Traxxas Revo 3.3 Turning the needles to basic factory setting Nitro Engine dont start

Подписаться 8 тыс.

Просмотров 44 тыс.

50% 1

RC USA 201 and RC KING KONG. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RC KING KONG and RC USA 201
#revo3.3 #tningrevo3.3 #nitroengine #revo3.3nitroengine, #nitrorevodontstart #revo3.3basesetting #nitroenginebasicneedlesetting

Развлечения

Опубликовано:

28 сен 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 49

@PaulSingh-dz1sn 10 часов назад

You saved me thanks man I taught adjusting the trottel linkage will fix my high idel and overheating overall but when I slapped this setting on my t maxx it was running really crisp and clean came un clutch thank

@gongora420 10 месяцев назад

Thank you sir I did exactly what you said it’s running like a champ. I got a Traxxas slayer off of one of my friends he sold it to me pretty cheap only 200 bucks. He said he havent ran it in two years. I replaced the spur gear. The slipper clutch after watching your video. She fired right up cant believe how good it’s running.

@rcusa201 10 месяцев назад

Nice job

@RADARPOLAND23 Год назад

You are the man dude thank you so much couldn’t get mine to start and run properly to do the break in they say it’s rt r/break in out of the box and everything was all funky I appreciate it man! Now it runs good and I can finally break mine in.

@carstenl87 Год назад

Great video, only one I have seen where they tell the exact starting position for the Low Speed Needle! I used this video earlier today to reset my Revo settings and get it running again! Worked like a charm! I only had to do some minor adjustments to lower the idle a bit, and richen the High Speed Needle half a turn, due to my 25% nitro fuel

@rcusa201 Год назад

Nice job!!! It always worked for me

@demosthenes1 5 месяцев назад

Thanks I been looking to buy one of these for a long time but always felt like it would be hard to deal with. Saving this video for future reference.

@greenie43 Месяц назад

Great job, bro!! Came in handy!! 😎👍

@eyeintheskiesdavid9277 5 месяцев назад

Thanks for the good tips on how to set the high and low speed needles only bought the traxxas slayer pro 4x4 yesterday and can't wait to get it out for a spin thanks to you bud big thanks and a big like from me bud 👍🤝

@Azer831 3 месяца назад

Thank you boss! I got my jato back and running!

@rcusa201 2 месяца назад

Nice job!

@douglikins2326 Год назад

Thx for the ni e video got one bearly used and is to rich and now i have a hood place to start

@noneyobuisness8789 Год назад

Video was so perfect I had to subscribe lol 👍🏾👍🏾👍🏾🤣🔥🔥🔥I have mines “lo

@user-jz5gj9zq5p 11 месяцев назад

I blew my first plug barely running it still new finally got it to shift if this video and one other but now I think I'm a bit rich or lean not sure assuming to much fuel cuz I got alot of drips that come from exhaust drips not alot but not sure what's best

@damonbridgmon7199 7 месяцев назад

I have a 2.5r....it sat for over like 10 years. It will run but im thinking the rings are bad on the piston.. onky runs for about 10mins and than replace glow plug.. think its junk or need better tuning? Freaking glow plugs are to much for 10mins

@rcusa201 6 месяцев назад

I think this is junk

@damonbridgmon7199 6 месяцев назад

@rcusa201 agreed got a 3.3 otw

@user-jz5gj9zq5p 11 месяцев назад

Boss man whats best glo plugs for 20 percent nitro for the revo 3.3

@rcusa201 11 месяцев назад

I still with stock

@ironhead320 4 месяца назад

What is the throttle and brake servo you running I see there different ones in different revo's

@rcusa201 2 месяца назад

Stock

@dustinplee5067 Год назад

This video will help me out when I get a 3.3 engine but I have a question can you please make a video on tuning a .15 and the .18 and .16 and I think there’s a .15 sh engine I bought a nitro stampede vintage four or five years ago and could never keep it running so it just sits on the shelf and I don’t know how to turn it but. If you could make them videos on tuning them engines that would help me a lot thanks

@rcusa201 Год назад

Sun have those

@dustinplee5067 Год назад

@@rcusa201 what do you mean

@williedoit3381 Год назад

Where do the double a batteries go for the controller to control the wheels?

@rcusa201 Год назад

The what

@williedoit3381 Год назад

@@rcusa201 I'm sorry. Never mind. I found out the model Revo I have, has a recharge port at the bottom of the frame. I have to order a charging cord to charge my Revo so that the receiver will control the wheels. If that makes any sense at all to you, I'm just getting into this hobby

@williedoit3381 Год назад

@@rcusa201 thank you for responding

@earlgraves5568 Год назад

How do I know when the idle gap is .7- 1.0 mm gap

@earlgraves5568 Год назад

@@williedoit3381 I mean I thought it was right but my idle screw is all the way down to where it won’t go further but it looks like that

@ironhead320 3 месяца назад

I though i.cooked my engine here the bearings lock up in the clutch bell burnt up 2 clutches

@MasterTakos 7 месяцев назад

What kind of rc is this i have the same model but cant find the parts manuel

@rcusa201 7 месяцев назад

Traxxas Revo 3.3

@ironhead320 4 месяца назад

I got a new 3.3 engine the low speed was at 1.5 factory.

@rcusa201 4 месяца назад

Ok I’ll try that

@ironhead320 3 месяца назад

@@rcusa201had my high side at 3 turns out and it was gurgling to rich right now I'm at 2 out and still playing with it

@ngirardo86 5 месяцев назад

What are you showing other than your idle is WAY too high

@laurensandoval2796 Год назад

Mine NEVER starts that easily 😢

@rcusa201 Год назад

Retune it

@gforce_117 Год назад

Good fuel, good glow plug, and a good carb setup (needle base settings to start, no air leaks, etc) it’ll start every time. Set idle gap and turn low speed to achieve idle.