TURNING A $450 MACHINE INTO A $3000 ESPRESSO MACHINE!: Gaggia Classic Pro FRANKENSTEIN

Подписаться 271 тыс.

Просмотров 502 тыс.

50% 1

EVEN IF YOU DON'T HAVE THIS MACHINE, the video is a fun one. I'm quite proud of this one and hope you enjoy it, even if not in the market for a new machine!
Over the last few weeks since my first GCP video, I have been sourcing and implementing a few different mods for the GCP to epitomize performance. Check bottom of caption for list of prices and time spent on each mod!
Join my Patreon community at:
/ lancehedrick
Find me on IG at:
/ lancehedrick
Find me on Facebook at:
/ lancehedrickcoffee
Special thanks to PWEB and Anarcho on Espresso Aficionado Discord for helping me with the dimmer mod. They were super helpful as I navigated this not well-covered modification.
Special thanks to Mr. Shades for the prompt responses to questions on the PID install (the fix, I'm sure a sigh of relief to him, was the buffoonery of the misplaced decimal haha!)
Time Cues:
0:00- Introduction and Overview
2:08- OPV Spring Replacement
5:22- PID Install
8:47- Dimmer Mod
12:00- Mod Woes (Cuz I'm a Dumb Dumb)
15:39- Demoing the Mods
21:48- Blasting a Shot
26:43- Pouring a Doodle Dairy
28:07- Giving Away Machine and Conclusion
Resources:
All Shades of Coffee installs were guided by manuals from their website- www.shadesofcoffee.co.uk/
For the dimmer, I found this Reddit thread:
www.reddit.com/r/gaggiaclassi...
Also, this:
And this:
coffeeforums.co.uk/topic/1910...
and now Sam Burchard has made a video with the dimmer mod, found here:
• Gaggia dimmer switch mod!
Check out this Canadian Company selling mods:
idrinkcoffee.com/collections/...
Mods (cost/time)
$36.68/0-- Low Profile Tray (www.shadesofcoffee.co.uk/extr...)
$14.11/15min-- OPV Spring Mod (www.shadesofcoffee.co.uk/gagg...)
$135.44/5hrs-- PID (www.shadesofcoffee.co.uk/pid-...)
$32.45/0-- Bottomless Portafilter (www.shadesofcoffee.co.uk/bott...)
$16.93/5min-- IMS Screen (www.shadesofcoffee.co.uk/filt...)
$28.22/0-- IMS Basket (www.shadesofcoffee.co.uk/filt...)
$5.87/1hr-- Light Dimmer (www.walmart.com/ip/GE-Single-...)
$15-/15min- Light Box and Cover (Can't find a link, but bought at Lowe's)
$30-- Miscellaneous screws and wiring
TOTAL: Roughly $315 (excluding VAT and shipping, which put the cost closer to $400 USD)

Развлечения

Опубликовано:

11 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 1,2 тыс.

@LanceHedrick 2 года назад

If you enjoyed the video, or any video on my channel, please give this channel a subscribe and the video a like! I have loads more videos coming from basic coffee lessons (dial in videos coming soon), pourovers, machine comparisons, reviews, more mods, latte art, and more! Thanks for the support. Drop a comment below and I'll get back to you!

@GoFastBeSafe 2 года назад

Is this truly worth more than an $800 machine?

@yulq 2 года назад

Hello! Your PID is overshooting at the beginning probably due to bad P, I & D parameters. Many PIDs has autoset/autoregulate function for these parameters, i.e. it has to be left for some time when it is changing and checking some stuff. After that it should be better. Might be a good idea to check the manual for that or find a manual for the actual PID module mounted in the case. Although, then it could be worse performing during brew or something, so it would be good to at least note default parameters.

@LanceHedrick 2 года назад

I've been told it is due to me not setting up autotune. It never overshoots after the first purge of water, so even without, it is genuinely fine. Thanks for commenting!

@luisefrainsantiagocolon9018 2 года назад

Can I do the dimmer switch mod in a Rancilio Silvia? Do you have a link with more details on the wiring? BTW Nice video!

@LanceHedrick 2 года назад

Yes! You can! And the links are in bio for dimmer switch mods in caption tho they're for GCP. That being said, it is the same exact way in the Silvia. You can absolutely Replicate the process exactly. If need be, google rancilio Silvia dimmer switch mod home-barista

@EvanJGordon 2 года назад

This makes me so happy to see, as I own a hot rodded gaggia classic. I currently have the PID and dimmer mods - but also installed a copper pre-heat coil around the boiler to reduce temperature drop over the course of a shot, and a pressure gauge. I think the pressure gauge is critical for getting the most out of the dimmer mod - since it tells you exactly what pressure you are at for low pressure pre-infusion and pressure profiling shots. Another feature of the dimmer mod that is worth highlighting for people is that if you set the flow just right, you can simulate a spring lever shot - a slow preinfusion ramp up to full pressure, followed by a gentle decline in pressure over the shot.

@normanoslo Год назад

"also installed a copper pre-heat coil around the boiler to reduce temperature drop over the course of a shot". I used usual stainless steel 30-50 usd thermopot with T control, set at holding 94C and got stable pre-heated water, it works like outside boiler. PID is holding 93C this way so long you need it. :)

@weens24 2 года назад

Great video! It's nice to have a well produced video of all these mods together in one place.

@LanceHedrick 2 года назад

Thank you! That was my hope, although I got burned out modding and didnt want to do the pressure gauge lol. Thanks!

@itsxris 2 года назад

phenomenal work, wish a vid like this existed a year ago when I had a GCP!

@LanceHedrick 2 года назад

Haha! Thank you, Xris. For everyone reading, go sub to this man

@itsxris 2 года назад

@@LanceHedrick 🙏🏻

@union310 2 года назад

A simple google search or a search on here will show that none of the "mods' are needed. Perhaps one adjustment with a solid bottom in the portafilter and a pressure gauge whilst you adjust the pressure relief valve.

@xjbladderx 2 года назад

@@union310 Links? I would counter that they are needed... you cannot actually achieve what a PID does without one and an adjustment isn't going to get you that control if that is what you seek. Even with them you are still not at the level of a 3k machine.

@union310 2 года назад

@@xjbladderx Tell me then what any of the mods achieves?

@paulbuffington6706 2 года назад

Great job and info Lance. Also, congratulations on your new FAMILY member !

@LanceHedrick 2 года назад

Thank you! Burping him right now in the hospital haha

@glydic1 2 года назад

Nice job with this project and congratulations Dad! Love to tinker as well and your video inspired me to install a dimmer to control pump voltage thus water flow. The PID controller was installed this summer and has been a really nice addition. First I tried wiring the dimmer from the positive wire attached to the pump switch but it didn't work out really well and made some crazy noises when the dimmer was about half way. Today I tapped the grey wire going directly to the pump which did the trick. So now my GCP is modded pretty much like yours with the exception of the low profile drip tray. I pulled out the drip tray all together and have a shot glass under the overflow tube and scale on the ground giving me lots of room to work. So tomorrow morning I'll attempt my first pre infusion and hopefully pull a couple of nice shots. Appreciate your help and your videos!

@verboeq 2 года назад

My advice is do the join for the dimmer inside the light box, don't try and hide it in the loom. Much safer and looks better.

@nl3712 Год назад

Loving the honesty in this review, thanks a mill!

@cheekster777 2 года назад

Congratulations double Daddy!! Also, very close to 40k subscribers now. Amazing and fully deserved. 👏🏻

@LanceHedrick 2 года назад

Thank you! I'm hoping to somehow hit 40k before the baby comes. Just a fun little goal lol

@NoZenith 2 года назад

You explain so thoroughly yet you keep it moving... that takes talent sir!

@2718rm 2 года назад

Great video! Would love to see a comparison between this mod gcp and higher end machine.

@hodgesmt 2 года назад

Congrats Double Daddy! Great video. My first espresso machine was a saeco aroma that I put a pid on, never could get good shots from it (go figure) I appreciate that your videos are varied, something for everyone. Keep doin' what your doin'.

@LanceHedrick 2 года назад

Thank you so much! I'd thank you by name, but whos in a name? Lol Thanks for watching and commenting!

@markscandariato4015 9 месяцев назад

Just purchased a Gaggia Classic Pro. Thanks for the video... this beats temp surfing!!

@GeroLubovnik 2 года назад

A couple things.... The older Gaggia Classics don't use different springs to change pressure. There is an allen screw adjustment for that under a brass fitting. If you have a pressure gauge it takes about 15 minutes to dial in and you won't break plastic parts. PID's are essential, and there are some good private PID's available for $150 with good instructions. Time to install is about 30 minutes if you're handy. An hour at the max. I don't understand the point of the flow control, as the benefit wasn't fully explained to my satisfaction. The big negative of the Gaggia Classic is the small boiler. By the time you spend the money and do the mods you can have a Rancilio Silva that you can order with PID instlled.

@xenodrake4008 8 месяцев назад

The flow control also changes pressure. The spring just sets the "max" pressure. So if you also put a pressure gauge, you can basically change pressure and temp at will on a super cheap machine.

@mannyr8795 8 месяцев назад

Truth is that this machine is accessible price wise to non nerd espresso lovers. If someone is looking to practice for world barista champ then by all means blow $3000 on a machine but the Gaggia especially the Gaggia evo pro with pressure control (9) is a great by for espresso lovers that aren’t full on nerds

@mannyr8795 7 месяцев назад

@@cray-z578 yes! My main issue now is grinders. I swear to God it was easier to decide on my smoker (and that was a process). Each time I think I’m ready I see another video that puts me back at Step 1. For a 500-700 budget, any recs on good grinders that will last

@gregs3247 6 месяцев назад

Ugh, these Gaggia's. Agreed about the boiler. Temperature issues and "surfing" and other tricks such as the steamer button, waiting for the lights to be on or off a certain number of seconds, and so on. You can taste the difference if you don't get the correct temperature. Not to mention that the boilers corrode and destroy their own selves from the inside out if they don't plug the pump first. I've owned a few Gaggia's, and modded them, but have fallen out of love and don't even recommend them to others any more. Buy a machine double the cost, own it double the time because it won't destroy itself, and quite honestly get better coffee throughout the duration.

@cyclopath1000 5 месяцев назад

i have the pid on both the gaggia and a rancilio. hands down the gaggia is consistently better.

@MrTwins95 Год назад

I've had my GCP for like 2.5 years. I did the OPV mod almost immediatly. Super tempted to do the PID mod now!

@ArgishtiKhachik 2 года назад

I've never had a Gaggia Machine but it was a very informative, interesting and fun video to watch! Fantastic job. Cheers

@LanceHedrick 2 года назад

Thanks for watching regardless! I hope my other videos are helpful to you

@gwynplainez 2 года назад

Amazing! Going to start with the easy ones and probably the spring mod. Let's see how it goes! Thanks for the video!

@LanceHedrick 2 года назад

Absolutely! Spring mod is pretty easy. Good choice!

@mithunfan 2 года назад

What a sick setup! Nicely done Lance. And congrats to the dad and the mom!

@LanceHedrick 2 года назад

Thank you so much! Really appreciate it, friend

@jusumdood4632 2 года назад

Hey Lance! I found your channel recently and I have really enjoyed your content so far. I have had a Gaggia Classic Pro for about a year and a half, and I just started doing some of these "normal" mods myself. So far I have done the bottomless portafilter, upgraded shower screen, and new filter basket. Noticeable results already! I have a 9 bar spring kit and PID on the way. One thing I wanted to point out was that at around 4:40 you mention that the OPV shunts water into your drip tray. It actually shunts water back into the water reservoir. Small detail, I know, but one thing I noticed while examining and cleaning my machine was that the OPV return tube seems to hold on to stagnant water quite a bit. Mine contained a weird, nasty, film that was impossible to remove without taking the tubing out. Just something to keep in mind since that nastiness is getting pumped back into the water your drinking! Thanks again!

@Johanlob1 2 года назад

Indeed, i wonder why it goes back into the reservoir and not the tray.

@zackhoyt2719 Год назад

@@Johanlob1 the old version of the GCP used to dump it into the drip tray. the newer version dumps into the reservoir to avoid filling the drip tray too quickly since the OPV line can put out quite a bit of water

@felipegarcia05189 Год назад

So authentic and genuine haha love your content

@frisbeefrolf 2 года назад

Thanks for the great video! My wife and I are expecting our third child very soon as well and we hope your experience with your newborn has been wonderful. New to home espresso here and your videos are super helpful. Cheers!

@glenovovich 2 года назад

"I am Storm, goddess of the espresso machines! Anyways..." hahahaha

@LanceHedrick 2 года назад

Haha! I get weird when doing longer videos. I just kinda remove my filter and say what pops up 🤣

@mexicanhalloween 2 года назад

@@LanceHedrick I was ready for the cut to your Ororo Munroe cosplay

@LanceHedrick 2 года назад

Haha! Next time... 🤣

@hoseinmohamadzadeh4212 2 года назад

great content 👌 by the way have you heard about screen recorders on phone? 😂😂

@LanceHedrick 2 года назад

Hahaha! I'm about as tech stupid as they come. Lol

@Rafaelgarbulho 2 года назад

Nice mod bro, congrats with your baby! best wishes to the family

@ihavenospacebar231 2 года назад

This reminds me of messing with my Sylvia back in the day, really appreciate you making this video.

@smilersonly 2 года назад

what’s your reasoning behind the 6 bar spring as opposed to the 9 bar spring? i feel like you might have answered this but i wasnt able to find it!

@mcst6969 Год назад

Hoffmann also recommends the 6,5 spring (when he did a similar video). Both of them like lightly roasted coffee, what is probably the answer. AKA slower extraction better taste(with lighter roasts). If you go for a turbo shot then use the 9 bar spring. If you want a slow shot with 9 bar, then you need to grind very fine and use a puck screen, but I don't think this machine is compatible with a puck screen, so channeling is harder to avoid, so I think turbo or 6,5 bar is the answer.

@mcst6969 Год назад

@@Perceptence 🫠that depends on your coffee and grinder. Darker rost are (somewhat) easier to grind to right size(they break up more easy because they have lower volume of moisture). And the grinder should produce even results aka cheap grinders will produce a mixture of fine, medium and large particles on the finest settings. So when extracting the fine part causing more resistance(for the hot water) the bigger ones less. So some parts of your puck are over extracted. In worst case some part are over extracted, some parts are under extracted even channelling can happen in your puck. So you have to back down(in the grind settings), but that might cause you a turbo shot, what if you don't want a turbo shot, then you have back down in pressure: that is why everyone recommendeds the 6,5 bar spring (it's easier to dial in). Sometimes you extracting just fine in the beginning, then over extraction happenes in the end, why because your puck broke up some much in the process it can't produce the right amount of resistance in the end(puck exhaustion). Again you have to adjust the grind settings or pressure. (bonus: in the EG-1 review he said he chocked up the Bianca, that is a 4k euro grinder choking a 2k euro espresso machine. Why, because the grinder producing not just fine, but even particles so channelling didn't happen the machine stopped when the resistance was too high!)

@Nmlss1989 2 года назад

Thanks for all the informative videos! I’ve learned a lot and I’m having a blast watching them (pun intended). Question: How did you decide between the 6.5 and 9bar OPV? What is the rationale behind it? Thanks

@LanceHedrick 2 года назад

Mostly the rationale was I really love 6 bar shots. So, when I'm not flow profiling, I can lazily open the dimmer all the way, let the OPV shunt flow, and have unlimited 6 bar shots haha

@stinkybips 2 года назад

Want to know the same

@LanceHedrick 2 года назад

The lighter the roast, the lower the puck integrity. The lower the puck integrity, the harsher higher pressure is. The harsher the pressure is, the more chance of channeling. 6.5 bars allows both turbo shots (check my video on it if unaware) and allows for lower pressure after soaking the puck.

@77Cfriend 2 года назад

@@LanceHedrick with the dimmer you can even bypass the opv or set it higher like 9- 12bar... then grind very fine with big baskits without choking by having the extra pressure, then back the pressure down to control the flow....basically giving a wider range of pressure to work with for more options

@LanceHedrick 2 года назад

Oh wow! Didn't know you could bypass the OPV. How does that work?

@nbrikha 2 года назад

I just bought a GCP as my first espresso machine after getting a Nespresso as a birthday present last year. I am now several hours into this black hole. I have been looking for exactly this. I can't wait

@coffeeblogua 2 года назад

Finally. Thanks for sharing this idea (even though it's a bit old, I didn't know about such transformation)

@LanceHedrick 2 года назад

Yeah, nothing new here, just democratizing these mods, especially the dimmer mod, which seems to still be pretty unknown. Thanks for watching!

@threehanded8853 2 года назад

Thank You!! I completed everything today: cut opv spring, lamp dimmer switch on right side in front of steam knob, installed manometer on front right, moved Gaggia logo left, setup xmt7100 for 2 relays, pulled a perfect shot, and I now know the pressure is at 8.5 bar. You helped a lot! Here’s how it all works, ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-val-K-Z_YCM.html

@paryzfilip 2 года назад

That is an amazing work! I'm amazed! 😍

@LanceHedrick 2 года назад

Thank you so much! Truly means a lot

@kenphung88 2 года назад

dude you're hilarious and lovin' your energy. Great vid and info

@nullptrRL 2 года назад

This was a fantastic video with some great mods, guides, and explanations about how each mod works! I thought that the temperature offset that you used to account for heat losses was a really neat idea. A few semantic suggestions from an engineer: 1. The temperature controller is called a "PID controller" and not a "PID". "PID" does not really work standalone to refer to a control box, since it refers to the concept behind the control algorithm programmed into the PID controller. 2. The plural of "bar" (as in 9 bar of pressure) is simply "bar" and not "bars". Feel free to ignore these suggestions if it is already too ingrained in your vocabulary to change now or if you don't care. But, if your goal is accurate technical language you should consider trying to make these adjustments. I picked up from the rest of your video that you care about the linguistic precision so that is why I left this comment.

@LanceHedrick 2 года назад

Yep! I'm aware of these. I frequently just screw up and say "bars." As for PID, as with other acronyms or complicated/long names, I tend to abbreviate. But I can certainly change that going forward!

@ShadesofCoffee 2 года назад

Great video Lance - and great to see a Classic with almost as many mods as some of mine :-) You really need The One single hole steam tip on it too… so reach out to me and we’ll fix that for whoever wins the Classic giveaway.

@LanceHedrick 2 года назад

Haha sounds good! Thank you so much for that offer! I still feel silly for setting the dang PID to 9.5C instead of 95C haha. That was miserable.

@ShadesofCoffee 2 года назад

@@LanceHedrick don’t feel so bad - if you originally configure the sensor to be P100 and then set the temp to 95 - and then later you realise it should correctly have been P10.0 then the temp config will change to 9.5. It could have been either issue - but it’s easily done.

@LanceHedrick 2 года назад

I will say I was majorly relieved when I realized that was the issue. I thought I fouled up. Instead, I did the mod correctly and the easiest part I flubbed lol

@vialb2 2 года назад

Love my The One! I dont understand why it's not the standard steam tip, much easier to steam with it. Thanks Soc.

@T100ley 2 года назад

The One single hole is awesome!

@PSlator Год назад

Good video. I had a similar issue when I fitted my PID. it worked for a bit, but one day stopped working. Emailed Shades of Coffee, and went through settings, and found I'd set the temperature to -95 degrees.

@spike443 2 года назад

That was dope. Now I need to read the 400 comments posted in the two days the video's been up, and order the PID and tray. Little trip to HD...I'm always there anyway. Thanks, Lance!!!

@LanceHedrick 2 года назад

Haha! Do it! And good luck with 400 comments hahaha! Appreciate the support watching it!

@spike443 2 года назад

@@LanceHedrick I read them all! If there was a drinking game involving the times you brought up the Breville Dual Boiler, I'd be WIRED! I mean, I'd be drinking lattes, after all.

@LanceHedrick 2 года назад

Hahaha! This is true. And I actually had that recommendation in the original cut but figured I'd cut it. Now I regret it! Lol

@baristakev5709 2 года назад

SHEEESH

@LanceHedrick 2 года назад

Haha! Sheeeeeeeeeee

@vialb2 2 года назад

How much do you really need OPV mod if you have the dimmer mod? I imaging if you control flow, you essentially control the pressure no? Cool video. I'm definetly doing PID mod at some point (also busy with 2nd baby coming soon). I already have OPV mod but I'm curious about the simplicity of the dimmer switch mod. One thing I don't like is the esthetics of the two exposed boxes. But I've seen other options for PID (hiding it behind or other PID kits that sit on top).

@LanceHedrick 2 года назад

So, first, I didn't focus on aesthetics. Lots of better ways to do these. Can mount the dimmer inside and drill a hole, for example. The OPV mod isn't necessary, but it allows me to pull 6.5 bar shots without have to mess with the flow. I would recommend getting the pressure gauge mod if no opv

@vialb2 2 года назад

Yeah, that pressure gauge mode is definetly trickier to install thought but would love to have it. I think it would look good.

@LanceHedrick 2 года назад

It absolutely would. And would help with extractions

@Rahl692 2 года назад

Great video! I have a Silvia with a P.I.D. and now I am thinking about attempting the dimmer switch mod. Thanks, and keep up the great content!

@0x6772 2 года назад

I have exactly the same (my Silvia is… 21 years old, this year, I think? And I installed the PID in… 2010, maybe? I've also replaced the boiler once - it ran dry with the steam wand open during a cocktail party, totally my fault), and, although I'm unemployed right now, so not able to become a Patreon supporter right this second, I, for one, would love to see a similar series of the same mods applied to the Silvia.

@LanceHedrick 2 года назад

Do it! I think you'll absolutely love it. It opens up a whole new world of espresso

@LanceHedrick 2 года назад

Hey! Don't worry about being a supporter right now. It is a difficult time for everyone. I'm just happy you're watching my videos and engaging. I will look into the Silvia.

@theimike4360 2 года назад

Love this video :) great job

@lonelymartyr 2 года назад

That flow control is really interesting. Been using your "Crack the steam wand" hack to preinfuse, but might take a swing at this. Will also say, the PID is absolutely worth it, though it does take several hours to install and you need to read the manual to adjust the settings correctly. 9 bar OPV + brass IMS grouphead block/shower screen mod, and she runs nice and consistent.

@LanceHedrick 2 года назад

Yep! Absolutely. The steam wand hack works, but plummets the temp..should look into the dimmer! And can mount it on the inside and drill a hole for a clean look

@T100ley 2 года назад

@@LanceHedrick Nice! I was curious about that! After the dimmer mod I want to make some cosmetic changes like a wooden steam knob., a wooden pf handle, and now a wooden dimmer knob.

@LanceHedrick 2 года назад

Yes! If you do it, shoot me a pic on IG or somewhere. Would love to see the final product

@ivymike9622 2 года назад

The economic hardship , recession , unemployment and the loss of job caused by covid pandemic is enough to push people into financial ventures .

@LanceHedrick 2 года назад

Sure thing.

@judydomann3321 2 года назад

I have secured financial freedom by investing in bonds , equities , EFT's and some digital currencies .

@jacksongeist6927 2 года назад

Absolutely right, I got 70% of my total portfolio in crypto and I have been making good profits.

@fergursonwatt1309 2 года назад

I wanted to invest more in crypto, but the fluctuations in crypto value discouraged me into dumping.

@sherrilowes9618 2 года назад

How do I contact Mr Benjamin Harold?

@BensCoffeeRants 2 года назад

16:40 ish - I think that's a feature to help heat things up quicker, rather than focusing initially on getting to the right temp which means slowing down and hitting the target temp it overshoots, I'm guessing you're expecting to do a little flush to get all the parts more equalized temperature wise, then it stays more stable at your desired temperature, so that's pretty neat and smart for a PID. Dimmer mod is pretty neat but ideally you want a pressure gauge with it!

@Thrilos30 2 года назад

Amazing content as always!

@LanceHedrick 2 года назад

Thank you so so much! Really appreciate it

@artichaug1719 2 года назад

Thanks for this fun and candid video

@LanceHedrick 2 года назад

Absolutely! Thanks for watching and the support

@murataht 2 года назад

I have seen someone has modded his delonghi machine (which has a boiler) with those things, even added a pressure gauge to observe the dimmer affect. I was impressed and wanted to do the same with my delonghi ec155, but I chickened out. But your video gave me some encouragement, I will look around a bit more to find more information on those mods. Thanks !

@LanceHedrick 2 года назад

Do it! The mods will bring your espresso to another level completely!

@rajahawa6888 2 года назад

You're the man! Thank you for this video

@LanceHedrick 2 года назад

Thank you for watching and the support!

@segamble1679 2 года назад

10:39 "how *awesome* does that sound?" Just about killed me.

@ahikernamedgq 2 года назад

Lance - this is awesome. Thank you for sharing.

@LanceHedrick 2 года назад

Thank you for watching! The support is massive

@shanewilson2152 2 года назад

Great video Lance

@pyrotelekinesis7253 2 года назад

Congratulations on the new baby! 🎊

@LanceHedrick 2 года назад

Thank you so much!

@samburchard1778 2 года назад

I just added the dimmer mod to my machine, AMAZING help to my brewing with a naked portafilter. No more spurting, and no more channeling. Best part is; I made a video showing the basics of how I did it. The first one on the internet as far as I know. Anyways, great video Lance! I love all the content you've been putting out. I hope we might see more on the gaggia in the future

@LanceHedrick 2 года назад

Oh hell yeah! Good! Link me to the vid and I'll link in my caption

@samburchard1778 2 года назад

@@LanceHedrick Nerding out cause I just got a reply from one of my favourite coffee people xD. Here it is! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-_iB_5xtS7ak.html&ab_channel=SamBurchard

@LanceHedrick 2 года назад

Thank you! Added to the caption

@samburchard1778 2 года назад

@@LanceHedrick Awesoooommmeeee! Thanks man!

@autoexec5367 2 года назад

this is sick! thanks for sharing! 😍

@LanceHedrick 2 года назад

Thank you for watching! The support means a lot

@CrippledKittens13 2 года назад

Awesome video and work

@morningcoffee1 2 года назад

Man, really a great video.

@Taziod Год назад

This so so well done man idk if I'll watch any more but jeez I'm subbing. The x-men hype got me so good. Grats on the baby

@LanceHedrick Год назад

Thank you so much! Really means a lot that you'd give the sub even without intention of watching more. Appreciate the support!

@tafsen 3 месяца назад

Thanks for a great video! When can we expect part 2?

@juancarlosfallas4535 2 года назад

"Here you go you nerds!" 😂😂😂😂 Love your energy brother, never change!!!!

@howardkim2067 2 года назад

Great video and congrats 🎉

@LanceHedrick 2 года назад

Thank you so much! We are excited

@MatthewRSimpson 2 года назад

Congratulations on your baby. Hope everything went well.

@sanjayajha362 2 года назад

Great advice for GCP users! Thanks!!

@LanceHedrick 2 года назад

Thank you! Much appreciated. Thanks so much for watching!

@jdupuis4829 2 года назад

Wow! That looks awesome! Super geeky!

@LanceHedrick 2 года назад

Haha thanks! It is quite fun and really rewarding on top of increasing the cup quality!

@zenadventurer69 2 года назад

Great video as always…basically it is the best video I’ve seen endorsing the Breville (Sage) Infuser…lol.

@andreihlen7597 2 года назад

That's really cool, impressive!

@LanceHedrick 2 года назад

Thank you so much! Happy for your support

@brianruggiero2254 2 года назад

Congratulations on the baby!

@LanceHedrick 2 года назад

Thank you! We go in at 6am for the induction. Hope all is going to be well!

@media1981 2 года назад

Bro that was genius! Haha always pleasure to hear your jokes 😆 keep up the good work!

@LanceHedrick 2 года назад

Haha! Thank you so much! Really, really appreciate the kind words and support

@nickrockon Год назад

wow vintage lance. production has come so far

@karvalhokgmail 2 года назад

Congrats for the new baby!

@LanceHedrick 2 года назад

Thank you! About to leave the hospital with the little tyke

@MrAnthonydawson 2 года назад

Great video, thanks for sharing.

@LanceHedrick 2 года назад

Thank you so much for the kind words and support!

@jonlang5747 Год назад

Just ordered a GCP and I am a instrument tech, so looking forward to the modes! Thing is I am an espresso virgin but look forward to watching your content! Thanks!

@graememorrison333 Год назад

Let's all face it. It's less about extracting something tasty from ground coffee beans and more about extracting the most out of a machine. And quite right too!

@damon123jones 2 года назад

amazing work doctor

@LanceHedrick 2 года назад

Hahaha! Thank you, watson

@InvestorBen 5 месяцев назад

Thank you for the informative video. Just got a GCP Evo and will probably start tinkering soon. How did you get the Smart Espresso Profiler to work with the GCP? Happy to manually press buttons and pull levers, but would love to have the profiler tell me exactly what is going on! Thanks again!

@dustinfletcher2831 2 месяца назад

Hi Lance, I'm discovering this video just now, since I clicked on the link from your recent "Ultimate Espresso Machine Modification" Video. I started watching that but then decided this would be a good starting point. I'm not sure if it's something that you've figured out yet, but if you can change your PID gain values, then the reason that your water initially heats past the set temp is because dynamic systems will always have overshoot after the initial ramp. Since the only function you have is to heat, the system can't control cooling values and as such it just needs to wait for the system to cool down from the ambient temperature, hence why once you flush the grouphead you're able to bring it back down to the right temperature. You can prevent the initial overshoot by increasing the D (Derivative) gain control value, but this will also increase the rise time of the system, making it take longer to heat up. You can typically tune it pretty well so that you can find a balance between increased rise time and very minimal overshoot.

@jmoore9806 2 года назад

Bro you just blew my mind....that has to be the coolest mod ever with the dimmer.....I'm soo getting that mod

@LanceHedrick 2 года назад

Haha thank you! Glad you enjoyed it!

@plaspohlme 2 года назад

Love your videos!

@LanceHedrick 2 года назад

Thank you so much! The support means a ton

@AdamSchlesingerD 2 года назад

This is a great video to find. I need to take apart my classic anyway for repair reasons.

@LanceHedrick 2 года назад

Thank you! So glad you found it and enjoyed it

@TheBase94 2 года назад

Thanks a lot! I am still thinking about getting a GCP, and was looking for a complete video describing all the popular mods. If I buy one I'll just install first OPV spring mod and taking a bottomless porta filter and IMS basket . Also know a electrical ingineer if I ever want to install later the PID mod

@officialtwinzmusic 2 года назад

Same

@MuhammedSalihAta Год назад

Great work

@StartCodonUST 2 года назад

This man probably just saved me a few thousand dollars. Maybe in a few years I'll take the plunge and get a Decent and a Lagom P100 or whatever the most-hyped espresso machine and grinder combo will be at that time. But for now I feel like a modded Gaggia Classic Pro and a modded DF64 with SSP burrs (or even just my Option-O Helor 101/Remi hand grinder for now) is 90% as user-friendly and capable for insanely less money.

@karlsinki986 2 года назад

Congrats on the newborn Lance!

@LanceHedrick 2 года назад

Thank you, Karl! About to leave the hospital with him now 😍

@dmdrosselmeyer Год назад

Congratulations on the little one!! I get they're probably about a year old by now but it's never too late lol

@T100ley 2 года назад

I am only missing the dimmer mod! I am so doing that, light roasts are still really difficult for me to get right. I'm using the steam wand as a way to create a pseudo-pre-infusion, but the flow control without having to waste the water from the steam wand is awesome. Terrific video and furthers my appreciation for my GCP.

@LanceHedrick 2 года назад

Yes! And the dimmer will disallow as much heat loss as the wand trick does

@cheekster777 2 года назад

*Upgrades!* 😎 Thanks, Lance.

@LanceHedrick 2 года назад

Thank you! And shocked you weren't first comment today! Probably faked you out with two posts in one week haha!

@cheekster777 2 года назад

@@LanceHedrick - Ha ha, yes. Still recovering from a nasty accident a couple of weeks ago. 😕

@LanceHedrick 2 года назад

Oh yikes. Please get better asap!

@bissmik5 Год назад

"There you go, nerds" just about did it for me - Thanks for all the info and demos!

@Toppleover 7 месяцев назад

😂 This might be the best Lance video yet

@ritaweygint4038 8 месяцев назад

I’m just finishing up these mods (PID, pressure gauge, dimmer/flow control) installed in Shades’ Top Box. I love a good project, but these mods are very challenging on the newest Gaggia Classic Evo Pro machines. It’s really tight in there…! You’re going to have to read the manual most likely. Mr. Shades is awesome though! Got me sorted out a few times during the process. I got the Gaggia partly to be able to do these mods, and it’s a great little machine!

@black58 7 месяцев назад

I was also thinking of buying the PID and OPV from shades, can you recommend it? Im not a beginner in building things at home like furniture but have no idea about wires, can I still do it?

@Coffeeology 2 года назад

I'm getting a gaggia next week. I''ve already got the 9 bar spring ordered, naked portafilter ordered. Have a good one.

@LanceHedrick 2 года назад

Heck yeah! That is awesome! You will love it.

@erickmorin2660 2 года назад

I did the OPV spring, the buttomless portafilter and the IMS screen. And soon the low profilw tray, the IMS basket and a silicone gasket.

@LandsoulFFXI 2 года назад

I've had the Gaggia Classic Pro for years and I did the spring mod but not the PID mod. I've been very pleased with the machine for many years. It makes excellent espresso and cannot recommend the machine enough. It's really an amazing machine for the money the quality of coffee you get out of it. I eventually upgraded to an E61 HX machine which makes a lil better espresso more consistently than the Gaggia but I would not say it's a world of difference but more convinience allowing you to steam and brew at the same time. PID and some other features the Gaggia doesn't have. Though, for many years I have enjoyed using the Gaggia Classic and imo unless you really are prepared to take your coffee to the next step it could be very well that the Gaggia will be your only machine you'll ever buy. Machine is also build to last for decades. It's almost unlikely that something breaks in the machine.

@LanceHedrick 2 года назад

For sure! Really well put. Thank you for sharing your experience and leaving this comment. Cheers

@jimgd4 7 месяцев назад

I just ordered a New Gaggia Classic Evo Pro today. Thank you for this great video. This is the first of your videos that I have seen. After all is said and done, would you rather have a Rancilio Silvia for the money? I appreciate the input.

@CharlesSpragins 10 месяцев назад

you posted this 2 yrs ago, and I found your channel and I love it. I have an old Cuisinart espresso machine. the pods are cheap and each one has a single output hole. I bought an upgrade 51mm basket and filter full of holes, the water comes out so fast it's too much; however with this mod he he he I can get the crema and rate I really need without the pressure washer effect. even used the old filter basket on the new handle and it literally was a jet stream. again this will solve my issue for now until I get a high end machine. I hate I didn't think of it. also Cuisinart has plastic check valves no springs that is able to be modded. I'll research more on the output heat but as far as I can tell all are connected to a single heat source if anyone else reads this :)

@MagicRMZ 17 дней назад

Thank god I found this video I’m going to be doing this soon

@yyoud88 Год назад

Hi Lence. Thank you very much for the inspiring video. I am thinking to try 6.5bar spring mod, but wondered if it affects steam pressure and, as a result, the quality of the steamed milk. What do you think?

@TrissyT73 2 года назад

Awesome vid dude

@LanceHedrick 2 года назад

Thank you, Tristan! Means a lot

@TrissyT73 2 года назад

@@LanceHedrick no dramas dude. Just Instagram messaged you

@teskio 2 года назад

I’ve watched this video 9 times now. I got the OPVs…the other stuff, I need to sit atop a mountain and ask the Gods if I should. Love your channel

@LanceHedrick 2 года назад

Hahaha! I love it. Thank you for the support!

@stevecraig1203 2 года назад

That’s the setup I had before my decent. It was fun snd made some surprisingly good shots.

@LanceHedrick 2 года назад

Absolutely! I have a decent as well and love it, but this was a fun project! And very fulfilling haha

@bradyvilhauer4445 2 года назад

HAHAHA Lance normally I dismiss your cheeseball humor but that double daddy 2 daddy espresso like the rivers from the mountains had me WEAK!!!! Love this content man, your stuff is always good but this felt especially relaxed and natural. I am very tempted to mess with this mod some day as 2-3k is a bit high for the other options. Thanks bro!

@LanceHedrick 2 года назад

DISMISS MY CHEESEBALL HUMOR?! What is this. 🤣🤣🤣 Glad you enjoyed it!

@louismurphy1403 3 месяца назад

Hey lance, wonderful video as always. Do you know if you can do Spro'over type shots on these? The reason i ask is that I've heard you should only run continuous shots for around 45-50 seconds whilst using the dimmer, to avoid damaging the machine. Cheers, Louis

@Tobywan82 9 месяцев назад

GREAT video! The links for the IMS screen and basket don't work. Which screen and basket do you recommend?

@aendroid22 7 месяцев назад

Hi , great vid brother . I've been looking at the GCP for a little bit but i dont want to do too many mods , is replacing the basket and the 12 bar spring (to a 9 bar spring) good enough to yield amazing shots ?