solenold pack connector.

@CHAOSMOVEMENT 2 года назад

I know this is an old video, but what were you doing at the end of part 1? It looked as though you were getting ready to change that little valve, and you were messing with some kind of tool but I have no idea what it was, and in part 2 it looks like you were already done with it.

@Internetpirate3 2 года назад

It was an old hard drive magnet. The valve is steel and the VB is aluminum so pulled the valve out easier.

@CHAOSMOVEMENT 2 года назад

@@Internetpirate3 Nice, so when you got it out you just coated in ATF and put the new ones back in? Was there any trick to that or do they just slide in and that's it?

@Internetpirate3 2 года назад

@@CHAOSMOVEMENT Yep just do that. If it doesnt just slide in theres trash in the bore and will need to be sprayed out with brake cleaner

@CHAOSMOVEMENT 2 года назад

@@Internetpirate3 Sweet, much appreciated video and responses. Know that your efforts made a huge difference in my life right now.