Tune Up Your Table Saw 

This is a fantastic video. No extra talking, just the facts, at a decent pace, with great camera angles.

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice ru-vid.comUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

This is the best overall table saw tune up video I’ve found. It is exactly what I needed after taking my Craftsman saw apart to change the bearings. Thank you!

How lucky am I? I have the T2424 1 Rigid in this video. I had NO idea the blade stops were adjustable from the top. Thanks. and... never lose the paneling in your shop I love it.

Wow…. I soooooo needed this. This video is amazing and just what I needed. THANK YOU!!

I am so glad you made this video and showed theres a super simple way to adjust the saw stop. My saw was sitting a good 1/8 of an inch off and I couldnt figure out how to correct it. Thank you!

@kfholler Definitely check the rip fence and table miter slots for parallelism with the blade, since older table saws often have inaccurate rip fences. Also, make sure the power cord is in good condition without cracks in the insulation or other obvious nicks or damage. Start with a scrap piece for those first few cuts. Use the cut pieces as feedback for how the saw is operating (binding, burn marks or excessive blade marks on the cut edges, etc) and tune it up from there based on the results.

Good video on table saw maintenance.... with the exception of the illegal possession and use of the Adohr's and Southland Corporation Dairy cases.

Thank you for the informative video.

I have a similar Ridgid table saw and this video made me confident to tune it up. I managed to clean it nicely without tilting the saw though. I did unscrew all six bolts for front and rear trunnion before making adjustments though ( in the video the author just loosened three rear trunnion screws). Thank you for the great and easy to understand video. Now I have a fine tuned saw.

Thank you so much! I have had the same Ridgid saw for years and could never get it to cut square. Five minutes of work fixed years of frustration.

Thank You so much for taking the time to make and post this video! A lot of really helpful info!

Excellent video. Very clear. Also love this table saw

I bought a used 3hp craftsmen about 10 years ago and went through this I think I better do it again thanks for the reminder

I am shocked that a Table saw tune up is necessary! I have always believed that the power tool fairy visited my shop periodically, and worked his magic (although I admit that performance has gone south). Seriously, thanks for a most informative and eye-opening posting.

I have the TS2424, owned it since new 15 years, it runs great made in USA! I have only adjusted the table parallel to the blade 2 times and stays right on the mark. The dry lube spray works great on the rack screw adjustments and wax the cast iron top. It still looks new and is very accurate. I am not sure where they are made now? China seems to be sucking the life out of all woodworking equipment and tools. Thanks for the video!

EXCELLENT VIDEO. It was really nice to see this video because I have the exact same Ridgid saw. It has been a super saw ever since I purchased it new in 1995. The saw seen at least 15 heavy moves and storage scenarios where movers thought it was just a heavy thing to bang around and only now has the tilt gone off, and only by a very narrow margin. However, if your a woodworker then OCD is not a bad thing to have. ;) and so I am now about to adjust that issue. As for those folks that had a bad experience, well as all things in life, some people will have a good experience and some won't. Again, great video for this saw.

Finally, a professional video.

Great video... I think some professionals forget that there are some novice and beginners woodworkers out there. From setting the measuring tape on the fence to the blade to leveling the throat plate... I alleviate your entire video

This video is amazing. Notice the wing assemblies, weight saving and probably true. Also, look at the variety of adjustments. Look at the in-feed.

Thanks for the tips. I have an old Craftsman table saw which I am considering to upgrade the motor, the belt and upgrading the miter and fence system. Upgrades are about as much as buying a new saw so debating on just going that direction.

Absolutely excellent. LWM

I have had this saw for may years and very happy with the performance, especially with periodic cleaning and tune-ups. Somewhere along the line, I lost the Support Spreader that attaches to the blade guard. Have searched high and low to find a replacement with no luck. Any suggestion on how/where to find one?

good tips thanks

Thanks for the lube tips; you're a life saver!!

Thank You. I did not know that the owner could do all of those adjustments. (Good to know before I get a table saw.)

Great video Sanyi! Just completed a sliding table for my table saw and I was curious what is the best method to align the blade for better accuracy. Greatings from Hungary.

AAA+++ Well done job. Grazie Mille

I see when most adjust the vertical they put a square vertically against the blade. Why do most when adjusting the blade to the slot do they not put a ruler against the blade horizontally extending 10 or so inches front and back. checking from the miter slot would show a bigger adjustment at 10 inches forward or rear of the blade. making it easier to adjust.

Thank you for posting this video. I’m trying to locate the owners manual (in a PDF format) for the Rigid TS 2424 1. I’ve looked online but have not been able to find a link for this Rigid table saw. Would you have any advice on where I might find this manual? Thanks, Mike

What about the front trunnion bolts? Do those need to be loosened?

Question I hope you can help with: I have a direct drive craftsman table saw that sat in a shed for 10 years before I inherited it from a friend. I'd like to use it and it powers right up and the blade spins well with no wobble. Besides removing any obvious rust what should I do to get it shop ready again? I am having real trouble finding any kind of advice on this and I am a pretty good Internet researcher. Any advice is appreciated, even if it's to point me at another resource. Thanks!

Question: how do i weld a trunon of the table saw motor bracket if it fall off.

متشکرم ازشما

use T-9 on the table and rip fence and the wood will glide easily on it

How do you adjust the belt tension? 2:30

Great vid mate. And no waffle!

I have an older craftsman 113.29992 and when I turn up the blade to cut a thicker stock piece the belt gets tight and the saw won’t run. How do I repair this

What model saw is it?

欲しいなあ～

I don't think I'll be laying my table saw on it's side to work on it any time soon, being that it ways a few hundred pounds.

I wish this was as easy as it seems. Check a few things... then realize that the actual table saw top is warped. frustation

Nice and low tech. No dial indicators, no measurement of any kind, just aligning to garden variety references.

I've been investigating diy table saws and found an awesome website at Wilfs wood blueprint (google it if you're interested)

may be that's why my table saw is not cutting straight

That can't be easy with those long press on fingernails.