Тёмный

TRAXXAS TRX3.3 nitro engine factor needle setting 100% nitro engine will start up 

RC USA 201
Подписаться 8 тыс.
Просмотров 3,3 тыс.
50% 1

RC USA 201 and RC KING KONG. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RC KING KONG and RC USA 201
#nitro #engine #startup #trx3.3 #traxxas3.3nitroengine #nitroenginedontstart #needlesettingfornitroengine #nitroenginestartup #nitroenginedontstart #startupnitroengine #factorneedlesettingfornitroengine

Развлечения

Опубликовано:

 

16 янв 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 19   
@ironhead320
@ironhead320 3 месяца назад
Even with a 1mm gap still idle high and kind wants to roll forward
@check-mate412
@check-mate412 2 месяца назад
Same problem
@FalconWing1813
@FalconWing1813 Месяц назад
@@check-mate412 On the traxxas web site it says the idle gap can be between 0.7~1.0 mm. So you could go down. If its still high you may need to richen the needle abit.
@jakehughes-mt4fj
@jakehughes-mt4fj Год назад
Going to set back to factory settings once I rebuild my engine!
@rc2318
@rc2318 Год назад
Good video 🎉
@ronfuller1256
@ronfuller1256 Год назад
Very good video!
@1arrays
@1arrays 29 дней назад
i think i broke my idle gap needle it wont move when i screw it in or out it wont fully stop like stripped screw
@rcusa201
@rcusa201 29 дней назад
Uh ohh
@nickstone1905
@nickstone1905 2 месяца назад
I broke truck in was snappie i went to tune pinch test 3 sec i tune hsn and lsn and i touched ldel screw not no matter what pinch test cut out over 7 secs
@rcusa201
@rcusa201 2 месяца назад
Keep tuning it will get there
@eyeintheskiesdavid9277
@eyeintheskiesdavid9277 4 месяца назад
You helped me out big time I only bought a traxxas slayer pro 4x4 with out a ezay starter for 200euro it looks brand new don't even think it was broken in is there any way to tell it was broken in before as I can't wait to get it out for a spin thanks for sharing big like from me bud 🤝
@rcusa201
@rcusa201 4 месяца назад
Cool np!!
@harrisonmaxwell4480
@harrisonmaxwell4480 Год назад
Just got me a revo and have it tuned pretty decent but what causes the wobwob hesitation at higher throttle
@rcusa201
@rcusa201 Год назад
Could be bad tuning too lean
@ironhead320
@ironhead320 3 месяца назад
Do you use a temp gun and what temps you running at
@rcusa201
@rcusa201 2 месяца назад
Nope
@ironhead320
@ironhead320 Год назад
Can you put a.sh.28 engine in the revo
@rcusa201
@rcusa201 Год назад
Yes but u might have to do some fabrication modification cut here and there and file engine base to make it fit
@ironhead320
@ironhead320 Год назад
@@rcusa201 that's what I thought
Далее
Traxxas REVO 3.3 nitro engine rebuild TRX3.3
32:51
Просмотров 7 тыс.
Traxxas Revo 3.3 Full Brushless Conversion Guide
20:13